Langley-Empire MV 145, MV 120, MV 130 User Manual
INSTALLATION INSTRUCTIONS
AND
OWNER´S MANUAL
GRAVITY DIRECT VENT
WALL FURNACE
TABLE OF CONTENTS
SECTION
Important Safety Information
Safety Information for Users of LP Gas
Introduction
Specifications
Gas Supply
Clearances
Installation Instructions
Lighting Instructions
Pilot Flame Characteristics
Main Burner Flame Characteristics
PAGE
3
4
5
5
6
7-8
8-10
11
12
12
Maintenance
How to Order Repair Parts
Parts List
Parts View
Troubleshooting
12-13
13
14
15
16
Page 2 MV1XX-2-0404
IMPORTANT SAFETY INFORMATION
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.
• Due to high temperatures the appliance should be
located out of traffic and away from furniture and
draperies.
• Children and adults should be alerted to the hazards of
high surface temperatures and should stay away to avoid
burns or clothing ignition.
• Young children should be carefully supervised when
they are in the same room as the appliance.
• Clothing or other flammable material should not be
placed on or near the appliance.
• Any safety screen or guard removed for servicing an
appliance must be replaced prior to operating the
appliance.
• Keep burner and control compartment clean.
• Vent cap hot while furnace is in operation.
• Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be
inspected before use and at least annually by a qualified
service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding materials,
etc. It is imperative that control compartments, burners
and circulating air passageways of the appliance be kept
clean.
• DO NOT put anything around the furnace that will
obstruct the flow of combustion and ventilation air.
• DO keep the appliance area clear and free from
combustible material, gasoline and other flammable
vapors and liquids.
• DO examine venting system periodically and replace
damaged parts.
• DO make a periodic visual check of pilot and burner.
Clean and replace damaged parts.
• CAUTION: Pilot hole cover must be kept tightly closed
during operation.
• DO NOT use this heater if any part has been under
water. Immediately call a qualified service technician to
inspect the heater and to replace any part of the control
system and any gas control which has been under water .
Page 3MV1XX-2-0404
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions which can protect both you and your family from
an accident. Read them carefully now, then review them
point by point with the members of your household.
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building or area. Do that
IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas
such as basements. When you have reason to suspect a
gas leak, keep out of basements and other low areas. Stay
out until firefighters declare them to be safe.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell
the odor of the chemical put into the gas. Y ou must find out
if you can smell the odorant in propane. Smoking can
decrease your ability to smell. Being around an odor for a time
can affect your sensitivity or ability to detect that odor.
Sometimes other odors in the area mask the gas odor. People
may not smell the gas odor or their minds are on something
else. Thinking about smelling a gas odor can make it easier to
smell.
The odorant in LP-gas is colorless, and it can fade under
some circumstances. For example, if there is an underground
leak, the movement of the gas through soil can filter the
Someday when there may not be a minute to lose,
everyone's safety will depend on knowing exactly what to
do. If, after reading the following information, you feel you
still need more information, please contact your gas
supplier.
• Use your neighbor's phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not reenter the building or area.
• Finally, let the service man and firefighters check for
escaped gas. Have them air out the area before you return.
Properly trained LP-Gas service people should repair the
leak, then check and relight the gas appliance for you.
odorant. Odorants in LP-Gas also are subject to oxidation.
This fading can occur if there is rust inside the storage tank or
in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That
will take some of the odorant out of the gas, reducing its odor
intensity.
LP-Gas may stratify in a closed area, and the odor intensity
could vary at different levels. Since it is heavier than air, there
may be more odor at lower levels. Always be sensitive to the
slightest gas odor. If you detect any odor, treat it as a serious
leak. Immediately go into action as instructed earlier.
SOME POINTS TO REMEMBER
• Learn to recognize the odor of LP-gas. Y our local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-Gas has a weak or abnormal odor, call your LPGas Dealer.
• If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-Gas
system. If you are qualified, consciously think about the
odor of LP-Gas prior to and while lighting pilot lights or
performing service or making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
to set too long before refilling. Cylinders and tanks which
Page 4 MV1XX-2-0404
have been out of service for a time may develop internal
rust which will cause odor fade. If such conditions are
suspected to exist, a periodic sniff test of the gas is
advisable. If you have any question about the gas odor,
call your LP-gas dealer. A periodic sniff test of the LPgas is a good safety measure under any condition.
