Land Pride 322-215M User Manual
Table of Contents
Seed Bed Roller
Model SBR48, SBR60 & SBR72
Without Pull Hitch Option
With Pull Hitch Option
25763
25762
322-215M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
!
instructions andwarningsare serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2008 Printed
Cover photo may show optional equipment
not supplied with standard unit.
2/23/09
Table of Contents
Table of Contents
Land Pride
Important Safety Information . . . . . . . . . . .1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . .1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . .5
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . .5
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 5
Serial Number Plate . . . . . . . . . . . . . . . . . . . . . 5
Further Assistance . . . . . . . . . . . . . . . . . . . . . .6
Section 1: Assembly & Set-up . . . . . . . . .7
Tractor Requirements . . . . . . . . . . . . . . . . . . . . . .7
Three-Point Hook-up . . . . . . . . . . . . . . . . . . . . . 7
Pull Type Hook-Up . . . . . . . . . . . . . . . . . . . . . . 7
Three Point Hitch Assembly . . . . . . . . . . . . . . . . . . 7
Pull Type Hitch Assembly (Optional) . . . . . . . . . . . 8
Roller Scraper Assembly . . . . . . . . . . . . . . . . . . . . 8
3-Point Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pull-type Hook-up . . . . . . . . . . . . . . . . . . . . . . . . 10
Clevis Hook-up . . . . . . . . . . . . . . . . . . . . . . . . 10
Ball Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 2: Adjustments . . . . . . . . . . . . . .11
Scraper Bar Adjustment . . . . . . . . . . . . . . . . . . . . 11
Ball Hitch Swivel Adjustment . . . . . . . . . . . . . . . . 11
Section 3: Operating Procedures . . . . . .12
Operating Check List . . . . . . . . . . . . . . . . . . . . . .12
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Operating Instructions . . . . . . . . . . . . . . . . . . . . .13
Unhooking the Seed Bed Roller . . . . . . . . . . . . . .14
Storage Instructions . . . . . . . . . . . . . . . . . . . . . . .14
General Operating Instructions . . . . . . . . . . . . . .15
Section 4: Maintenance & Lubrication . .16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Roller Flange Bearings . . . . . . . . . . . . . . . . . .16
Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . .16
Section 5: Additional Equipment . . . . . . . 17
Additional Seeding Equipment . . . . . . . . . . . . . . .17
Disc Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Electric Spin Spreader . . . . . . . . . . . . . . . . . . .17
Drag Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Complete One Pass Seeding Application . . . .18
Section 6: Specifications & Capacities . 19
Section 7: Features and Benefits . . . . . .20
Section 8: Appendix . . . . . . . . . . . . . . . .21
Torque Values Chart For Common Bolt Size . . . .21
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
© Copyright 2008 All rights Reserved
Land Pride provides this publication “asis” without warranty ofany kind, either expressedor implied. While every precaution has beentaken in the preparationof this manual, Land
Pride assumesno responsibility forerrors oromissions. Neither isany liability assumedfor damagesresulting from theuse of theinformation contained herein.Land Pride reserves
the rightto revise andimprove itsproducts as it sees fit. This publicationdescribes the stateof this productat the time of its publication,and may notreflect the productin the future.
Land Pride isa registered trademark.
All other brands and product names are trademarksor registered trademarks of their respectiveholders.
Printed in the United States of America.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
Land Pride
▲
Table of Contents
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
▲ Operator should be familiar with
all functions of the unit.
▲ Operate implement from the
driver’s seat only.
▲ Make sure all guards and shields
are in place and secured before
operating the implement.
▲ Do not leave tractor or implement
unattended with engine running.
▲ Dismounting from a moving
tractor could cause serious injury
or death.
▲ Do not stand between the tractor
and implement during hitching.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Wear snug fitting clothing to avoid
entanglement with moving parts.
▲ Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
▲ Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
Look For The Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
!
DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
For Your Protection
▲ Thoroughly read and understand
the “SafetyLabel”section, read all
instructions noted on them.
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnelinvolved in
the operation, transport, maintenance and storage of
equipment.
!
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It mayalso
be used to alert against unsafe
practices.
!
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
Shutdown and Storage
▲ Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
▲ Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
2/23/09
OFF
REMO
VE
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
1
Table of Contents
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Use Safety
Lights and Devices
▲ Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
whendrivenonpublicroads.They
are difficult to see, especially at
night.
▲ Flashing warning lights and turn
signals are recommended
wheneverdriving on public roads.
Transport
Machinery Safely
▲ Comply with state and local laws.
▲ Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED.Nevertravelat a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
▲ Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
▲ Use the following maximum
speed - tow load weight ratios as
a guideline:
▲ 20 mph when weight is less than
or equal to the weight of tractor.
▲ 10 mph when weight is double
the weight of tractor.
▲ IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
Use A Safety Chain
▲ A safety chain will help control
drawn machinery should it
separate from the tractor
drawbar.
▲ Use a chain with the strength
rating equal to or greater than
the gross weight of the towed
machinery.
