Land Pride 313-308M User Manual
Table of Contents
Primary Seeders
PS2096 Series
20575
313-308M
Operator’s Manual
Read the Operator’s manual entirely.
When you see this symbol, the
subsequent instructions and
!
warnings are serious - follow without
exception. Your life and the lives of
others depend on it!
© Copyright 2008 Printed
Cover photo may show optional
equipment not supplied with
standard unit.
4/03/08
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . .1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . .7
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 7
Serial Number Plate . . . . . . . . . . . . . . . . . . . . .7
Further Assistance . . . . . . . . . . . . . . . . . . . . . .7
Section 1: Assembly & Set-Up (Standard) . . . . . . . 8
Pre-Assembly Checklist . . . . . . . . . . . . . . . . . . . . .8
Sling Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tire Track Remover Assembly . . . . . . . . . . . . . . . . 8
Section 2: Assembly & Set-Up (Optional) . . . . . . . . 9
Small Seeds Box (S/N 397503+) . . . . . . . . . . . . . . 9
Small Seeder Box assembly . . . . . . . . . . . . . . .9
Small Seeds Drive Assembly . . . . . . . . . . . . . 10
Small Seeds Box (S/N 397502-) . . . . . . . . . . . . . 11
Small Seeds Box Assembly . . . . . . . . . . . . . .11
Small Seeds Drive Assembly . . . . . . . . . . . . . 12
Pull Tongue Hook-Up . . . . . . . . . . . . . . . . . . . 13
Pull Tongue Disconnect . . . . . . . . . . . . . . . . . 13
Section 3: Operating . . . . . . . . . . . . . . . . . . . . . . . 14
General Description . . . . . . . . . . . . . . . . . . . . . . .14
Operating Check List . . . . . . . . . . . . . . . . . . . . . . 14
Seeder Preparation . . . . . . . . . . . . . . . . . . . . . . . 14
Tractor Requirements . . . . . . . . . . . . . . . . . . . . .14
Tractor 3-Point Hook-Up . . . . . . . . . . . . . . . . . . .14
Pull Tongue Hook-Up . . . . . . . . . . . . . . . . . . . . . 15
Seeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Roller Packing Wheels . . . . . . . . . . . . . . . . . . . . . 16
Land Pride
Section 4: Seeding Adjustments . . . . . . . . . . . . . . 17
Seed Rate Speed Change . . . . . . . . . . . . . . . . . .17
Main Seed Box . . . . . . . . . . . . . . . . . . . . . . . .17
Seeding Adjustments . . . . . . . . . . . . . . . . . . . . . .18
Main Seed Box . . . . . . . . . . . . . . . . . . . . . . . .18
Small Seeds Box Option . . . . . . . . . . . . . . . . .19
Seed Rate Charts . . . . . . . . . . . . . . . . . . . . . . . . .20
Seed Rate Charts (Metric) . . . . . . . . . . . . . . . . . .22
Seed Rate Charts (Small Seed Box Option) . . . . .24
Section 5: Maintenance & Lubrication . . . . . . . . .25
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Feed Cup Drive Shaft . . . . . . . . . . . . . . . . . . .25
Roller Bearings . . . . . . . . . . . . . . . . . . . . . . . .25
Roller Bearings . . . . . . . . . . . . . . . . . . . . . . . .26
Roller Chains . . . . . . . . . . . . . . . . . . . . . . . . . .26
Drive Sprocket Hanger Bearing (Zerk) . . . . . .26
Section 6: Specifications and Capacities . . . . . . .27
Section 7: Features & Benefits . . . . . . . . . . . . . . .28
Section 8: Troubleshooting . . . . . . . . . . . . . . . . . .29
Section 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . 30
Torque Values Chart For Common Bolt Size . . . .30
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
© Copyright2008All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land
Pride assumes no responsibility for errors oromissions.Neither is any liability assumed for damages resultingfrom the use of the informationcontained herein. Land Pride reserves
the right to revise and improveits productsas it sees fit. This publication describes the state ofthis product at the timeof its publication, and may not reflectthe product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
PS2096 Series Primary Seeders 313-308M
4/03/08
Land Pride
▲
Table of Contents
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
▲ Operator should be familiar with
all functions of the unit.
▲ Operate implement from the
driver’s seat only.
▲ Make sure all guards and shields
are in place and secured before
operating implement.
▲ Do not leave tractor or implement
unattended with engine running.
▲ Dismounting from a moving
tractor could cause serious injury
or death.
▲ Do not stand between tractor and
implement during hitching.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Wear snug fitting clothing to avoid
entanglement with moving parts.
