LANBO LB80BC, LW28D, LW46D, LW52S, LB36BD User Manual

...
Page 1

LANBO

USER MANUAL

FOR MODEL:

LW28D/LW46D/LW72D/LW142D/LW165D/LW306D
LB36BD/LW3370B
LW33S/LW52S/LW155S/LW177S/LW321S
LW133DD/LW162DD/LW144T
1
Page 2
Dear User,
1. After the new appliance arrived, please leave it alone for about 12 hours
2. Set the suitable temperature for your wine:
Congratulations to you to get a new appliance and also thank you for
purchasing from us.
Here are some warm tips for you to use the product better.
Before use:
before connecting with power.
Merlot, Shiraz and Cabernet Sauvignon - Anywhere from 64-66
Chardonnay and Chablis - Between 48-52
Pinot Noir - 60-64
Dessert Wines, Sparkling wine or Champagne - 40
Pinot Grigio and Sauvignon Blanc - 45-48
When using:
1.Please make sure the door is closed well and don’t open and closed the
door too often to disturb the storage environment of the wine.
2.Put every wine bottle a suitable place and try not to move them until you
want to enjoy them. Stillness is essential in allowing wines to age well and
continue to drink beautifully.
Register your product:
LANBO promises to supply 12 months whole parts and 36 months compressor
warranty. Register your product on LANBO’s official website will get a 12
months warranty extension and priority customer support.
2
Page 3
Customer service:
If you need our help, please send email to service@lanboappliances.com .
Our customer service team are always here to help you.
Thanks for all your trust and support!
3
Page 4