• If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the
same immediate action recommended above for the
occasion when you do detect the odorized LP-Gas.
• If you experience a complete "gas out," (the container is
under no vapor pressure), turn the tank valve off
immediately. If the container valve is left on, the container
may draw in some air through openings such as pilot light
orifices. If this occurs, some new internal rusting could
occur. If the valve is left open, then treat the container as a
new tank. Always be sure your container is under vapor
pressure by turning it off at the container before it goes
completely empty or having it refilled before it is
completely empty.
INTRODUCTION
Introduction
Always consult your local Building Department regarding
regulations, codes or ordinances which apply to the
installation of a direct vent wall furnace.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card
supplied with furnace.
3. Installer should show owner how to start and operate
furnace and thermostat.
Warning:
Any change to this furnace or its control can be
dangerous. This is a heating appliance and any panel,
door or guard removed for servicing an appliance
must be replaced prior to operating the appliance.
General Information
This furnace is design certified in accordance with American
National Standard/CSA Standard Z21.86b and CSA 2.32b2002 by the Canadian Standard Association, as a Gravity
Direct Vent Wall Furnace to be installed on an outside wall
according to these instructions.
Any alteration of the original design, installed other than
as shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
All correspondence should refer to complete Model No.,
Serial No. and type of gas.
Notice: During initial firing of this unit, its paint will bake out
and smoke will occur. To prevent triggering of smoke alarms,
ventilate the room in which the unit is installed.
Installation in Residential Garages
Gas utilization equipment in residential garages shall be
installed so that all burners and burner ignition devices are
located not less than 18" (457 mm) above the floor.
Such equipment shall be located, or protected, so it is not
subject to physical damage by a moving vehicle.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization
equipment or accessories and repair and servicing of
equipment shall be performed only by a qualified agency. The
term "qualified agency" means any individual, firm,
corporation or company which either in person or through a
representative is engaged in and is responsible for (a) the
installation or replacement of gas piping or (b) the connection,
installation, repair or servicing of equipment, who is
experienced in such work, familiar with all precautions
required and has complied with all the requirements of the
authority having jurisdiction.
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code ANSI
Z223.1/NFPA 54* Natural Gas and Propane Installation Code,
CSA B149.1.
*Available from the American National Standards Institute, Inc., 11 West
42nd St., New York, NY 10036.
High Altitudes
For altitudes/elevations above 2,000 feet (609.9 m), input
ratings should be reduced at the rate of 4 percent for each 1,000
(305m) feet above sea level. Canadian High Altitudes for
locations having an elevation above mean sea level between
2,000 feet (609.9 m) and 4,500 feet (1370m), use orifices as
indicated in the following table:
MOD
MV 120
MV 130
MV 145
0-2000feet (0-610 m) 2000-4500 feet (610-1370 m)
NG
0.053” (1.35 mm)
0.070” (1.77 mm)
0.077” (1.95 mm)
LPG
0.035” (0.88 mm)
0.043” (1.10 mm)
0.053” (1.35 mm)
NG
0.050” (1.27 mm)
0.066” (1.67 mm)
0.072” (1.83 mm)
LPG
0.033” (0.83 mm)
0.041” (1.03 mm)
0.050” (1.27 mm)
SPECIFICATIONS
Model
Input BTU/HR (KW)
Min. Input BTU/HR (KW)
Efficiency Rating* (%)
Height (inches / mm)
Width (inches / mm)
Depth (inches / mm)
Gas Inlet
Input Vent Diameter (inches / mm)
Output Vent Diameter (inches / mm)
*The efficiency rating of the appliance is a product thermal efficiency determined under continuous operating conditions and was
determined independantly of any installed system.
MV1XX-2-0404
MV 145
20,000 (5.81)
6,900 (2.00)
72%
24.4 / 620
27.3 / 688
6.75 / 170
3/8” NPT
6 1/4” (160 mm)
3 1/2” (89 mm)
MV 130
14,000 (4.07)
6,000 (1.74)
72%
24.4 / 620
27.3 / 688
6.75 / 170
3/8” NPT
4 3/4” (121 mm)
2 5/8” (67 mm)
MV 120
8,400 (2.44)
3,800 (1.10)
72%
24.4 / 620
21.2 / 538
6.75 / 170
3/8” NPT
3 9/16” (90 mm)
2 1/8” (54 mm)
Page 5
GAS SUPPLY
Locating Gas Supply
The gas line can enter the unit either through the floor or
outside wall. The gas line opening should be made at this time.
