Lang SXLG72-GCE Service Manual
Installation, Operation, Maintenance, & Troubleshooting
Model: SXLG72-GCE,
Electric Clamshell
Lang Manufacturing Company 6500 Merrill Creek Parkway Everett, WA 98203
Rev. # A Phone: 425-349-2400 Fax: 425-349-2733
WWW.LANGWORLD.COM © Copyright 2000
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE.
POST IN A PROMINENT LOCATION
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER
SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY
CONSULTING YOUR LOCAL GAS SUPPLIER. AS A MINIMUM,
TURN OFF THE GAS AND CALL YOUR GAS COMPANY AND
YOUR AUTHORIZED SERVICE AGENT. EVACUATE ALL
PERSONNEL FROM THE AREA.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ THE
INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT.
Model #: Purchased From:
Serial #: Location:
Date Purchased: Date Installed:
Purchase Order #: For Service, Call:
Clamshell is a registered trademark of Lang Manufacturing.
2
TABLE OF CONTENTS
CHAPTER PAGE
1. TABLE OF CONTENTS........................................................................3
2. READ FIRST ..........................................................................................4
3. EQUIPMENT DESCRIPTION...............................................................6
4. UNPACKING .........................................................................................8
5. INSTALLATION....................................................................................9
6. INITIAL START-UP ..............................................................................11
7. OPERATION ..........................................................................................12
8. MAINTENANCE & CLEANING..........................................................13
9. TROUBLESHOOTING..........................................................................16
10. PARTS LISTS.........................................................................................17
11. WIRING DIAGRAMS............................................................................18
12. WARRANTY..........................................................................................19
3
IMPORTANT READ FIRST IMPORTANT
CAUTION:
CAUTION:
CAUTION:
DANGER:
WARNING:
NOTICE:
NOTICE:
NOTICE:
CAUTION:
CAUTION:
THE UNIT IS EXTREMELY HEAVY. FOR SAFE
HANDLING, INSTALLER SHOULD OBTAIN HELP AS
NEEDED OR EMPLOY APPROPRIATE MATERIALS
HANDLING EQUIPMENT (SUCH AS A FORKLIFT,
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT
FROM THE SKID AND MOVE IT TO THE PLACE OF
INSTALLATION.
ANY STAND, COUNTER OR OTHER DEVICE ON
WHICH UNIT WILL BE LOCATED MUST BE
DESIGNED TO SUPPORT THE WEIGHT OF THE UNIT.
SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.
THIS APPLIANCE MUST BE GROUNDED AT THE
TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION
AND DEATH.
INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH
ELECTRICITY. IMPROPER INSTALLATION CAN
CAUSE INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.
The data plate is located behind access panel
between grease drawer and control panel. The unit
voltage, wattage, serial number, wire size, and
clearance specifications are on the data plate. This
information should be carefully read and understood
before proceeding with the installation.
The installation of any components such as a vent
hood, grease extractors, fire extinguisher systems,
must conform to their applicable national, state and
locally recognized installation standards.
During the first few hours of operation you may
notice a small amount of smoke coming off the unit,
and a faint odor from the smoke. This is normal for a
new unit and will disappear after the first few hours
of use.
ALWAYS KEEP THE AREA NEAR THE APPLIANCE
FREE FROM COMBUSTIBLE MATERIALS.
KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN
AND DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY
TO AVOID THE DANGER OF SLIPS OR FALLS.
4
IMPORTANT READ FIRST IMPORTANT
WARNING:
CAUTION:
NOTICE:
WARNING:
CAUTION:
KEEP WATER AND SOLUTIONS OUT OF CONTROLS.
NEVER SPRAY OR HOSE CONTROL CONSOLE,
ELECTRICAL CONNECTIONS, ETC.
MOST CLEANERS ARE HARMFUL TO THE SKIN,
EYES, MUCOUS MEMBRANES AND CLOTHING.
PRECAUTIONS SHOULD BE TAKEN TO WEAR
RUBBER GLOVES, GOGGLES OR FACE SHIELD
AND PROTECTIVE CLOTHING. CAREFULLY READ
THE WARNING AND FOLLOW THE DIRECTIONS ON
THE LABEL OF THE CLEANER TO BE USED.
Service on this or any other LANG equipment must
be performed by qualified personnel only. Consult
your authorized service agency directory or call the
factory at 1-800-224-LANG (5264), or
WWW.LANGWORLD.COM For the service agency
nearest you.
BOTH HIGH AND LOW VOLTAGES ARE PRESENT
INSIDE THIS APPLIANCE WHEN THE UNIT IS
PLUGGED/WIRED INTO A LIVE RECEPTACLE.
BEFORE REPLACING ANY PARTS, DISCONNECT
THE UNIT FROM THE ELECTRIC POWER SUPPLY.
USE OF ANY REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO
THE OPERATOR AND DAMAGE TO THE EQUIPMENT
AND WILL VOID ALL WARRANTIES.
5
EQUIPMENT DESCRIPTION
Lang Model: XL
Electric Clamshell
The Electric Clamshell consists of an electric griddle base and an electric hood.
Exterior
♦
Griddle
Griddle dimensions are 17” (43.18cm) high x 30” (76.20cm) deep x width is dependent
upon model number.
The sides, bottom, and rear wall are constructed of double wall stainless steel that allows
closer installation to combustible surfaces.
The griddle surface is made of 1” thick, highly polished steel that eliminates hot and
cold spots, recovery problems and warping, and ensures even heat to the edges of the
griddle.
♦
XL Hood
Hood dimensions (including griddle and legs) are 22¼” (55.88cm) high with hood
lowered, (44¾” [113.67cm] high with hood raised, 31½” (80cm) deep, x 24” (61cm)
wide.
The hood wrap is constructed of stainless steel.
There is a 3” clearance between griddle and hood.
Controls
♦
Griddle
Each twelve-inch section has a manual thermostat with a temperature range of 100°C to
450°C in 50° increments.
The thermostat is mounted in a fully enclosed, air-cooled compartment for protection
from heat and grease.
Each thermostat has a pilot light indicating when heating elements are energized. Light
shuts off when griddle reaches set temperature.
♦
XL Hood
The XL Hood has an “on/off” toggle switch located in the griddle base control area that
energizes the heater. A tilt switch is integrated in the top of the hood that activates the
heater to “full on” when lowered, standby when raised.
A “on/off” heat indicator lamp is located next to the “on/off” toggle switch.
6
Loading...