Lang ECCOP-AP User Manual

Download

Page 1

IL1519

ELECTRIC FULL SIZE

COMPUTERIZED

CONVECTION OVEN

ECOD-AP

ECOF-AP

Installation and

Operation

Instructions

2M-W488 Rev. D 2/5/09

ECOF-AP

Page 2

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

FOR YOUR SAFTEY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN

THE VICINTIY OF THIS OR ANY OTHER APPLIANCE.

POST IN PROMINENT LOCATION

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS

INFORMATION SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER.

AS A MINIMUM, TURN OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR

AUTHORIZED SERVICE AGENT. EVACUATE ALL PERSONNEL FROM THE AREA.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION,

OPERATION & MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR

SERVICING THIS EQUIPMENT.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

WARNING, TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE

CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE. REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

NOTICE

Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability.

Star reserves the right to change speci cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the speci cations contained in this sheet are subject to change without notice. While Star Manufacturing exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the speci cations. By using the information provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance. Please record the model number, serial number, voltage and purchase & Installation Information in the area below and have it ready when you call to ensure a faster service.

SAFETY SYMBOL

Model No.:

Serial No.:

Voltage:

1-Phase or 3 Phase:

Purchased From:

Location:

Purchase Date:

Installed Date:

Page 3

PROBLEMS, QUESTIONS or CONCERNS

Before you proceed consult you authorized Lang service agent directory

Call the Lang Technical Service & Parts Department at 1-800-807-9054.

TABLE OF CONTENTS

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Equipment Description .. Unpacking. .

Installation

Leg Installation ..

Leg Pad Adapter Installation .. . . . . . . . . . . . . . . . . . . .8

Stacking the Oven. Ventilation & Clearence.

Electrical Connection.. . . . . . . . . . . . . . . . . . . . . . . 11

Oven Voltage.

Initial Start-Up

Pre-Power On. .

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

General Operation & Programming

Control Panel..

Typical Operation Sequence.. . . . . . . . . . . . . . . . . . . 13

Hints & Suggestions.

Loading.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Maintenance

Cleaning.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

. . . . . . . . . . . . . . . . . . . . . . . .5

. . . . . . . . . . . . . . . . . . . . . . . . . .7

. . . . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . .10

. . . . . . . . . . . . . . . . . . . . . . . . . .12

. . . . . . . . . . . . . . . . . . . . . . . . . . 13

. . . . . . . . . . . . . . . . . . . . . . . .14

Troubleshooting Symptoms / Possible Causes / T

Wiring Diagram

208/240VAC.

220V/308VAC 4 Wire & 240V/415VAC 4 Wire.. . . . . . . . . . 18

380V/480VAC. . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Exploded View & Parts List . .

NOTICE Service

. . . . . . . . . . . . . . . . . . . . . . . . . . . .17

onthisoranyotherLangappliancemustbeperformedbyqualied

est. . . . . . . . . . . . . . . . .16

. . . . . . . . . . . . . . . . . . . .20-27

personnel only. Consult your Lang Authorized Service Agent Directory. You can call our toll free number 1-800-807-9054 or visit our website WWW.STAR-MFG.COM for the service agent nearest you.

Page 4

SPECIFICATIONS

15.1”

384mm

2.5”

54mm

ELECTRICAL

CONNECTION

2.5”

54mm

ELECTRICAL

CONNECTION

27.0”

687mm

0.9”

23mm

IL1520

Front View

Right Side View

Top View

Model Height x Width x Depth Clearance from Weight (without optional stand) combustible surface Installed Shipping Freight Class

ECOF 27.9” x 40.1” x 39.1” Side:6”, Back: 6”, Floor: 6” 380 lbs. 420lbs 70 708mm x 1019mm x 994mm (173 kg) (191 kg)

ECOD 27.9” x 40.1” x 46.0” Side:6”, Back: 6”, Floor: 6” 460 lbs. 500lbs 70 708mm x 1019mm x 1168mm (209 kg) (227 kg)

SPECIFICATIONS

Current Number Previous Model

208V

ECOD-AP ECCO-APXD-C

240V

Qty Hz.

1 2 1/3 23 1 GA. 8.8 8.8 5.5 4 GA. 1 1/3 11.5 6 GA. 4.2 3.7 3.7 10 GA. 2 1/3 23 2 GA. 7.8 7.8 7.3 4 GA.

ECOD-AP-480V ECCO-APXD-U 480V 1 60 3 11.5 15.6 15.6 10.5 14 GA.

VOLTS ACOven

208V

ECOF-AP ECCO-AP-C

240V

ECOF-AP-380V ECCO-AP-K 380V 1 50 3 11.5 19.7 19.7 12.2 12 GA. ECOF-AP-480V ECCO-AP-U 480V 1 60 3 11.5 15.6 15.6 10.5 14 GA.

ECOF-AP-M ECCO-AP-CM

ECOF-AP2/4FA ECCO-AP2/4FA 240/415V 1 50 3PH-4 WIRE 17.8 11.5 17.8 15.3 15.3 12 GA.

208V

240V

1 60 3.3 11.5 6 GA. 6.0 2.7 2.7 8 GA. 2 60 3.3 23 1 GA. 8.8 8.8 5.5 4 GA. 1 60 3.3 11.5 6 GA. 4.2 3.7 3.7 10 GA. 2 60 3.3 23 2 GA. 7.8 7.8 7.3 4 GA.

1 2 1/3 23 1 GA. 8.8 8.8 5.5 4 GA. 1 1/3 11.5 6 GA. 4.2 3.7 3.7 10 GA. 2 1/3 23 2 GA. 7.8 7.8 7.3 4 GA.

ECOF-AP380FA ECCO-AP-KFA 380V 1 50 3 11.5 19.7 19.7 12.2 12 GA. ECOF-AP440VM ECCO-AP-SM 440V 1 60 3 11.7 17.5 17.5 10.8 12 ECOF-AP480VM ECCO-AP-UM 480V 1 60 3 11.5 15.6 15.6 10.5 14

MOTOR

AMPS PHASE

50/60 3.3

AMPS 3PH /

NEUTRAL KW TOT.

SUPPLY

WIRE 1 PH L1 L2 L3

1/3 11.5 6 GA. 6.0 2.7 2.7 8 GA.

SUPPLY

WIRE 3 PH

Page 5

EQUIPMENT DESCRIPTION

Door Handle

Controls

Steam Valve

Cover

Motor Vent

Side Access

Panel

Blower Wheel

IL1521

Exterior Construction

The oven exterior dimensions are listed in the Specication Section. The Top, Front, Back, and Sides are constructed of heavy duty 430 stainless steel, with an attractive No. 4 nish.