Location of the opening will be determined by the position of
floor joists and the valve and union used for servicing.
Recommended Gas Pipe Diameter
Pipe Lenght
(Feet)
0 - 10
10 - 40
40 - 100
100 - 150
Schedule 40 Pipe
Inside Diameter
Nat.
1/2”
1.3 cm
1/2”
1.3 cm
1/2”
1.3 cm
3/4”
1.9 cm
L.P.
3/8”
1.0 cm
1/2”
1.3 cm
1/2”
1.3 cm
1/2”
1.3 cm
Tubing, Type L
Outside Diameter
Nat.
1/2”
1.3 cm
5/8”
1.6 cm
3/4”
1.9 cm
7/8”
2.2 cm
L.P.
3/8”
1.0 cm
1/2”
1.3 cm
1/2”
1.3 cm
3/4”
1.9 cm
Note: Never use plastic pipe. Check to confirm whether your
local codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes,
it is always best to consult your local authority and installation
code.
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal
Tubing and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of
Other Than All-Metal Construction
The above connectors may be used if acceptable by the
authority having jurisdiction. The state of Massachusetts
requires that a flexible appliance connector cannot exceed
three feet in length.
FLEXIBLE GAS LINE CONNECTION
Gas
Supply
Flare Shut
Off Valve
Tee
Handle
Tubbing
Flare FittingFlex
NPT Niple
RIGID GAS LINE CONNECTION
Tee Handle
Compounds used on threaded joints of gas piping shall be
resistant to the action of liquefied petroleum gases. The gas
lines must be checked for leaks by the installer. This should be
done with a soap solution watching for bubbles on all exposed
connections, and if unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance
must be disconnected from piping at inlet of control valve
and pipe capped or plugged for pressure test. Never
pressure test with the appliance connected; control valve
will sustain damage!
A gas valve and ground joint union should be installed in the
gas line upstream of the gas control to aid in servicing. It is
required by the National Fuel Gas Code that a drip line be
installed near the gas inlet. This should consist of a vertical
length of pipe tee connected into the gas line that is capped on
the bottom in which condensation and foreign particles may
collect.
Alternate locations
for shut off valve
Gas supply inlet
3” (76 mm)
DRIP LEG
Figure 2
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3 mm)
N.P.T. plugged tapping, accessible for test gauge
connection, must be placed immediately upstream of the
gas supply connection to the appliance.
2. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system
at test pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the above procedures results in pressures
in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas
valve, it will result in a hazardous condition.
NPT Gas
Supply
Valve
NPT Union
NPT NipleClose NipleShut Off
Figure 1
Consult the current National Fuel Gas Code, ANSI Z223.1
CAN/CGA-B149 (.1 or .2) installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock. In the
state of Massachusetts the gas cock must be a T handle type. A
manual main gas cock should be located in the vicinity of the
unit. Where none exists, or where its size or location is not
adequate, contact your local authorized installer for
installation or relocation.
Page 6
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure
regulator in the gas valve. Natural gas models will have a
manifold pressure of approximately 4.0" w.c.(0.996 kPa) for
MV120 and 130 or 6.0" w.c.(1.494 kPa) for MV145 at the
valve outlet with the inlet pressure to the valve from a
minimum of 5.0" w.c.(1.245 kPa) for MV120 and 130 or 7.0"
w.c.(1.742 kPa) for MV145 for the purpose of input
adjustment to a maximum of 10.5" w.c.(2.61kPa). Propane gas
models will have a manifold pressure approximately 10.0"
w.c.(2.49kPa) at the valve outlet with the inlet pressure to the
valve from a minimum of 11.0" w .c.(2.739kPa) for the purpose
of input adjustment to a maximum of 13.0" w.c.(3.237kPa). A
1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge
connection, is located on the outlet side of the gas control.
MV1XX-2-0404
CLEARANCES
1. In selecting a location for installation, it is necessary to
provide adequate accessibility clearances for servicing and
proper installation. In order to that, at least 6”(152 mm)
should be left clear from the wall on right side of the cabinet
and 4” (101 mm) on left side.
2. Unit is supported by a wall support plate secured to the
wall.
3. The minimum clearances from casing to combustible
construction is 36" (914 mm) on top, 4" (102 mm) on each
side and 4" (102 mm) from the floor or from the top surface
of carpeting, tile or other floor covering and 0" (0 mm) to
rear wall.