▲ Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
▲ Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
Look For The Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
!
DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
For Your Protection
▲ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involvedin
the operation, transport, maintenance and storage of
equipment.
!
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
!
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
Shutdown and Storage
▲ Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
▲ Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
4/03/08
OFF
REMO
VE
PS2096 Series Primary Seeders 313-308M
1
Table of Contents
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Use Safety
Lights and Devices
▲ Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
when drivenon public roads. They
are difficult to see, especially at
night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
Use lights and devices provided
with implement.
Transport
Machinery Safely
▲ Comply with state and local laws.
▲ Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED.Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
▲ Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
▲ Use the following maximum
speed - tow load weight ratios as
a guideline:
20 mph when weight is less
than or equal to the weight of
tractor.
10 mph when weight is double
the weight of tractor.
▲ IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
Use A Safety Chain
▲ A safety chain will help control
drawn machinery should it
separate from the tractor
drawbar.
▲ Use a chain with the strength
rating equal to or greater than
the gross weight of the towed
machinery.
▲ Attach the chain to the tractor
drawbar support or other
specified anchor location. Allow
only enough slack in the chain to
permit turning.
▲ Do not use safety chain for
towing.
Practice Safe Maintenance
▲ Understand procedure before
doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower the implement to the
ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.
▲ Allow implement to cool
completely.
▲ Do not grease or oil implement
while it is in operation.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Remove buildup of grease, oil or
debris.
▲ Remove all tools and unused
parts from implement before
operation.
PS2096 Series Primary Seeders 313-308M
2
4/03/08
Land Pride
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
911
Wear
Protective Equipment
▲ Protective clothingand equipment
should be worn.
▲ Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
Avoid High
Pressure Fluids Hazard
▲ Escaping fluid under pressure can
penetratethe skincausing serious
injury.
▲ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲ Use a piece of paper or
cardboard, NOTBODYPARTS, to
check for suspected leaks.
▲ Wear protective glovesand safety
glasses or goggles when working
with hydraulic systems.
▲ If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.
Keep Riders
Off Machinery
▲ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
Handle
Chemicals Properly
▲ Protective clothing should be
worn.
▲ Handle all chemicals with care.
▲ Follow instructions on container
label.
▲ Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
▲ Inhaling smoke from any type of
chemical fire is a serious health
hazard.
▲ Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
4/03/08
PS2096 Series Primary Seeders 313-308M
3
Important Safety Information
Table of Contents
Land Pride
Safety Labels
Your Seeder comes equipped with all safety labels in place.
They were designed to help you safely operate your Seeder.
1. Read and follow label directions.
2. Keep all safety labels clean and legible.
3. Replace all damaged or missing labels.
4. Some new equipment installed during repair require safety
labels to be affixed to the replaced component as specified
by Land Pride. When ordering new components make sure
the correct safety labels are included in the request. To
order new labels go to your Land Pride dealer.
19635
5. Refer to this section for proper label placement. Install new
decals as follows
a. Clean the area on which the decal is to be placed.
b. Spray soapy water on the surface where the decal is to
be placed.
c. Peel backing from decal. Press firmly on surface,
being careful not to cause air bubbles under decal.
d. Squeeze out air bubbles with the edge of a credit card.
818-543C
DANGER: Guard Missing
(Beneath Guard)
PS2096 Series Primary Seeders 313-308M
4
19635
19635
838-111C
DANGER: Keep away,
Moving Parts
818-055C
SMV: Slow Moving Vehicle
4/03/08
Land Pride
Important Safety Information
Table of Contents
20579
20575
818-230C
Red Reflector
818-229C
Amber Reflector
20606
4/03/08
20606
818-543C
Small Grass Seed Option
DANGER: Guard Missing
(Beneath Guard)
838-111C
Small Grass Seed Option
DANGER: Keep away,
Moving Parts
PS2096 Series Primary Seeders 313-308M
5
Important Safety Information
Table of Contents
Land Pride
20593
20592
818-230C
Small Grass Seed Option
Red Reflector
818-055C
Small Grass Seed Option
SMV: Slow Moving Vehicle
PS2096 Series Primary Seeders 313-308M
6
4/03/08
Land Pride
Table of Contents
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
This Seeder has been designed with care and built by
skilled workers using quality materials. Proper assembly,
maintenance, and safeoperating practices will help you
get years of satisfactory use from the machine.