The ovens simultaneous-opening heavy duty doors come standard with double pane windows.

The door handle is constructed of Stainless Steel and Phonolic Tubing.

The oven cavity is insulated with high temperature insulation for efciency and reduced heat loss.

Interior Construction

The ECOF oven cavity dimensions are 29” (72.5 cm) Wide, 20” (50.84 cm) High, 21” (53.38 cm) Deep..

The ECOD oven cavity dimensions are 29” (72.5 cm) Wide, 20” (50.84 cm) High, 27” (53.38 cm) Deep.

The interior of the oven is constructed of porcelainized stainless steel.

Operation

The ECOD-AP and ECOF-AP ovens are forced air convection ovens with a vented oven cavity.

The air is driven by a 1/3 HP fan motor.

Controls

Easy to use manual control knobs.

Solid state temperature sensing and controls.

Pulse and two-speed fan.

Technical

The ECOD-AP and ECOF-AP ovens come in voltages of 208/240V, 380V, 440V or 480V. .

This must be specied when ordering.

Floor space required is 48” (122.6 cm) wide, 44” (112.5 cm) deep.

The oven weighs 430 lbs.

NOTICE The data plate is on the back side of the oven above the power cord.

The oven voltage, wattage, serial number, wire size, and clearance

specicationsareonthedataplate.Thisinformationshould

be carefully read and understood before proceeding with the installation.

Page 6

CAUTION

UNPACKING

Receiving the Oven

Upon receipt, check for freight damage, both visible and concealed. .

Visible damage should be noted on the freight bill at the time of delivery and signed by the carrier’s agent. Concealed loss or damage means it does not become apparent until the merchandise has been unpacked. If concealed loss or damage is discovered upon unpacking, make a written request for

inspection by the carrier’s agent within 15 days of delivery. All packing .

material should be kept for inspection. Do not return damaged merchandise to Star Manufacturing Company. File your claim with the carrier.

Location

Prior to un-crating, move the oven as near to its intended location as practical. The crating will help protect the unit from the physical damage normally associated with moving it through hallways and doorways.

Un-crating

The oven will arrive completely assembled inside a wood frame and strapped to a skid. .

Cut the straps and remove the wood frame.

The oven can now be removed from the skid.

EACH UNIT WEIGHS 420 or 500 LBS. FOR SAFE HANDLING, INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE PLACE OF INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN WILL BE LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE OVEN.

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

Page 7

INSTALLATION

Rear

Support Assy

Front

Support Assy

Swivel Caster

Caster

Cardboard

IL1524

Stacked Units

Caster Sets

27” Leg Set (marine also)

27” Equipment Cart

6” Adj. Leg Sets

6” Adj. Bolt Down Leg Sets (marine only)

Accessory Options

Single Units

IL1525

Above: typical leg and caster installation. Below: accessory options, legs, casters & equipment carts sold

separately. Follow installation instructions with the each specic kit.

27” Leg Installation

With unit in position, fasten the two legs to the front corner pads then to the oven’s front corners

using the four 5/16 inch bolts provided in the leg kit. See leg pad adapter illustration to dermine

differences between front & rear support assemblies. .

Lift the oven onto its front legs and block the back up using one of the 27-inch legs set upside down in the center rear of the oven body. Install the third 27-inch leg onto the oven body on the control side rear. Gently lift the oven rear, remove the temporary support leg & install it on the last rear corner.

Leg Installation

Legs are available separately for both the single and double deck installations. Single deck installations require a 27-inch leg or

equipment cart. Double deck installations .

require 6-inch legs or casters. All these are available separately.

Place some cardboard on the ground and with assistance carefully lay the unit on its back. In stacked

The adjustable feet may be screwed in

or out as necessary to level the oven. A .

torpedo level placed on an oven rack will assist in leveling the oven.

Double-Stack Ovens

To install the 6-inch legs, adj. feet or casters on the lower unit, follow the Leg Pad instructions in the following section or in the instructions included with the leg pads.

Single Oven

To install 27” legs or cart to your unit, place the unit laying on its back onto a piece of cardborad. Be sure to read all instructions & follow the instructions provided with the kit.

Page 8

INSTALLATION cont.

E E E E

A A

D D D

OVEN BOTTOM

OVEN FRONT

IL1523

Above: Bottom on unit showing the placement of the leg adapters and their hole assignment.

labeled “B”. NOTE: There are two sets of “B” holes set at 90° from the each other. One set will create a left rear adapter and the other set will create a right rear adapter.

Install four 5/16-inch bolts through the caster base and the adapter holes labeled “B” then install .

5/16-inch nuts with lock washers and at washers.

Leg Pad Adapter

Identify the front and rear leg adapters (the front adapters have two threaded inserts, the rear has four). The leg adapters are included with each specic accessory kit.

Leg to Adapter Installation:

Install the leg’s threaded stud through the hole in the adapter labeled “C” with the bent ange of the adapter facing away from the leg.

Screw the 3/4-inch nut supplied in the

adapter kit onto the leg stud and tighten. .

Secure to oven using hardware provided.

Caster to Adapter Installation:

Place the swivel caster against the front leg

pad adapter with the ange of the adapter .

facing away from the caster.

Install the four 5/16 inch bolts through the caster base and the adapter holes labeled “A” then install the 5/16 inch nuts with washer and lock washers.

Place the rigid casters against the rear leg adapter with the ange of the adapter facing away from the caster.

Align the caster to the holes in the adapter

Adapter to Oven Installation:

Gently tip the oven onto its back. Place the front leg adapter into the front corers of the oven. The holes without the threaded inserts face the front of the oven and the ange on the adapter points toward the bottom of the oven.

The edge of the leg adapter with the threaded insert slips under the ange on the oven side, while the edge without the inserts sits on top of the threaded angle on the oven front.

Install two 3/8-inch bolts with lock washers and at washers through the front holes “D” in the leg adapter and into the threaded inserts on the oven.

Thread one 3/8-inch bolt with lock washer and at washer into the rear threaded hole labeled “E” on each of the leg adapters.

The forward threaded hole on the front leg adapter does not get a bolt installed.

Place the rear leg adapters into the rear corners of the oven so that the adapter is under the ange

of the oven side and back. . NOTE: If installing a caster place the adapter on the oven so that the casters roll forward.

Install for 3/8-inch bolts with lock washers and at washers through the holes labeled “E” in the ange of the oven and into the threaded inserts of the leg adapter.

Page 9

INSTALLATION cont.