4. The minimum distance from the center of the vent cap to the
nearest outside corner or obstruction is 16" (407 mm).
5. The MV 120, MV 130 and MV 145 minimum wall depth is
4 1/2”(114 mm) and the maximum is 12”(305 mm). The
G
D
E
B
L
C
A
use of tubes not supplied by the manufacturer results in
unsatisfactory performance.
The vent cap of a direct vent appliance, with an input of 10,000
Btu/h (3 kW/h) or less shall be located at least 6" (150 mm)
from any opening through which flue gases could enter a
building; for appliances up to 50,000 Btu/h (14.6 KW/h) this
distance shall be at least 9" (229 mm). The bottom of the vent
cap and the air intake shall be located at least 12" (305mm)
above grade.
W ARNING: The nearest point of the vent cap should
be a minimum horizontal distant of six (6) feet
(1.83m) from any pressure regulator. In case of
regulator malfunction, the six (6) feet (1.83m)
distance will reduce the chance of gas entering the
vent cap.
Vent teminal
V
Air supply
X
Area where
terminal is
not permitted
F
Vent terminal clearances
A= clearance above grade, veranda, porch, deck
or balcony
B= clearance to window or door that may
be opened
C= clearance to permanently closed window
D= vertical clearance to ventilated soffit located
above the terminal within a horizontal distance
of 2 feet (61 cm) from the center line
of the terminal
E= clearance to unventilated soffit
F= clearance to outside corner
G= clearance to inside corner
H= clearance to each side of center line extended
above meter/regulator assembly
I= clearance to service regulator vent outlet
A
CANADIAN INSTALLATIONS
12” (30 cm)
6” (15 cm) for appliances 10,000 Btu/h
(3 kW), 12” (30 cm) for appliances 10,000
Btu/h (3 kW) and 100,000 Btu/h (30 kW)
clearance in accordance with local
installation codes and the
requirements of the gas supplier
3 feet (91 cm) within a height 15 feet (4.5 m)
above meter/regulator assembly
<
3 feet (91 cm)
<
1
>
Figure 3
US INSTALLATIONS
12” (30 cm)
6” (15 cm) for appliances 10,000 Btu/h
(3 kW), 9” (23 cm) for appliances 10,000
Btu/h (3 kW) and 0,000 Btu/h (15 kW)
clearance in accordance with local
installation codes and the
requirements of the gas supplier
clearance in accordance with local
installation codes and the
requirements of the gas supplier
< 5
2
<
>
Page 7MV1XX-2-0404
INSTALLATION INSTRUCTIONS
Location of Furnace
The heater must be on an outside wall in the room to be heated.
When choosing a location for the furnace please remember
that the vent cap supplied with the unit must be installed
without alteration, with the exception of cutting the vent tubes
and insulation to length, as directed in these instructions. The
outside vent cap needs to be flush to the wall, so select a
relatively smooth exterior surface.
Since this appliance is a direct vent (balanced flue) design, all
combustion and ventilation air is drawn from outside of the
structure. No special considerations for combustion are
necessary inside the structure. Once you have determined that
the exterior vent will meet the clearances above, you must
locate the heater on the inside wall of the room to be heated.
Begin the installation by locating the wall studs on the inside
wall of the structure. Find the centerlines between the studs
where you want the unit to be mounted.
serving a separate solid-fuel burning appliance.
Locating Wall Opening
A full scale template is furnished with the unit which
illustrates the vent and gas supply openings and mounting
holes in their correct locations on the wall.
Note: the figure 4 gives the required dimensions for mounting
the unit, in the event that the template is unusable or lost.
Place the template on the wall so that the vent opening will be
located between the studs and, in the case of the MV 130, for
example, the bracket mounting holes are over the studs (16” /
406 mm, on center). DO NOT CUT THE WALL STUDS IN
ORDER TO INSTALL THE UNIT. Place the bottom edge of
the template directly on the floor or the floor covering such as
carpeting or tile.
Installing the Unit
Make sure that the location you have selected for the furnace
complies the requirements above before its installation.
This gas appliance must not be connected to a chimney flue
Tw984 35838dds on the in so 12 0.1 u86008 m490.351.9253.7990 497. 0.099.09 R4TwS6urface.
