Land Pride 4400NT User Manual 2

Retro Fit Gearbox Mount
Assembl y Instructions

Treker 4400NT & 4400ST Series

Before You Start

When you see this symbol, the subsequent
instructions and warnings are serious - follow

!

without exception. Your life and the lives of
others depend on it!

IMPORTANT: Before you begin, read these
instructions and check to be sure all partsand tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.

Your Land Pride Retro Fit Gearbox Mount is exclusively
designed for Land Pride 4400NT & 4400ST Trekers.
Please read these installation instructions and the
vehicle Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).

A separate Parts Manual for replacement parts can be
purchased from your dealer or downloaded free of
charge from our web site at www.landpride.com. Have
model and serial numbers handy when placing an order.

Manual No. 700-372M

Assembly Instructions

A detailed listing of parts for each accessory kit is
provided on page 5.Use the list that is for your Trekeras
a checklist to inventory parts received. Please contact
your local Land Pride dealer for any missing hardware.

Initial Preparations

1. Parkvehicleona flatsurface,movegearshiftleverto
forward, set par k brake, lock the cargo box in the up
position, turn off engine and remove ignition key.

2. Chock front and back of front tires to prevent the
vehicle from rolling.

3. See Operator’s Manual 700-108M forproper jacking
procedures. Follow all safety precautions in the
manual. Jack the back of the vehicle up to remove
pressure on the back right shock.

Refer to Figure 1:

4. Remove M14 hex nut and hex head cap screw (#1).

1

Manual Part Numbers:

• Operator’s Manual. . . . . . . . . . . . . . . . 700-108M

• Parts Manual . . . . . . . . . . . . . . . . . . . . 700-108P

General Information

These assembly instructions apply to the following Retro
Fit Gearbox Mounting Kits listed below:

700-373A NT Retro Fit Gearbox Mount
700-374A ST Retro Fit Gearbox Mount

Tools required:

•

Safety Glasses

• Work Gloves

• Center Punch

• Hammer

• Drill with 1/8" & 11/32" Drill Bits

• Torque wrench with required sockets listed below

• 7/16" Socket and box end or open end wrench

• 1/2" Socket and box end or open end wrench

• 9/16" Socket and box end or open end wrench

• M22 Socket and box end or open end wrench

• 3/16" Hex socket wrench

23676

Description

Figure 1

Refer to Figure 2:

5. Rotate shock back to access gearbox components.

23677

© Copyright 2005 Printed

6/14/05

Description

Figure 2

1

Assembly Instructions

Gearbox Removal

Refer to Figure 3:

1. Remove3/8" x 4 1/4" lg. upper shockbolt (#6), three
3/8" flat washers (#10), two fender washers (#18),
one H style motor mounts (# 16), gearbox mounting
spacer (#1) and 3/8" hex nut (#9). Discard all
removed parts.

2. Remove two 5/16" x 3/4" lg. hex head bolt (#5), lock
washer (#12) and flat washer (#11). Discard all
removed parts.

Land Pride

3. Remove Transfer case mount (#2) and discard.

4. Loosen 3/8" x 1" hex head cap screw (#7) at the
gearbox drive shaft connection (#13).

5. Loosen the two 1/4" hex socket cap screws (#8)
securing the gearbox coupling (#17) to the right
angle gearbox (#14).

6. Remove right angle gearbox (#14) from the vehicle.
Be careful not to loose keys (#3) and (#4).

23678

Gearbox Removal

Figure 3

Manual No. 700-372M 6/14/05

2

■