Button Plugs

Bushing

Stacking Bolts

Upper Oven

Lower Oven

IL1526

Stacking the Ovens

Remove all the plug buttons from the top of the lower oven.

Remove the stacking kit from the oven compartment of one oven and install the 1 1/4-inch plastic bushing into the top of the lower oven.

Tip the top oven backwards and install two 3/8-inch socket head bolts, found in the stacking kit, into the two front leg holes that match the holes in the top of the lower oven. Install the socket head bolts with the heads of the bolt pointing away from the oven.

Lift the top oven and gently set on top of the lower oven so that the heads of the socket head bolts nest into the holes in the top of the lower oven.

NOTE: Each unit must have separate electrical connections

Page 10

INSTALLATION continued

Ventilation and Clearances

Standard minimum clearance from combustible construction is as follows.

4” from side

4” from back

6” from oor

• These ovens may be set directly, without legs, on a curbed base or non-combustible oor.

• If the oven is set without legs on a non-combustible oor or a curbed base, maintain a 4-inch back clearance.

• If the oven is set directly against a non-combustible back wall, maintain a 6-inch clearance to the oor.

• Do not install the oven closer than 4 inches from another oven on the right hand side (control panel side).

• Do not install the oven closer than 12 inches from an uncontrolled heat source (char broiler etc.) on the right side.

• Keep the area free & clear of combustible material, and do not obstruct the ow of combustion or ventilation air.

• The installation of any components such as a vent hood, grease extractors, and/or re extinguisher systems, must conform to the applicable nationally recognized installation standards.

NOTICE The installation of any components such as a vent hood, grease

extractors,reextinguishersystems,mustconformtotheir applicable National, State and locally recognized installation standards.

Page 11

INSTALLATION continued

208/240V

Transformer

208/240V

Jumper Location

Trim Piece

IL1593

Electrical Connection

The electrical connection must be made in accordance with local codes or in the absence of local codes with NFPA No. 70 latest edition (in Canada use: CSA STD. C22.1).

The electrical service entrance is provided by a 1 1/4-inch knockout in the bottom right front corner

of each oven, or at the oven back directly behind the control compartment. .

Grounding lugs are provided at both the front and rear service entrances.

The 208/240-volt oven is a dual voltage oven and is shipped from the factory as 208 volt. The oven must be eld converted to operate on a 240-volt power supply. To convert the oven to 240 volt,

remove the jumper wire located under the control compartment behind the bottom trim piece. .

As well as changing the transformer input wire to the 240V, color on the primary side of transformer (see illustration below).

With 380V, 440V & 480-volt installations check to be sure that the motor rotates in a clockwise direction as viewed from the front of the oven. To reverse the motor rotation, switch any two incoming power supply leads and recheck the rotation.

Supply wire size must be large enough to carry the amperage load for the number of ovens being

installed. Wire size information can be found on the oven DATA PLATE or in the specications .

section on page 4..

208/240V ovens can be installed on both single and three-phase supplies and is shipped from the

factory for three-phase. To phase the oven to match the power supply, follow the charts on the .

wiring diagram located at the back of the manual.

Certain units are provided with or can be purchased with a Cord & Plug kit . (Part number 9Q-ECOF-CK). This kit includes a 48” cord with a NEMA L15-50P plug and is

for 208/240V units ONLY. In stacked situations each units needs to have separate cord & plug assemblies.

WARNING

Oven Voltage

The Lang Model ECOF & ECOD ovens can be operated on 208, 240-volt (single or three phase), or 380/440/480V (three phase only) source. The Amp draw, KW rating, and phasing can be found in specication section of this manual.

THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED. FAILURE TO GROUND THE APPLIANCE COULD RESULT IN ELECTROCUTION AND DEATH.

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING. IMPROPER INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE CODES.

Left: 208/240V Dual Volatage units are shipped as

208V and must be eld converted to 240V.

Page 12

INITIAL START UP

Pre-Power On

After the oven is installed and connected to power, prior to turning on, verify the following:

• The doors open and close freely.

• All racks are in the oven correctly.

• All packing materials have been removed from the inside of the oven.

Power On

Once oven has been turned on verify that the blower wheel is spinning freely in a clockwise position and that the elements are heating properly.

Conﬁ rm that both thermostat knob and timer knob move freely and that the timer beeps..

NOTICE During the ﬁ rst few hours of operation you may notice a small

amount of smoke coming off the oven, and a faint odor from the smoke. This is normal for a new oven and will disappear after the ﬁ rst few hours of use.INITIAL START UP

Page 13

Vent Knob

Power

Light

Pulse Fan

Hi/Low Speed Fan

Temperature Control

Timer

IL1527

General Operation & Programming

Convection ovens constantly circulate air over and around the product. This strips away the thin layer of moisture and cool air from around the product allowing heat to penetrate more quickly.

Cooking times can be shortened and cooking temperatures can be reduced.

To convert standard deck oven recipes, reduce the temperatrue 50° degrees and the time by 25%. .

Make minor adjustments as necessary.

Always weigh your product. This will give you a more consistent size, color and quality.

Check the product near the end of the initial cooking.

Do not open the oven door during baking, as this will change the baking characteristics of the oven and make it .

difcult to determine a nal program.

If the product is overdone on the outside and underdone on the inside, reduce the baking temperature.

If the product is pulling away from the edge of the pan, the temperature is too high or the cooking time too long.

A convection oven is a mechanical piece of equipment. The same control settings will always give the same results. If the results vary, problems may be because of changes in the product preparation.

ECOF-AP / ECOD-AP Control Panel

The Control panel consists of the following items. . Detailed operational descriptions are given later this .

section.

Vent Knob: When open, allows moisture to escape the cooking chamber, allowing a dryer bake. (ex: crispy fries)

Power: Turns the oven on and off Pulse Fan:.

Pulse Setting: Fan will only turn ON, when the oven is

calling for heat.

Fan Setting: Fan is on continuously, speed is

determined by the Hi/Low switch.

Hi/Low Speed Fan: Dual speed switch. Toggles the fan

between high & low speed.

Temperature Control: Allows temperature to be set in

25°F increments from 140°F to 450°F

Timer: Electronic on-hour timer with .

continuous beeper,

Typical Operation Sequence

Action Result

Turn Power Switch to ON Adjust temperature, between

140°F & 450°F and allow 20 minutes for preheating

Open oven door and insert product, set timer up to 60 minutes.

Timer beeps continuously when done.

Control panel heat call light comes on.

Oven begins heating

Timer begins counting down.

Product should now be done.

Page 14

General Operation & Programming cont.