Cutting the Vent Hole
Begin the installation by locating the wall studs on the side
wall of the structure. Find the centerlines between the studs
where you want the unit to be mounted. Refer to the following
illustration (Figure 5) for a side view of how the finished
installation should look. This appliance is certified for
installation on walls which are a maximum of 12” (305 mm)
thick. The vent assembly supplied with the unit will
accomodate walls up to that thickness.
With the template flat and level against the inside wall, mark
the location for the opening for the vent assembly as well as the
location of the two holes for mounting the wall support plate
and the one for the gas supply, if the supply is to be through the
wall. If desired, (and in accordance with all applicable
building and plumbing codes) the gas piping can be brought
into the room through the floor underneath the unit.
Remove the template from the wall and with a long drill, make
a hole in the center of the opening for ventilation all the way
through inside and outside wall. Trace the wall opening in
INSTALLATION INSTRUCTIONS (cont.)
the indicated diameter in both walls and cut them. Your hole
will be about 1 to 2” (26 to 52 mm), depending on the unit
model, larger in diameter than the vent pipe.
Pilot burner
viewing
Make sure the two holes (in the inside and the outside wall) are
concentric to one another and line up. If the opening in the
outside wall is higher than the opening in the inside wall, water
from rain or from lawn sprinklers could enter the vent cap and
drip back into the heater, causing it to rust out. Use a
carpenter´s level and square to confirm that the two holes are
level and in line with one another.
If the vent cap is to be installed on shingles or clapboards, or if
it appears that a projection within 6” (152.4 mm) of the air inlet
section could shield the air inlet, the entire vent should be
supported away from the wall as shown in Figure 6.
wall and fasten the vent cap to the wall using the 4 screws
(provided with the unit) in the holes prepared in the vent cap
plate.
Making certain that the vent cap is flushed to the outer wall,
draw a line all the way around the vent pipe where it comes
through the inside wall. (Note: this line only marks the point
where the pipe comes through the wall. It is not where you
will cut the pipes).
Remove the vent assembly from the wall. Measure 7/ 16” (11
mm) from the line just made and make a mark towards the
open end of the pipe.
Mark several spots around the pipe insulation at this 7/ 16”
(11mm) distance and then tape a sheet of paper around the pipe
at this time to assure an even cut.
Use a cutter knife to cut only the insulation and its lining and a
hack saw or tin snips to cut the larger pipe at the cut line on the
edge of the paper.
Cut a clean, straight line on the outside tube, being careful not
to crimp or deform the tube.
It is very important that this be a clean straight cut for the
heater to perform properly.
On MV 120 and MV 130 units, you must proceed to cut the
insulation again through the line originally traced (flush line of
the inner wall, 7/16” back from the cut end of the tube). (See
drawing)
On MV145 units, you must proceed to cut the lower edge of
the insulation (only this part, not the complete circumference)
to allow the ventilation come through the wall mounting
support bar. Cut according following drawing:
Support
box
Vent cap
Figure 6
For vinyl siding installation, order the appropriated kit
through the Parts Department.
Note: the vent assembly of MV 145 units has off-centre tubes
and must be installed in a certain position. Make sure the arrow
engraved on its ring is located in the upper position. If not,
connecting the inner pipe in the appliance won´t be possible.
Marking and cutting the vent pipes to the proper length
From the outside of the building, push the vent assembly
through the hole until the vent cap flange is against the outer
Figure 7
Measure now 2” (50.8 mm) from the cut end of the larger pipe
and make a mark on the inner pipe. Be certain that the inner
pipe is thoroughly marked so that it will be 2” (50.8 mm)
longer than the larger pipe when cut. The inner pipe needs to be
cut with a hacksaw.
Remember to remove the vent assembly from the wall in
order to cut the tubes
Installing the vent assembly and wall support plate
In case outside wall is of tiled wood construction, rough or
unlevelled, the use of silicone sealing compound to avoid
INSTALLATION INSTRUCTIONS (cont.)
Figure 8
eventual water filtration or the entrance of bugs is necessary.
Press the flange against the outer wall surface and fasten the
vent cap to the wall using the 4 screws (provided with the unit)
in the holes prepared in the vent cap plate. Once the vent is
secured to the wall, proceed filling the gaps between the vent
plate and the wall with silicone sealing compound.
Inside the building, place the wall support plate (which is
taped inside the cabinet during shipment) over the open end of
the vent pipe and push the plate firmly against the interior wall.
You might need to handle the introduction of the larger
pipe into the hole of the support plate with your fingers
since the pipe could have suffered some minor
deformation through the cutting process.