▲ Attach the chain to the tractor
drawbar support or other
specified anchor location. Allow
only enough slack in the chain
to permit turning.
▲ Do not use safety chain for
towing.
Practice Safe Maintenance
▲ Understand procedure beforedoing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower the implement to the ground,
put tractor in park, turn off engine,
and remove key before performing
maintenance.
▲ Allow implement to cool completely.
▲ Do not grease or oil implement
while it is in operation.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Remove buildup of grease, oil or
debris.
▲ Remove all tools and unused
parts from implement before
operation.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2
2/23/09
Land Pride
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
911
Wear
Protective Equipment
▲ Protectiveclothingandequipment
should be worn.
▲ Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
Avoid High
Pressure Fluids Hazard
▲ Escaping fluid underpressurecan
penetratetheskincausingserious
injury.
▲ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲ Use a piece of paper or
cardboard, NOT BODYPARTS, to
check for suspected leaks.
▲ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
▲ If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.
Keep Riders
Off Machinery
▲ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
Tire Safety
▲ Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
▲ When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
▲ When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
Handle
Chemicals Properly
▲ Protective clothing should be
worn.
▲ Handle all chemicals with care.
▲ Follow instructions on container
label.
▲ Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
▲ Inhaling smoke from any type of
chemical fire is a serious health
hazard.
▲ Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
2/23/09
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
3
Table of Contents
Important Safety Information
Safety Labels
Your Seed Bed Roller comes equipped with all safety
labels in place. They were designed to help you safely
operate your implement. Read and follow their
directions.
1. Keep all safety labels clean and legible.
2. Replace all damaged or missing labels. To order new
labels go to your nearest Land Pride dealer or visit our
dealer locator at landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Land Pride
4. Refer to this section for proper label placement.
To install new labels:
a. Clean the area the label is to be placed.
b. Spray soapy water on the surface where the label is to
be placed.
c. Peel backing from label.Pressfirmlyontothe surface.
d. Squeeze out air bubbles with the edge of a credit card.
Above Tongue
Below Tongue
848-148C
Negative Hitch Weight
Located below and above the tongue.
25762
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
4
2/23/09
Land Pride
Introduction
Introduction
Table of Contents
Land Pride welcomes you to the growing family of new
product owners. This Seed Bed Roller has been
designed with care and built by skilled workers using
quality materials. Proper assembly, maintenance and
safe operating practices will help you get years of
satisfactory use from the machine.
Application
The Land Pride SBR48, SBR60 and SBR72 Three-point
hitch or Pull-Type Seed Bed Rollers have uses and
applications in landscaping, sports field maintenance,
pasture maintenance, professional turf care, general
seeding and overseeding applications around home
sites, construction sites,horse paddocks, nurseries, sod
farms, and small farm or ranch operations. These Seed
Bed Rollers will break up smaller clumps and dirt clods,
whilepressing applied seedintofirm contact with thesoil
profile for greatly improved germination rates. The
notched profile of the rollers also develops a pattern of
uniformlyspaced mini-furrows that tendtoholdseed and
fertilizer in place. These small furrows also retain
essential moisture, and resist erosion from the wind and
the runoff from applied irrigation or rain.
The Seed Bed Roller also can also serve as the roller
packer attachment of Land Pride’s complimented
Seeder/Overseedersystem.Thissystemiscomprised of
a Land Pride Disc Harrow with a rear mounted Spin
Spreader and special hitch kit, a trailing 6’ x 4’ DRG06
Drag Harrow, and trailing Pull-type SBR72 Seed Bed
Roller. This componentized Seeder/Overseeder system
provides for one-pass groundcultivation and seedto soil
integration for applications on previously tilled soil,
existingpasture ground, largegrassyareas, reclamation
sites, or wild game food plots.
See“Section 6: Specifications & Capacities” on page
19 and “Section 7: Features andBenefits” on page20
for additional information and performance enhancing
options.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the directionthe machine will operate while in use
unless otherwise stated.
Definitions
NOTE: A special point of information that the
operator must be aware of before continuing.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
LandPridedealer. A dealer has trained personnel, repair
parts and equipment needed to service the Seed Bed
Roller.
The parts on your Seed Bed Roller have been specially
designedandshouldonlybe replaced with genuine Land
Pride parts. Therefore should your Seed Bed Roller
require replacement parts go to your Land Pride Dealer.
Serial Number Plate
For prompt service always use the serial number and
modelnumber when ordering partsfromyour Land Pride
dealer.Besuretoincludeyourserialandmodel numbers
incorrespondence also. Refer to Figure 1forthelocation
of your serial number plate.
Using This Manual
•
This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at thetime of printing. Some partsmay change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
www.landpride.com.
2/23/09
25763
Serial Number Plate Location
Figure 1
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
5
Table of Contents
Introduction
Further Assistance
Yourdealerwantsyou to be satisfied with your new Seed
Bed Roller. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership ser vice
manager making sure he is aware of any problems
youmay haveand that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
Land Pride
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
6
2/23/09
Loading...