Hints & Suggestions

Convection ovens constantly circulate air over and around the product. This strips away the thin layer of moisture and cool air from around the product allowing heat to penetrate more quickly.

Cooking times can be shortened and cooking temperatures can be reduced.

To convert standard deck oven recipes, reduce the temperature 50 degrees and the time by 25%. Make minor adjustments as necessary.

The lower the oven temperature the more even the bake.

Always weigh your product. This will give you a more consistent size, color and quality.

Check the product near the end of the initial cooking cycle by turning on the oven light and looking through the oven door windows.

Do not open the oven doors during baking as this will change the baking characteristics of the oven and make it difcult to determine a nal program.

If the product is overdone on the outside and underdone on the inside, reduce the baking temperature.

If the product is pulling away from the edge of the pan, the temperature is too high or the cooking time too long.

The convection is a mechanical piece of equipment. The same control settings will always give the same results. If the results vary, problems may be because of product preparation.

Opening the vent will to allow mositure to escape the cooking chamber during part or all of the cooking process. This will allow a more crispy product, example: french fries, sh, crispy crusts. Close the vent for dough products like cinnamon rolls, breads. This is something to experiment with to determine what is best for your specic menu.

Here are some things to remember when loading your oven.

• When loading and unloading the oven, stage products and racks so the oven door is opened for the

least amount of time.

• Be sure that racks are level within the oven.

• Bent or warped pans can greatly affect the evenness of the cook or bake.

• If using baker’s parchment, be sure the parchment does not blow over the product. That will create

an uneven bake.

• Load each shelf evenly. Spaces should be maintained equally between the pan and oven walls, front

and back.

• Do not overload pan’s this will create an uneven bake.

• For best baking results, load the oven from the center out during random loading.

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM

COMBUSTIBLE MATERIALS.

CAUTION

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF

SPILLS OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR FALLS.

Page 15

MAINTENANCE

• Oven interiors should be wiped down daily and thoroughly cleaned weekly using warm water and mild detergent.

DO NOT use caustic cleaners.

• The appliance should be thoroughly checked at six-monthly intervals by a qualied technician . (heating unit, mechanical stability, corrosion...) with particular emphasis on all control and safety .

devices.

CLEANING

• Always start with a cold oven.

• The stainless exterior can easily be cleaned using stainless steel cleaner.

• Always follow the cleaner manufacturer’s instructions when using any cleaner.

• Care should be taken to prevent caustic cleaning compounds from coming in contact with the fan wheel.

• The oven racks, rack slides, may be cleaned outside the oven cavity using oven cleaner.

• Using any harsh chemicals will result in the removal of the ETC coating and etching of the . porcelain below it. The oven interior should only be cleaned using a mild soap and a non metal scouring pad. .

DO NOT use caustic cleaners.

• Always apply stainless steel cleaners when the oven is cold and rub in the direction of the metal’s grain.

KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY OR HOSE

CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.

WARNING

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS

MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO WEAR

CAUTION

RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE CLOTHING.

CAREFULLY READ THE WARNING AND FOLLOW THE DIRECTIONS ON THE

LABEL OF THE CLEANER TO BE USED.

NEVER LEAVE A CHLORINE SANITIZER IN CONTACT WITH STAINLESS STEEL

SURFACES LONGER THAN 10 MINUTES. LONGER CONTACT CAN CAUSE CORROSION.

Page 16

Troubleshooting

Symptoms & Possible Causes

The following are charts of Symptoms and Possible Causes to aid in diagnosing faults with your unit.

Refer to the symptoms column to locate the type of failure then to the Possible Cause for the items to be checked.

To test for a possible cause refer to test to identify test procedures. Test indicated with an “*” should be done by a Lang factory authorized service representative.

Symptoms Possible Cause

No power to cord outlet Oven unplugged from outlet

Power indicator is not lit

Oven will not heat

Oven motor will not run

Product burning

Product is under done

Failed Power cord or plug Failed power switch Failed indicator light Power Switch is not “ON” Failed Transformer Failed Probe Failed Circuit board Failed Contactor Failed Over-temperature Thermostat Failed Element Power Switch is not “ON” Failed Transformer Failed Contactor Failed Motor Product is cooked too long Failed Probe Failed Circuit board Product is not cooked long enough Failed Probe Failed Circuit board

Possible Cause Test

Product is cooked too long Failed Probe Check probe for proper resistance*

Failed Circuit board

Failed Transformer

Failed Contactor

Failed Motor Failed or disconnected safety

thermostat Failed Element

No test available, operational condition

Conrm that Circuit board is getting

correct voltage and putting out correct voltage*

Check both Primary and Secondary coils for correct voltage*

Remove the wires from the contactor coil and check for continuity across the contactor coil connection*

Ensure the contactor moveable points move freely up and down*

Conrm that motor is getting correct

voltage* Check across the thermostat

connectors for continuity*

Conrm that Elements are getting

correct voltage and have continuity*

NOTICE If an item on the list is followed by an asterisk (*), the work should be done by

a Lang factory authorized service representative.

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY

LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY INJURY

CAUTION

TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND WILL VOID ALL WARRANTIES.

NOTICE ServiceonthisoranyotherLangappliancemustbeperformedbyqualied

personnel only. Consult your Lang Authorized Service Agent Directory. You can call our toll free number 1-800-807-9054 or visit our website WWW.STAR-MFG.COM for the service agent nearest you.

BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS APPLIANCE

WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE RECEPTACLE. BEFORE

WARNING

REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER SUPPLY.