Now level the plate with carpenter level and mark the
mounting holes with a pencil (see Figure 8). Remove the wall
support plate from the vent pipe and drill the two holes with the
appropriate drill bit.
Place the wall support plate over the vent pipe again and affix
the plate to the wall using the two screws provided with the
unit.
Note: hollow wall fasteners (also supplied with the unit)
are necessary for model MV 120. Models MV 130 and MV
145 can be mounted on the wall studs.
Important: remove styrofoam inside front cover now .
Remove the small piece of wood from the rear of the heater
and discard. Four small adhesive foam pads are included with
the unit and can be found in the accessory bag. Place the foam
pads on the four raised “bumps” on the rear of the unit.
These foam pads will protect the wall surfaces from
damage.
Hang the heater on the arms on the wall support bracket, taking
extreme care to ensure that the small diameter vent pipe fits
inside the smaller opening in the rear of the unit. (See Figure
9). The larger diameter vent pipe must then slide over the
outside flange opening.
Warning: the heater will not function properly if these
connections are not tight and clean. Secure the unit to the
wall support bracket with the two screws provided.
Attach the Lighting Instructions to the back of the unit so that
they may be read when necessary. These instructions are for
current and future use. Make sure they remain accesible after
the unit is installed.
Connecting the gas supply
Connect the gas supply to the 3/8” (9.5 mm) pipe on the lower
part of the right side of the heater by using standard
connectors. Please refer to the cautionary remarks noted in the
beginning of this manual.
After connecting the gas supply to the gas control on the
heater, the connections must be checked thoroughly for
leaks. With the shut-off valve turned ON, but the gas control
knob on the heater OFF, apply liberal amounts of a soapy water
solution to all of the piping joints. A gas leak will cause
bubbles to form. Note any leaks in the piping system, then shut
off the gas at the shut-off valve, or at the gas meter or
propane/LP tank serving the building. Fix the leaking joint and
re-test the joints as directed above.
Mounting the furnace
Take off the cover by loosening the two screws at the bottom.
Pull the bottom away from the heater and lift it up off the tabs
on top.
Figure 9
Once the supply is checked and does not leak, place the cover
on the unit. See Figure 10. Be sure the foam packing has been
removed. Secure the cover with the two nuts at the bottom of
the unit which you had removed when unpacking.
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor's
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set the thermostat to the lowest setting.
3. Open the control access panel on the top right side of the unit.
4. Turn the gas control knob clockwise to the OFF position.
CONTROL KNOB
INDICATOR
1
2
3
5
GAS CONTROL KNOB
SHOWN IN OFF POSITION
5. Wait five (5) minutes to clear any gas. If you then smell gas,
STOP! Follow “B” in the safety information above in this
label. If you don´t smell gas, go to the next step.
6. Locate the red pushbutton Piezo igniter directly behind the
gas control knob.
PILOT THERMOCOUPLE
7. Turn the gas control knob counter clockwise to the
PILOT position. Depress the gas control knob and push in
the Piezo igniter several times, until the pilot is lit. The pilot
flame can be observed by looking down the inside of the
heater jacket. A small reflector on the right hand side near
4
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it; call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
the bottom should allow you to see if the pilot is lit. Removal
of the outer painted jacket of the heater will allow direct
visual observation of the pilot and burner.
8. Continue to depress the gas control knob for at least 30
seconds or until the pilot remains lit. When you release the
gas control knob, it should pop back up. Pilot should remain
lit.
- If the knob does not pop up when released, stop and
immediately call your service technician or gas supplier.
- If the pilot will not stay lit after several tries, turn the gas
control knob to the OFF position and call your service
technician or gas supplier.
9. Attention! Gas control knob has an INTERLOCK latching
device. When the pilot is initially lit and the safety magnet is
energized (pilot stays ON) the interlock latching device
becomes operative. If the gas control is turned to the OFF
position or gas flow to the appliance is shut off, the pilot
cannot be relighted until the safety magnet is de-energized
(approximately 60 seconds). There will be an audible “click”
when the safety magnet in the gas control is de-energized.
Pilot can now be relighted. Repeat steps 4 through 8.
10. Replace the front painted cover (if removed).
11. Turn the gas knob counter clockwise to the desired
temperature setting.
12. Close the control access door.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
2. Open the control access panel on the top right side of the unit.
3. Turn the gas knob clockwise to the OFF position. Do
not force.
