Land Pride 4220ST User Manual 3
Head Rest With Mounting Post
Assembl y Instructions
For 4220ST and 4420ST Trekers
Before You Start
When you see this symbol, the subsequent
instructions and warnings are serious - follow
!
without exception. Your life and the lives of
others depend on it!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
Your Head Rest With Mounting Post is exclusively
designed for the Heavy Duty 4-Post Accessory Bar.
Please read these installation instructions and your
Treker Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
A separate Parts Manual for replacement parts can be
purchasedfromyourdealeroravailablefreeofchargeat
www.landpride.com. Have model and serial numbers
handy when placing an order.
Manual Part Numbers:
• Operator’sManual (4220/4420 ST) . . . . 700-504M
• Parts Manual (4220/4420 ST) . . . . . . . . 700-504P
Manual No. 701-170M
General Information
These assembly instructions apply to the following Back
Screen and Head Rest accessories listed below:
701-169A HEAD REST WITH MOUNTING POST KIT
Tools required:
•
Safety Glasses
• Work Gloves
• Two 7/16" box end or open end wrenches
• Two 1/2" box end or open end wrenches
Assembly Instructions
A detailed listing of parts for this accessory kit is
provided on page 2. Use the list as a checklist to
inventory parts received. Please contact your local Land
Pride dealer for any missing hardware.
Initial Preparations
Before servicing the vehicle the following procedure
must be met to secure the vehicle:
1. Parkvehicleon a levelsurface.Don’t work under or
around a vehicle parked on an incline.
2. Set shift selector in Park.
3. Turn ignition switch off and remove switch key.
4. Chock front and back of a wheel to prevent the
vehicle from rolling.
Further Assistance
Your dealer wants you to be satisfied with your new
Treker. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
youmayhaveandthathe has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
© Copyright 2005 Printed
12/05/06
1
Assembly Instructions
Land Pride
Head Rest Assembly
Refer to Figure 1:
1. Behind the dr iver, attach bottom joint halves (#2) to
the 4-PostAccessory Bar lower cross member with
1/4"-20 x 2" GR5 hex head cap screw (#3), 2- flat
washers (#6) and nylock hex nut (#5). Do not tighten
nylock nuts.
2. Attach top joint halves (#2) to the 4-Post Accessory
Bar upper cross member with 1/4"-20 x 2" GR5 hex
head cap screws (#3), 2- flat washers (#6) and
nylock hex nuts (#5). Do not tighten nylock nuts.
3. Insert head rest mounting post (#1) into the bottom
joint halves and then into the top joint halves.
4. Adjust joint halves to center the head rest behindthe
driver’s head and tighten nylock nuts to 8 ft-lbs.
5. Locate a desirableheight that will protect the driver’s
head using two of the six holes in the head rest
mounting post (#1).
6. Attach head rests (#8) to the mounting post at that
height with 5/16"-18 x 1" GR5 hex cap screws (#4)
and flat washers (#7) as shown.
7. Tighten cap screws to 11 ft-lbs.
8. Repeat steps 1 through 7 for the passenger side.
24822
Head Rest Assembly
Figure 1
Kit No. 701-169A HEAD REST WITH MOUNTING POST KIT
Item Qty. Part No. Part Description
1 2 700-420H HEAD REST MOUNTING POST
2 8 700-500d JOINT PLATE
3 4 802-152C HHCS 1/4-20X2 GR5
4 4 802-738C HHCS 5/16-18 X 1 GR5
5 4 803-255C NUT HEX NYLOCK 1/4-20
6 8 804-007C WASHER FLAT 1/4 SAE PLT
7 2 804-036C WASHER FLAT 5/16 SAE PLT
8 2 840-179C HEAD REST WITH MOUNTING HARDWARE #4 & #7
1 701-170M MANUAL, HEAD REST WITH MOUNTING POST
Manual No. 701-170M 12/05/06
2
■
Loading...