Page 17

HEAT

BUZZER

1 DECK

2 DECK

VOLTS

L1-L2 L2-L3 L3-L1 TOTAL L1 L2 L3 1 PH

KW AMPS

240

208

240

208

8.91

4.33

6.16

8.91

3.67

2.75

7.33

5.5

3.67

2.75

23.33

11.66

55.3

28.9

57.7

74.2

28.9

55.3

26.5

22.9

97.2

112

48.6

1,4,72 DECK 2,5,8 3.6 2,4,6,81,3,5,7

1,41 DECK

L2 L3

2 3

THREE PHASE

L1 L2

2,41,3

SINGLE PHASE

SERVICE CONNECTIONS

SECOND DECK

WIRING IDENTICAL

FIRST DECK

123

4 8

765

CIRCUIT BREAKERS

SECOND DECK

TERMINAL BLOCK

12 POLE

GROUND LUG

CONTACTOR

FROM MAIN

FUSES #2

DISC-STAT

HIGH-LIMIT

SWITCH

2-SPEED

HEAT LIGHT

24VAC

CONTROL

LIGHT

PULSE

TOP

24VAC

NC C NO

24VAC

TIMER

2345678

POSITION

SWITCH

RTD

543

-AP

16 BLU

15 BLK

14 RED

CONNECTOR

ARKLESS

30501-02

T-BLOCK

28 PRL

PRL

29 YEL

38 YEL

PULSE LAMP

PRL

26 YEL

46 BLK

XFMR

17 BLK

30701-05

41 BRN

40 BRN

21 WHT

19 RED

42 BRN

36 RED

47 YEL 48 YEL

31400-10

11 WHT

10 WHT

12 RED

BOTTOM

48 BLK

45 BLK

#1 TOP

45 BLK

13 WHT

18 RED

22 WHT

30203-16

30303-06

WHT

31800-01

32 BLU

7 BLU

6 WHT

5 RED

30700-06

59 BLU

58 BLU

RED

WHT

BLU

BLK

RED

WHT

BLU

11090-16

43 BRN

39 GRN

38 YEL

61 BLK

60 BLK

37 YEL

31601-07

63 BLK

30 GRN

31 BLU

29 YEL

27 GRN

30802-04

26 YEL

25 BLK

24 YEL

23 YEL

35 GRN

33 BLK

34 RED

40101-10

30304-16

30800-05

28 GRN

55 53 52 54

51 57 56 50

51 55 57 53 52 56 54 50

208V

JUMPER

T7-T4

NCC

4 4

FUSE

CONTACTOR

MAIN

24VAC

C D

240

LIGHT

240VAC

FROM MAIN CONTACTOR

BCD

DOOR SWITCH

OVEN LIGHTS

MOTOR

CIRCUIT BREAKERS

FIRST DECK

HEATING ELEMENT

TERMINALS

REAR VIEW

SWITCH

POWER

SWITCH

PULSE MODE

"HEAT"

FROM

REMOVE JUMPER FOR 240VAC

= WIRE NUT

3667W-240V2750W-208V

2750W-208V

2750W-3667W

3667W-240V

HIGH

30200-17

19 RED

10 RED

21 WHT

10 WHT

REVISION BLOCK

ECN NO.REV DESCRIPTION DR: DATEMFG ENG

-AP CONTROL

12 RED

10 RED

11 WHT

13 WHT

TOP

BOTTOM

CNTR

TIE WRAP

FUSE MOUNT

ECCO-226

FUSE HOLDER

30901-08

FUSE

30900-10

Model: ECCO-AP, 208-240VAC

2M-6111-109, Rev. B, 12/14/94

Page 18

28 GRN

30800-05

30304-16

40101-10

34 RED

33 BLK

35 GRN

23 YEL

24 YEL

25 BLK

26 YEL

30802-04

27 GRN

29 YEL

31 BLU

30 GRN

63 BLK

31601-07

37 YEL

60 BLK

61 BLK

38 YEL

39 GRN

43 BRN

11090-16

BLU

WHT

RED

BLK

BLU

WHT

RED

10 RED

19 RED

30700-06

5 RED 6 WHT 7 BLU

32 BLU

WHT

18 17

30303-06

30203-16

22 WHT

18 RED

13 WHT

45 BLK

48 BLK

12 RED

10 WHT

11 WHT

31400-10

48 YEL47 YEL

36 RED

42 BRN

19 RED

21 WHT

40 BRN

41 BRN

30701-05

30200-17

17 BLK

XFMR

46 BLK

26 YEL

PRL

30900-10

FUSE

CNTR

BOTTOM

TOP

PULSE LAMP

38 YEL

29 YEL

PRL

28 PRL

T-BLOCK

30501-02

ARKLESS

CONNECTOR

HIGH

14 RED

15 BLK

16 BLU

-AP

234

RTD

SWITCH

POSITION

9876543

TIMER

24VAC

NOCNC

24VAC

3667W-240V

2750W-3667W

2750W-208V

2750W-208V 3667W-240V

= WIRE NUT

TOP

FROM

PULSE

"HEAT"

LIGHT

PULSE MODE

CONTROL

24VAC

HEAT LIGHT

2-SPEED

SWITCH

CONTROL

-AP

HIGH-LIMIT

DISC-STAT

SWITCH

POWER

SWITCH

FUSES

FIRST DECK

CIRCUIT BREAKERS

31800-04

MOTOR

OVEN LIGHTS

DOOR SWITCH

FROM MAIN

CONTACTOR

GROUND LUG

12 POLE

TERMINAL BLOCK

SECOND DECK

CIRCUIT BREAKERS

567

SECOND DECK

WIRING IDENTICAL

FIRST DECK

FROM MAIN CONTACTOR

240VAC

LIGHT

240

24VAC

MAIN

CONTACTOR

FUSE

C NC

T7-T4

BUZZER

HEAT

50545253575551

55 53 52 54

51 57 56 50

HEATING ELEMENT

TERMINALS

REAR VIEW

FUSE MOUNT

ECCO-226

13 WHT

12 RED

10 RED

FUSE HOLDER

30901-08

11 WHT

TIE WRAP

DWG. NO:

SHEET

DESCRIPTION:

W/D ECCO-AP 220/308VAC 4 WIRE & 240/415VAC 4 WIRE

61111-173

REV:

VOLTS

L1-N L2-N L3-N TOTAL L1 L2 L3 Neutral

1 D E CK 220/380 3.10 3.10 3.10 9.30 14.1 14.1 14.1 14.1

1 D E CK 220/380 6.20 6.20 6.20 18.60 28.2 28.2 28.2 28.2

2 D E CK 240/415 3.70 3.70 3.70 11.10 15.4 15.4 15.4 15.4

2 D E CK 240/415 7.40 7.40 7.40 22.20 30.8 30.8 30.8 30.8

L1 L2 L3 N

1 D E CK 1 2 3 N

2 D E CK 1,4 2,5 3,6 N,N

KW AMPS

SERV ICE CONNE C TIO N S

Page 19

BRN

HI SPEED

T2 T3

LO SPEED

BLK

BLU

RED

BLACK

RED

BLUE

= WIRE NUT

2750W 480V

24 VAC

NOCNC

PULSE

TIMER

-AP

234

POSITION

SWITCH

BUZZER

9876543

FROM MAIN

CONTACTOR

FROM MAIN

FROM

"HEAT"