4. Close the control access panel.
W ARNING: After turning off wait 5 minutes before trying
to relight.
Page 11MV1XX-2-0404
PILOT FLAME CHARACTERISTICS
The correct flame will be almost horizontal, blue and will
extend past the thermocouple 1/4" (6 mm). The flame will
surround the thermocouple just below the tip.
On propane (LP-gas) slight yellow might occur where the pilot
flame and burner flame meet.
Natural gas pilots require adjusting when the inlet pressure is
above 5" w.c. (1.25kPa). Turn adjustment screw clockwise to
reduce flame.
Propane (LP-gas) will not require adjusting.
MAIN BURNER FLAME CHARACTERISTICS
There will be a short blue inner flame with a much larger
lighter blue secondary flame. The burner flame may have a
yellow tip when hot. See the burner drawing showing the
approximate heights of each part of the flame. Dust in the
combustion air will produce an orange or red flame. Do not
mistake the orange or red flame for an improper yellow flame.
After use, cleaning may be required for the proper flame.
Pilot
Burner flame
Primary flame 1/4” (6 mm) to 1/2” (13 mm)
Secondary flame 4” (102 mm) to 6” (152 mm)
Flame must extend
past the thermocouple
Thermocouple
Figure 11
Figure 12
MAINTENANCE
The appliance should be inspected and cleaned before using
each year by a qualified service person.
Warning: the following instructions are designed to direct a
qualified technician through the proper periodic maintenance
and repair which may be required throughout the expected life
of this unit. NO attempt should be made by the homeowner
to perform these functions.
1. Remove the cover from the unit by removing the two nuts at
the bottom of the unit.
2. The gas supply should be turned OFF at the shut-off valve in
the supply piping leading to the appliance (if installed), or at
the gas meter or propane/ LP tank. The gas to the unit
should be disconnected so the unit can be removed from
the wall.
3. Remove the two screws which hold the unit to the wall
support plate and lift and pull the unit away from the wall.
4. Carefully examine the interior of the vent pipes, both large
and small diameter. If you notice any blockage or
obstruction, clean the pipes.
5. Look inside the openings of the rear of the unit and check for
any foreign materials. Remove any objects which may
block or obstruct the free flow of combustion and
ventilation air. You will only be able to see a portion of the
interior of the unit from this angle.
6. The main burner and pilot burner can be removed from the
unit for cleaning by first loosening the compression fittings
that supply gas to both the main burner and pilot. Note:
before removing either the pilot assembly or main burner
assembly be sure to have replacement gaskets on hand.
See Figure 13. After unscrewing the gas connection to the
burner and removing the compression nuts, unscrew the
thermocouple from the base of the pilot and remove it from
the pilot assembly. Remove the four screws which hold the
main burner/pilot plate in place, and withdraw the
burner/pilot from the unit. Check the burner/pilot for dirt,
lint, or a black powdery carbon deposit. If any is noted,
brush it off completely using a soft bristled brush, or blow it
Thermocouple
Screws that hold
the main burner/pilot
plate in place
Gas connection
to the burner
Figure 13
Page 12 MV1XX-2-0404
MAINTENANCE (cont.)
out. Do not attempt to pass anything through the pilot
orifice. Next, check the main burner for dirt, lint or carbon
deposits. Again, if any is noted, clean with a soft brush.
7. Inspect the interior of the combustion chamber for dirt, lint
or carbon deposits. If any are found, loosen them with a
long handled brush and remove the residue from the heater
with a vacuum cleaner.
8. In preparation for replacing the main burner/pilot, check
the condition of the gasket on the mounting plate. If the
gasket appears damaged or worn, replace ONLY with a
gasket available from Empire Comfort Systems Inc.,
whose address is at the bottom of this page. Install the
assembly in the heater and re-secure the assembly to the
heater chassis with the four screws removed in step 6
above. Note: verify that the left side of the main burner
is mounted on its support bracket. The burner should
be level.
9. Reconnect the main burner and pilot gas lines which were
disconnected in step 6 above. Reinstall the thermocouple
in the pilot bracket, inserting it fully into chamber before
tightening.
10. Replace the heater on the wall support bracket, taking
extreme care to ensure that the small diameter vent pipe is
firmly engaged with the vent outlet at the rear of the
heater. The large diameter vent pipe will slide over the
appropriate opening. Resecure the unit to the bracket with
the two screws removed earlier.
