Land Pride 4220ST User Manual 2
Back Screen & Head Rest
Assembl y Instructions
For 4220ST and 4420ST Trekers
Before You Start
When you see this symbol, the subsequent
instructions and warnings are serious - follow
!
without exception. Your life and the lives of
others depend on it!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
Your Back Screen & Head Rest is exclusively designed
for the Heavy Duty 4-Post Accessory Bar. Please read
these installation instructions and your Treker
Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
A separate Parts Manual for replacement parts can be
purchasedfromyourdealeroravailablefreeofchargeat
www.landpride.com. Have model and serial numbers
handy when placing an order.
Manual Part Numbers:
• Operator’sManual (4220/4420 ST) . . . . 700-504M
• Parts Manual (4220/4420 ST) . . . . . . . . 700-504P
Further Assistance
Manual No. 701-168M
General Information
These assembly instructions apply to the following Back
Screen and Head Rest accessories listed below:
701-167A BACKSCREEN, TREKER
701-165A HEADREST KIT, FOR BACKSCREEN
Tools required:
•
Safety Glasses
• Work Gloves
• Two 7/16" box end or open end wrenches
• Two 1/2" box end or open end wrenches
Assembly Instructions
A detailed listing of parts for each accessory kit is
provided on page 2. Use the list that is for your kit as a
checklist to inventory parts received. Please contact
your local Land Pride dealer for any missing hardware.
Initial Preparations
Before servicing the vehicle the following procedure
must be met to secure the vehicle:
1. Parkvehicleona levelsurface.Don’twork under or
around a vehicle parked on an incline.
2. Set shift selector in Park.
3. Turn ignition switch off and remove switch key.
4. Chock front and back of a wheel to prevent the
vehicle from rolling.
Your dealer wants you to be satisfied with your new
Treker. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
youmayhaveandthathe has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
© Copyright 2005 Printed
11/28/06
1
Assembly Instructions
Kit No. 701-167A BACKSCREEN, TREKER
Land Pride
Back Screen Assembly
Refer to Figure 1:
1. Install bottom joint halves (#1) to the 4-Post
Accessory Bar lower back cross member with
1/4"-20 x 2" GR5 hex head cap screw (#), 2- flat
washers (#5) and nylock hex nut (#4). Do not
tighten nylock nuts.
2. Install top joint halves (#1) to the 4-Post
Accessory Bar upper back cross member with
1/4"-20 x 2" GR5 hex head cap screws (#3), flat
washers (#5) and nylock hex nuts (#4). Do not
tighten nylock nuts.
3. Insert back screen (#2) into the bottom joint
halves and then into the top joint halves.
4. Adjust joint halves to center back screen on the
4-Post Accessory Bar.
5. Tighten nylock nuts to 8 ft-lbs.
Item Qty. Part No. Part Description
1 8 700-500D JOINT PLATE
2 1 700-514H WELDMENT, BACKSCREEN
3 4 802-152C HHCS 1/4-20X2 GR5
4 4 803-255C NUT HEX NYLOCK 1/4-20
5 8 804-007C WASHER FLAT 1/4 SAE PLT
8 990-246R EDGE TRIM 1/8X7/16 - 75 SERIES
1 701-168M MANUAL, ST TRUCK BACKSCREEN
24816
Back Screen Assembly
Figure 1
Kit No. 701-165A HEADREST KIT, FOR BACKSCREEN
Head Rest Assembly
Refer to Figure 2:
1. Locateadesirableheightandhorizontalposition
that will protect the driver and passenger heads.
2. Attach headrests (#4) to the back screen with
backingplates (#1), 5/16"-18 x 1" GR5 hex head
cap screws (#2) and flat washers (#3) as shown.
3. Tighten cap screws to 11 ft-lbs.
Item Qty. Part No. Part Description
1 2 700-523D PLATE, HEAD REST BACKING
2 4 802-738C HHCS 5/16-18X1 GR5 YELLOW DIE
3 4 804-036C WASHER FLAT 5/16 SAE PLT
4 2 840-179C HEADREST W/HARDWARE (Includes items 2 & 3)
1 701-168M MANUAL, ST TRUCK BACKSCREEN
Manual No. 701-168M 11/28/06
2
Headrest Assembly
Figure 2
24817
■
Loading...