PULSE

SWITCH

CONTROL

24VAC

HEAT LIGHT

CIRCUIT BREAKERS

CONTROL

-AP

SWITCH

POWER

FUSES

SWITCH

RELAY

LIGHT

DISC-STAT

GROUND LUG

24 POLE

TERMINAL BLOCK

SECOND DECK

CIRCUIT BREAKERS

321

FIRST DECK

WIRING IDENTICAL

SECOND DECK

OVEN LIGHTS 240 VAC

480

LIGHT

CONTACTOR

MAIN

24VAC

FIRST DECK

MOTOR

FUSE

MOTOR

FUSE

DOOR SWITCH

C NC

T7-T4

2 SPEED SWITCH

RTD

HEAT

5054565253575551

55 53 52 54

51 57 56 50

HEATING ELEMENT

TERMINALS

REAR VIEW

DWG. NO:

SHEET

DESCRIPTION:

W/D ECCO-AP - 480,380 VAC

61111-110

REV:

L1-L2 L2-L3 L3-L1 TOTAL L1 L2 L3 1 PHA SE

1 DE CK 480 6.0 2.7 2.7 11.5 15.8 15.8 10.0 N/A

1 DE CK 380 6.0 2.7 2.7 11.5 19.7 19.7 17.2 N/A

2 DE CK 480 8.7 8.7 5.4 23.0 25.8 31.6 25.8 N/A

2 DE CK 380 8.7 8.7 5.4 23.0 23.0 39.5 32.1 N/A

L1 L2 L3 N/A N/A

1 DE CK 1 2 3 N/A N/A

2 DE CK 1-6 2-4 3-5 N/A N/A

AMPS

KW SERV ICE CONNECTIONS

3 P HAS E 1 P HAS E

VOLTS

Page 20

SK2366 Rev 4/21/2008

ECOF Main Assembly

16 1017

20 21

26 27 28

32 33

42 43

44 45

37 38

23 25

DetailA

Control Panel Assy

DetailB

Can Assembly

Page 21

PARTS LIST February 9, 2009, Rev. C

Model No: ECOF & ECOD Main Assembly

Commercial & Marine Full Size Electric Convection Oven

Key

Number

1 2C-20102-04 39 SCRW PHD ST 8-32X.5 PLTD ECOF-AP-380V, ECOF-AP-480V, ECOF-AP2/4FA, ECOF-AP380FA, ECOF-AP440VM, ECOF-AP480VM 2C-20102-04 40 SCRW PHD ST 8-32X.5 PLTD ECOF, ECOD 2 Q9-ECCO-230-1 1 TOP PANEL ASSEMBLY ECOF, ECOD 3 Q9-ECCO-176-2 1 BODY SPOTWELD STD. ECOF Q9-ECCO-177-3 1 BODY SPOTWELD DEEP ECOD 4 2P-70901-06 2 PLGBTNBLKPLSTC 5/8DP625 ECOF, ECOD 5 Q9-ECCO-176-4 1 STM VALVE COVER ECOF, ECOD 6 2C-20102-08 9 SCRW PHD ST 8-32X.375 ECOF, ECOD 2C-20102-08 13 SCRW PHD ST 8-32X.375 ECOF-AP-380V, ECOF-AP-480V, ECOF-AP2/4F ECOF-AP440VM, ECOF-AP480VM 7 Q9-60102-904 1 ACCESS COVER - ECCO/GCCO ECOF, ECOD 8 Q9-ECCO-124 1 TOP VENT SPOTWELD ECOF Q9-ECCO-124-1 1 ASSY - DEEP ECOD 9 Q9-ECCO-128 1 DAMPER BODY SPOTWELD ECOF, ECOD 10 2C-20103-02 3 SCRW SM PLT 10 X .5 PHLSL ECOF, ECOD 11 Q9-ECCO-182-3 1 BODY BACK S/S W/MOTOR ECOF, ECOD 12 Q9-ECCO-182-4 1 BODY BACK S/S COVER ECOF, ECOD 13 Q9-ECCO-133 1 DAMPER ROD B WELD ECOF, ECOD 14 Q9-ECO-437 1 DAMPER PIVOT ECOF, ECOD 15 2C-20602-02 2 TINNERMAN CLIP 1/4 ECOF, ECOD 16 2C-20301-20 1 NUT LOCK STOVER 1/4-20 ECOF, ECOD 17 Q9-ECCO-136 1 DAMPER BRACKET ANGLE ECOF, ECOD 18 2C-20104-41 6 SCRW MACH. 1/4-20X5/8 H/H ECOF, ECOD 19 Q9-ECCO-131 1 DAMPER ROD A WELD ECOF Q9-ECCO-131-1 1 DAMPER ROD WELD - DEEP ECOD 20 2C-20303-01 4 NUT HX SS 1/4-20 ECOF, ECOD 21 2R-70701-25 1 KNOB DAMPER BLACK PLAIN ECOF, ECOD 22 2E-31200-02 1 LUG GROUNDING UL APPROVED ECOF, ECOD 23 Q9-60102-99-1 1 BEARING BRACKET ASSY TOP ECOF, ECOD 24 2P-70201-07 2 BRNZ BR FLN 5/8IDX3/4ODX1 ECOF, ECOD 25 2C-20115-01 8 SCRW S/S 8-32X1/2 P/H S/T ECOF, ECOD 26 2C-20203-03 4 WSHR FLT SS 5/16 USS ECOF, ECOD 27 2C-20204-06 4 WSHR S/S 5/16 SPLIT LOCK ECOF, ECOD 28 2C-20111-07 4 SCRW SCKTHD 5/16-18X5/8 ECOF, ECOD 29 Q9-50312-43 1 RH DOOR ASSY E/GCCO ECOF, ECOD 29 Q9-50312-44 1 LH DOOR ASSY E/GCCO ECOF, ECOD 30 2C-71802-01 1 KEY WOODRUFF 3/16 X 5/8 ECOF, ECOD 31 2C-20201-15 5 WSHR FLT 960-C-1016 PLTD ECOF, ECOD 32 Q9-50312-67 1 PIVOT BEARING ASSY ECOF, ECOD 33 2P-73000-03 1 SST SPRKT40B11 5/8 BORE ECOF, ECOD 34 2C-20105-04 1 SCRW SET 1/4-20X1/2 ECOF, ECOD 35 2C-20301-07 1 NUT ACORN 1/4-20 PLTD ECOF, ECOD 36 2P-70201-06 2 BRNZBRFLN5/8IDX3/4ODX5/8 ECOF, ECOD 37 Q9-50312-41 1 BEARING BRACKET ASSY ECOF, ECOD 38 Q9-GCCO-185-4 2 HINGE BRACKET RETAINER ECOF, ECOD 39 2C-20115-01 4 SCRW S/S 8-32X1/2 P/H S/T PHDR ECOF, ECOD 40 2C-20111-07 4 SCRW SCKTHD 5/16-18X5/8 ECOF, ECOD 41 2C-20301-10 2 NUT HEX 6-32 PLTD ECOF, ECOD 42 2C-20102-12 2 SCRW PHD ST 10-32X3/8 ECOF, ECOD 43 Q9-ECCO-145-1 1 MICRO SWITCH BRACKET ECOF, ECOD 44 2E-30301-02 1 SWITCH, MICRO ECOF, ECOD 45 2C-20101-17 2 SCRW RND MS 6-32X1 PLTD ECOF, ECOD 46 2C-20104-50 2 SCRW HXHD 1/4-28X2-1/4 ECOF, ECOD 47 Y9-50312-05 1 HANDLE ASSY 1 HANDLE ECOF, ECOD 48 Q9-60102-1092 1 BOTTOM PANEL ECCO ECOF, ECOD