Application
The PS2096 Primary Seeder is perfect for wide open
landscape seeding and turf farms. The main seedboxcan
be equipped with our standard fluted seed cups and
agitation to seed most turf type grasses, as well as a
variety of other seeds from peasto alfalfa. Itis possibleto
seed two differenttypes of seed at different rates by
utilizing the optional Small Seeds Box. The Small Seeds
Box uses a smaller version of our fluted seed cup for
seeds such as alfalfa, clover and many other types of
small seeds. See “Section 7: Features & Benefits” on
page 28 for additional information.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Seeder.
The parts on your PS2096 Seeder have been specially
designed and should onlybe replaced with genuine Land
Pride parts. Therefore, should your Seeder require
replacement parts go to your Land Pride Dealer.
Serial Number Plate
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer.Be sureto include yourserial andmodel numbers in
correspondence also. Refer to Figure 1 for the location of
your serial number plate.
Using This Manual
•
This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• Toordera new Operator’s or PartsManual contact your
authorized dealer. Manuals can also be downloaded,
free-of-charge from our website at www.landpride.com
orprinted fromtheLand PrideService & SupportCenter
by your dealer.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
NOTE: A special point of information that the
operator must be aware of before continuing.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Owner Assistance
The WarrantyRegistration card should be filled out bythe
dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
20576
Serial Number Plate Location
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new
Seeder. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride
Service Department
P.O. Box 5060
Salina, KS 67402-5060
E-mail address
lpservicedept@landpride.com
4/03/08
PS2096 Series Primary Seeders 313-308M
7
Table of Contents
Section 1: Assembly & Set-Up (Standard)
Section 1: Assembly & Set-Up (Standard)
Pre-Assembly Checklist
Check Reference
All major frame components Operator’s
Manual
Fasteners and pins that were shipped
with the seeder.
NOTE: All hardware from the factory
has been installed in the location where
it will be used. If a part or fastener is
temporarily removed for assembly
reasons, remember where it goes.Keep
the parts separated.
Operator’s
Manual
Land Pride
Sling Bracket
Refer to Figure 1-1
The sling brackets allow points at each end to hook the
chain for lifting of the unit. When hooking the chain to the
sling brackets, be certain to either use a spreader bar on
the chain or use a long chain to preventbending the sling
brackets.
All working parts are moving freely,
bolts are tight and cotter pins are
spread.
If a pin, bolt or other part has been
removed, and you are unsure where it
is used, refer to the parts manual. Be
sure the part gets used in the correct
location. By double checking while you
assemble, you will lessen the chance of
using a bolt incorrectly that may be
needed later.
All grease fittings are in place and
lubricated.
Proper tension and alignment on all
drive chains.
Safety decals are correctly located and
legible. Replace if damaged.
Operator’s
Manual
Operator’s
Manual
Section 4
Page 25
Operator’s
Manual
Important
Safety
Information
Sling Bracket
Figure 1-1
Tire Track Remover Assembly
For shipping purposes the Tire Track Removers are
assembled 180 degrees from their operating position.
Refer to Figure 1-2
1. Remove Track Remover (#1).
2. FlipTrackRemoverover180degreesandreassemble
as shown with 1/2” u-bolt (#4), lockwasher (#3) and
nut (#2).
PS2096 Series Primary Seeders 313-308M
8
20589
Tire Track Remover
Figure 1-2
4/03/08
Land Pride
Table of Contents
Section 2: Assembly & Set-Up (Optional)
Section 2: Assembly & Set-Up (Optional)
Small Seeds Box (S/N 397503+)
Small Seeder Box assembly
1. Remove the eight bolts, lock washers and nuts that
areassembledin the front ofthe main box. Retaintwo
bolts,lock washersand nutsand use these toplug the
two holes in the front of the Small Seeds Box.
Refer to Figure 1-6:
2. Assemble the Small Seeds Box (#1) at the ends with
the four 5/16” bolts (#3), flat washers (#7), lock
washers (#6) and nuts (#5). Do not tighten until
spacers (step 3) are installed.
3. Alignthe fourboxspacers(#2) tothe innerholesofthe
Small Seeds Boxand themain box and assemble the
four longer 5/16” bolts (#4), flat washers (#7), lock
washers (#6) and nuts (#5).
4. Refer to Figure 1-4. Attach rubber seed tubes to
feeder cups with clamps provided and then into the
small holes inseeddropwithout clamps. Push rubber
hoses into the seed drop hole to removeany excess
slack.
Plug 2 Holes
Small Seeds Box Assembly
Figure 1-3
Rubber seed hoses
clamped to feeder cups
Insert rubber hoses
into seed drop holes
Small Seeds Tube Assembly
Figure 1-4
20587
20596
4/03/08
PS2096 Series Primary Seeders 313-308M
9
Loading...