11. Reconnect the gas supply piping and REPEA T THE LEAK
TEST PROCEDURE. In addition, it will be necessary for
you to check the gas connections inside the unit for leaks.
After testing the gas connections to the unit, place the pilot
burner into operation by following the instructions found
in this manual or on the hanging tag behind the unit. Check
all joints to the pilot gas line with a soapy water
solution. Bubbles on any of the joints indicated a leak is
present and must be repaired. Turn OFF the gas to the unit
when performing any repairs to the gas piping system.
After the pilot lines are checked, turn the main burner ON
and again check all joints in the piping system for leaks
with soapy water. Repair any joints which indicate a leak
is present.
12. While the main burner is ON, check the pilot and burner
flames to see that they are burning a clean blue color. See
Figures 11 and 12 for an approximation of the correct
flame pattern. If your unit is not burning cleanly, or if you
are not sure, turn the unit OFF and contact the gas supplier
or call Empire Comfort Systems Inc..
Before completing your periodic maintenance checkout,
ensure that the appliance area is clear and free from
combustible materials, gasoline, and other flammable vapors
or liquids. Also check to see that the flow of combustion and
ventilation air around the vent cap on the outside of the
structure is not obstructed.
Note: verify proper operation after servicing.
HOW TO ORDER REPAIR PARTS
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts
through the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your
equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate
illustration and list. Be sure to give all this information . . .
Furnace Model Number Part Description
Furnace Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62222-0529
Page 13MV1XX-2-0404
PARTS LIST
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY
OR DEATH.
PART NAME
No.
Vent Assy. (6” to 12” / 152.4 to 304.8 mm)
1a
Vent Assy. (12” to 18” / 305 to 460 mm)
1b
Wall Support Plate
2
Combustion Chamber
3
Cover
4
Main Burner Assembly
5
Pilot Burner
6
Thermocouple
7
8a
Gas Control Nat. Gas
8b
Gas Control LP Gas
9
Piezo Igniter
10
Piezo Wire
11
Pilot Igniter Electrode
12
Gasket for Viewing Window
13
Mica for Viewing Window
14
Frame for Viewing Window
PART N° / MV 120
SD43019400
SD430194B0
SD44221800
SK00000047
SK00000050
SD44108300
SD44105800
SD44305500
SD44177000
SD44176900
SD44175800
SD44120800
SA00000263
SD44107002
SD44107100
SD44106900
PART N° / MV 130
SD43018500
SD430185B0
SD442202B0
SK00000048
SK00000051
SD44107500
SD44105800
SD44305500
SD44177000
SD44176900
SD44175800
SD44120800
SA00000263
SD44107002
SD44107100
SD44106900
PART N° / MV 145
SD43018400
SD430184B0
SD44326100
SK00000049
SK00000052
SD43107900
SD44105800
SD44305500
SD44177000
SD44176900
SD44175800
SD44120800
SA00000263
SD44107002
SD44107100
SD44106900
15
Mirror for Viewing Window
16
Pilot Tubing
17
Main Burner Tubing
18
Burner Support Plate
19
Pilot Burner Gasket
20
Main Burner Gasket
21a
Burner Orifice Natural
21b
Burner Orifice LP Gas
22a
Burner Orifices for 2000-4500 ft (6101370 m) altitude Nat. Gas
22b
Burner Orifices for 2000-4500 ft (6101370 m) altitude LP. Gas
23a
Pilot Burner Orifice Natural
23b
Pilot Burner Orifice LP Gas
24a
Minimum Rate Screw Nat.
24b
Minimum Rate Screw LPG
25
Gas Valve Connection Kit
SD44106801
SK00000053
SK00000054
SD44106100
SD44158001
SD44158102
SD44125400
SD44125700
SD443332A0
SD443332B0
SD44111300
SD44132400
SD44131900
SD44131600
SK00000055
SD44106801
SK00000053
SK00000054
SD44106100
SD44158001
SD44158102
SD44125500
SD44125200
SD443332C0
SD443332D0
SD44111300
SD44132400
SD44152900
SD44153000
SK00000055
SD44106801
SK00000053
SK00000054
SD44106100
SD44158001
SD44158102
SD443215A0
SD443215B0
SD443215C0
SD443215D0
SD44111300
SD44132400
SD44152900
SD44153000
SK00000055
Page 14
MV1XX-2-0404
PARTS VIEW
MV1XX-2-0404
Page 15
Loading...