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Part

Number

Qty Per

Description

A, ECOF-AP380FA,

Star Manufacturing International, Inc.

Page 22

PARTS LIST June 30, 2008, Rev. C

Model No: ECOF & ECOD Main Assembly

Commercial & Marine Full Size Electric Convection Oven

Key

Number

49 Q9-ECCO-176-6 1 L/H BODY SIDE ECOF Q9-ECCO-177-1 1 L/H BODY SIDE - DEEP ECOD 50 2B-50200-93 2 RACK SLIDE 11 POS ECOF 2B-50200-94 2 RACK SLDE 11 POS E&GCCO-T ECOD 51 2B-50200-20 5 RACK ECCO/GCCO OVEN ECOF 2B-50200-31 5 RACK ECO DEEP OVEN ONLY ECOD

Part

Number

Qty Per

Description

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

Page 23

SK2353 Rev. A 4/25/08

Model: ECOF/D “ACCU-PLUS” Control Panel Assy Electric Full Size Convection Oven

32 6 7 119 14

16 19 20 24 26 28

Suggested Marine Parts Stocking

Detail A

Page 24

PARTS LIST June 30, 2008, Rev. C

Model No: ECOF-AP, & ECOD-AP CONTROLS PANEL

Commercial & Marine Full Size Electric Convection Oven

Key

Number

1 Q9-ECCOPAP-C 1 PANEL ECCO 208/240V ECOD-AP, ECOF-AP, ECOF-AP-M Q9-ECCOPAP-JFA 1 PANEL ECCO 380V ACCU-PLUS ECOF-AP2/4FA Q9-ECCOPAP-K 1 PANEL ECCO 380V ACCU-PLUS ECOF-AP-380V Q9-ECCOPAP-KFA 1 PANEL ECCO 380V ACCU-PLUS ECOF-AP380FA Q9-ECCOPAP-U 1 PANEL ECCO 480V ACCU-PLUS ECOD-AP-480V, ECOF-AP-380/480V, ECOF-

2 2R-70701-28 2R-70701-28 3 KNB BLK 1/4BUSH2SETSCW@90 ECCOPAP-JFA, ECCOPAP-KFA

3 2J-31601-01 1 PILOT LT 250V 6LEAD BLK ECCOPAP-JFA, ECCOPAP-KFA 2J-31601-07 2 PILOT LT 28V 6 LEAD WHT ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

4 2M-60301-100 1 PANEL LABEL- ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

2M-60301-120

5 Q9-50312-131 1 SPOT PANEL E & GCCO T & ECCOPAP-C, ECCOPAP-K, ECCOPAP-U Q9-50312-132 1 SPOT PANEL ECCO AP FAMOUS ECCOPAP-JFA, ECCOPAP-KFA

6 2E-30303-16 1 SWT TOG ON-ON BLK MOM ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

7 2E-30303-06 2 SWT TOG ON-ON DPDT BLK ECCOPAP-JFA, ECCOPAP-KFA 2E-30303-06 3 SWT TOG ON-ON DPDT BLK ECCOPAP-C, ECCOPAP-K, ECCOPAP-U 2E-30305-01 1 SWT INF 240V 15AMP ECCOPAP-JFA, ECCOPAP-KFA

8 2E-30304-16 1 CIR.BD.SWITCH 140’-450’F ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

9 Q9-30800-05-11 1 TIMER ELECTRIC 1-HR 24V ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

10 2C-20102-08 6 SCRW PHD ST 8-32X.375 ECCOPAP-C 2C-20102-08 10 SCRW PHD ST 8-32X.375 ECCOPAP-JFA, ECCOPAP-K, ECCOPAP-KFA,

11 2E-31400-07 1 XFORMR120-208-240/24V40VA ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-KFA 2E-31400-15 1 XFRMR 480/24VAC ECCOPAP-U 2E-31400-18 1 XFORM 380/24VAC 40VA U/L ECCOPAP-K

12 Q9-ECCO-285-2 1 SPOT COMPONENT MOUNT SII ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

13 2C-20102-05 2 SCRW HXHD ST 8-32X.75 ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

14 2E-30501-02 1 TRM STRP 3 POLE W/PUSH ON ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

15 2C-20102-12 2 SCRW PHD ST 10-32X3/8 ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

16 2E-30701-05 1 CONTC 2POLE 30A 24VAC P & ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

17 2K-70801-07 3 SPACER SUPPORT 1/2LG ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

18 2E-40101-19 1 CIRBD SI TEMP CNTRL NO ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

19 2E-30700-06 1 CONTC3POLE35A24VAC50/60HZ ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

20 2E-31800-01 4 CB 250V50A 1 POLE CRLNGSW ECCOPAP-C 2E-31800-04 1 CB 480V 50A 3 POLE ECCOPAP-JFA, ECCOPAP-K, ECCOPAP-KFA,

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Part

Number

Qty Per

2 KNB BLK 1/4BUSH2SETSCW@90 ECCOPAP-C, ECCOPAP-K, ECCOPAP-U

Description

AP440VM/480VM

ECCOPAP-U

LABEL SWITCH FOR R/S INF ECCOPAP-JFA, ECCOPAP-KFA

ECCOPAP-KFA, ECCOPAP-U

ECCOPAP-U

ECCOPAP-KFA, ECCOPAP-U

ECCOPAP-U

Star Manufacturing International, Inc.

Page 25

PARTS LIST June 30, 2008, Rev. C

Model No: ECOF-AP, & ECOD-AP CONTROLS PANEL

Commercial & Marine Full Size Electric Convection Oven

Key

Number

21 2C-20102-04 3 SCRW PHD ST 8-32X.5 PLTD ECCOPAP-JFA, ECCOPAP-K, ECCOPAP-KFA, 2C-20102-04 4 SCRW PHD ST 8-32X.5 PLTD ECCOPAP-C

22 Q9-ECCO-289 1 FUSE MOUNT - SII 208-240V ECCOPAP-C Q9-ECCO-289-1 1 FUSE MOUNT - SII 480V ECCOPAP-JFA, ECCOPAP-K, ECCOPAP-KFA,

2C-20101-26

24 2J-30802-04 1 BUZZER ELEC 24V AC PIEZIO ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

25 2C-20103-06 2 SCRW SM PLT 6 X 3/8 PHL ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

26 2E-30901-08 2 FUSE HLDR FOR SC FUSE ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

27 2C-20101-52 4 SCRW RHD MS 8-32 X 1/2 ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K,

28 2E-30900-10 2 FUSE 15AMP 300V (SC-15) ECCOPAP-C, ECCOPAP-JFA, ECCOPAP-K, NI 2E-30600-10 1 RELAY 2PDT 240V ECCOPAP-JFA, ECCOPAP-KFA

NI 2E-30705-03 1 CONTC 2-SPD MTR ABB ECCOPAP-K, ECCOPAP-KFA, ECCOPAP-U

Part

Number

2C-20101-26

Qty Per

4 SCRW MS PLT 6-32 X .25 ECCOPAP-JFA, ECCOPAP-K, ECCOPAP-KFA, 6

Description

ECCOPAP-U

SCRW MS PLT 6-32 X .25 ECCOPAP-C

ECCOPAP-KFA, ECCOPAP-U

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

Page 26

SK2367 Rev. A 6/03/08

ECOF: CAN & MOTOR ASSEMLBY

Detail B

168 28 33 34

Suggested Marine Parts Stocking

18 19 20

22 13

Page 27

PARTS LIST June 30, 2008, Rev. C

Model No: ECOF & ECOD CAN & MOTOR ASSEMBLY

Commercial & Marine Full Size Electric Convection Oven

Key

Number

1 2U-71500-05 1 BLOWER WHEEL ECCO/GCCO ECOF, ECOD 2 2C-20101-42 4 SCRW THD MS 10-24X2 PLTD ECOF, ECOD 3 2C-20301-09 2 NUT HEX 10-24 PLTD ECOF, ECOD 4 Q9-ECCO-168 1 MOTOR MOUNT WELD ECOF, ECOD 5 2C-20111-02 8 SCRW HXHD CAP 1/4-20X3/4 ECOF, ECOD 6 2H-ECCO-172 1 MOTOR INSULATION ECOF, ECOD 7 Q9-GCCO-166-2 1 SPACER - SAFETY STAT ECOF, ECOD 8 2T-30401-09 1 STAT FXD 500 DEG OPEN ECOF, ECOD 9 2C-20301-10 2 NUT HEX 6-32 PLTD ECOF, ECOD 10 Q9-GCCO-167 1 MOTOR SHIELD ECOF, ECOD 11 2C-20301-09 2 NUT HEX 10-24 PLTD ECOF, ECOD 12 2C-31900-03 1 CABLE STRAPS 3/16X7 ECOF, ECOD 13 2C-20103-02 4 SCRW SM PLT 10 X .5 PHLSL ECOF, ECOD 14 2K-70801-01 1 SNAP BUSH 7/16 SB437-5 ECOF, ECOD 15 2K-70801-04 1 SNAP BUSH 3/4 SB750-10 ECOF, ECOD 16 2U-30200-16 1 MTR 1/3HP 460V/1/60HZ 2SP ECOF-AP-480V, ECOF-AP440VM, ECOF-AP480VM, 2U-30200-17 1 MTR 1/3HP208/240V1PH2SPD ECOF-AP, ECOD-AP 2U-30200-53 1 MTR 1/3HP240/254V50HZ2SP ECOF-AP2/4FA 2U-30200-60 1 MTR 1/3HP380V1PH50HZ2SP ECOF-AP-380V, ECOF-AP380FA 17 2C-20118-01 4 SCRW CARRAGE PLT 5/16X.75 ECOF, ECOD 18 2C-20201-09 4 WSHR PLT 5/16 FLAT SAE ECOF, ECOD 19 2C-20202-08 4 WSHR PLT 5/16 LOCK SPLIT ECOF, ECOD 20 2C-20301-06 4 NUT HEX 5/16-18 PLTD ECOF, ECOD 21 Q9-ECCO-122 1 ELEMENT TOP COVER ECOF, ECOD 22 Q9-GCCO-115-1 1 MOTOR WIRE HOLDER ECOF, ECOD 23 Q9-ECCO-123 1 ELEMENT SIDE COVER ECOF, ECOD 24 2C-20102-04 40 SCRW PHD ST 8-32X.5 PLTD ECOF, ECOD 25 Q9-GCCO-247 1 PROBE HOLDER [ECCO & ECOF, ECOD 26 Q9-50312-34 1 PROBE COVER ECCO/GCCO ECOF, ECOD 27 2C-20109-04 4 SCRW THD MS SS 10-32X3/8 ECOF, ECOD 28 2N-11090-16 1 ELE ECCO OVN 208/240V11KW ECOF-AP, ECOF-AP2/4FA, ECOD-AP 2N-11090-18 1 ELMNT ECCO 480V 11KW ECOF-AP-480V, ECOF-AP480VM, ECOD-AP-480V 2N-1 ECOF-AP440VM 29 30 2C-20112-02 4 SCRWSHLDRTHUM 1/4-20X3/8 ECOF, ECOD 31 Q9-ECCO-163 1 REAR BAFFLE SPOTWELD ECOF, ECOD 32 Q9-GCCO-431 2 LIGHT RING - CORRECTIONAL ECOF, ECOD 33 2S-31603-04 2 LAMPS INC 250V 50W ECOF, ECOD 34 2E-31602-04 2 LAMP SKT SNAP-IN WHT ECOF, ECOD 35 2E-41100-08 1 SENSOR OVEN TEMP CONTROL ECOF, ECOD

Part

Number

1090-30 1 ELE 415 440V11KW ECOF-AP-380V, ECOF-AP380FA,

2C-20103-02 8 SCRW SM PLT 10 X .5 PHLSL ECOF, ECOD

Qty Per

Description

ECOD-AP-480V

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

Page 28

STAR MANUFACTURING

10 Sunnen Drive, St. Louis, MO 63143 U.S.A.

(800) 807-9054 (314) 781-2777

Parts & Service (800) 807-9054

www.star-mfg.com