Catalogue

Important Safety Notes------------------------------------------------ 5
Structures -----------------------------------------------------------------7
Installation ---------------------------------------------------------------13
Operation Instruction --------------------------------------------------14
Care and Maintenance ------------------------------------------------25
Troubleshooting ---------------------------------------------------------27
Data Parameters --------------------------------------------------------28
WARRANTY INFORMATION --------------------------------------- 31
4
Page 5
1. Important Safety Notes:
Warnings
To reduce the risk of fire, electrical shock, or injury when
using your appliance, follow these basic precautions:
Read all instructions before using the wine cooler.
Do keep the children away from the wine cooler. Never allow children to
operate, play with, or crawl inside the appliance.
Never clean appliance parts with flammable fluids. The fumes can create a
fire hazard or explosion.
While wine cooler stops working, please call our after-sell service
department or other related technicians to check and repair. Never do it by
yourself in case of accident.
Once the power cord is damaged, find a professional technician or
electrician to change a new one. Never do it by yourself or continue to use
so as to avoid danger.
Do make sure that the plug is pulled while cleaning, moving or repairing.
Keep ventilation openings in the appliance enclosure clear of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting
process other than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage compartments of
the appliance unless they are of the type recommended by the
manufacturer.
-Save these instructions-
In order to avoid damage of door seal, please make sure the door totally opened while
Place the cooler closed to power socket.
Notes
pulling out the movable shelves.
5
Page 6
Once the cooler is stored with wines, please do not move it again.
Make sure the cooler placed in proper place in order to avoid that the compressor in the
back could be easily touched.
Do not start the wine cooler too frequently. The interval should be at least 5 minutes.
Before you throw away your old wine cooler: Take off the door. Leave the shelves in
If the wine cooler with R600a, flammable and explosive articles should not be put in or near
This appliance can be used by children aged from 8 years and above and persons with
Children shall not play with the appliance. Cleaning and user maintenance shall not be
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
Please keep this use manual carefully, if you lost the use manual,
The instructions shall include the substance of the following: This
Parameters and appearance of the product may be different from the manual, does not
original place so that children may not easily climb inside.
the cabinet, to avoid the fire or explosion.
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.
made by children without supervision.
similarly qualified persons in order to avoid a hazard.
please contact with us at service@lanboappliances.com
appliance is intended to be used in household and similar applications
such as:
Staff kitchen areas in shops, offices and other working environments;
Farm houses and by clients in hotels, motels and other residential
type environments;
Bed and breakfast type environments;
Catering and similar non-retail applications.
affect the normal use of the product.
6
Page 7
7
2. Structures
1.LW33S/LW52S/LW155S/LW177S/LW321S structure diagram
(1) Control panel (2) The fan of evaporator (3) Carbon filter (4) Sensor
(5) Full wooden shelf (6) Heating fan (7) Small wooden shelf (8) Prevent
fall device of the door (9) Adjustable feet (10) Upper hinge (11) Glass
door with lock (12) Door gasket (13) Handle (14) Lock hook (15) Lower
hinge (16)The front vent
Page 8
8
2. LW28D/LW46D/LW72D/LW142D/LW165D/LW306D structure
diagram:
(1) Control panel (2) Carbon filter (3) The fan of evaporator (4) The upper
sensor (5) Full wooden shelf (6) Baffle plate (7) Heating fan (8) The lower
sensor (9) Small wooden shelf (10) Prevent fall device of the door
(11) Adjustable feet (12)Upper hinge (13) Glass door with lock (14) Door gasket
(15) Handle (16) Lock hook (17) Lower hinge (18)The front vent
Page 9
9
3. LW133DD/LW162DD structure diagram
(1) Control panel (2) The fan of evaporator and heater (3) Carbon filter (4) Full
wooden shelf (5) The upper sensor (6) Baffle plate (7) The fan of evaporator
and heater (8) The lower sensor (9) Small wooden shelf (10) Prevent fall
device of the door (11) Lock hook (12)Upper hinge (13) Glass door with
handle/gasket (14) Middle hinge (15) Glass door with handle/gasket (16) Lower
hinge (17) Adjustable feet (18) The front vent
Page 10
10
4. LW144T structure diagram
(1) Upper control panel (2) Carbon filter (3) Full wooden shelf (4) The upper
sensor (5) Middle control panel (6) Middle fan (7) Full wooden shelf (8) The
middle sensor (9) Baffle plate (10) The back air-duct Board (11) The lower
sensor (12) Small wooden shelf (13) Prevent fall device of the door
(14) Adjustable feet (15) Upper hinge (16) Glass door with lock (17) Door
gasket (18) Handle (19) Lock hook (20) Lower hinge (21) The front vent
Page 11
11
5.LB80BC /LB148BC structure diagram
(1) Control panel (2) Wire shelf (3) Glass shelf (4) Small wooden shelf
(5) Lock hook (6) Prevent fall device of the door (7) Adjustable feet (8) Upper
hinge (9) Glass door with lock/ gasket (10) Handle (11) Lower hinge
(12) The front vent
Page 12
12
6.LB36BD/LW3370B structure diagram:
(1)Left upper hinge (2) Left Control panel (3) Big wire shelf with wooden
cover (4) Left glass door with lock / gasket & handle (5) Small wire shelf with
wooden cover (6) Left lower supporter of the door (7) The front vent
(8) Right upper hinge (9) Right Control panel (10) Wire shelf (11) Left
glass door with lock / gasket & handle (12) Wire basket (13) Right lower
supporter of the door (14) Adjustable feet (15) Lock hook
Page 13
3.Installation
Before Using Your Wine Cooler / Beverage Cooler
Remove the exterior and interior packing.
Before connecting the wine cooler / beverage cooler to the power source,
Clean the interior surface with lukewarm water with a soft cloth.
The cooler is specially designed for wine storage, please do not put in
Installation:
The cooler should be placed independently so as to make sure good heat
Place your wine cooler / beverage cooler on a floor that is strong enough to
Locate the wine cooler / beverage cooler away from direct sunlight and sources
Avoid locating the unit in moist areas.
Plug in the proper power socket. Make sure that the shape and voltage of the
let it stand upright for approximately 12 hours. This will reduce the
possibility of a malfunction in the cooling system from handling during
transportation.
other goods.
dissipation. The back of the cooler should be away from the wall 10cm at
minimum.
support it when it is fully loaded. To level your wine cooler, adjust the front
leveling leg at the bottom of the wine cooler.
of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic
coating and heat sources may increase electrical consumption. Extreme cold
ambient temperatures may also cause the unit not to perform properly.
socket is consistent with the nameplate on the back of the cooler.
13
Page 14
5. Operation Instruction
4.1 Control Panel Below (LW33S/LW52S/LW155S/LW177S/
Display Windows
Button Operation
LW321S/LB80BC/LB148BC)
· RUN light:Indicator light of compressor working. While the compressor operating,
the red light is on. While it stops operating, the red light is off.
·SETTING:Display of the temperature you set. The range of temperature setting is
0~37or 32~99.
·CHAMBER:Display of the actual temperature inside the cabinet; The range is
0~37or 32~99.
·/lightWhen the light is on, it indicates Celsius temperature; When the
light is on, it indicates Fahrenheit temperature.
·SET Button:Temperature setting button; Once you press the button, the
temperature increased 1or 1. Detail temperature setting range as
following:
For LB80BC is between: 3~18or 37~64;
For LB148BC is between: 1~18or 34~64;
For LW33S/LW52S/LW155S/LW177S/LW321S is between:5~18or 41~64.
·LIGHT Button:Cabinet light control button; Note: Once the light is turned on, it will
automatically off after 10 minutes all out of protecting the wines inside.
·/Button:Celsius and Fahrenheit conversion button;
·ON/OFF button:Power on and off button; Press the button for 3 seconds, it starts;
press it 3 seconds again, it stops.
14
Page 15
4.2 Control Panel Below(LB36BD)
Display Windows
Button Operation
· RUN light:Indicator light of compressor working. While the compressor operating,
the red light is on. While it stops operating, the red light is off.
·CHAMBERDisplay of the setting and actual temperature inside the cabinet; The
range is 0~37or 32~99.
·/lightWhen the light is on, it indicates Celsius temperature; When the
light is on, it indicates Fahrenheit temperature.
·” “–” Button Temperature setting button; Once you press “” button, the
temperature increase 1or 1; if you want to decrease the temperature, press
the “-” button, the temperature decreased 1or 1each time.
Detail temperature setting range as following:
5~18or 41~64for the left zone, 4~10or 39~50for the right zone;
·LIGHT ButtonCabinet light control button; Note: Once the light is turned on, it will
automatically off after 10 minutes all out of protecting the wines inside.
·/ButtonCelsius and Fahrenheit conversion button;
·ON/OFF buttonPower on and off button; Press the button for 3 seconds, it starts;
press it 3 seconds again, it stops.
15
Page 16
4.3 Control Panel Below(LW3370B/LW133DD/LW162DD)
Display Windows
Button Operation
·CHAMBERDisplay of the setting and actual temperature inside the cabinet; The
range is 0~37or 32~99.
·/lightWhen the light is on, it indicates Celsius temperature; When the
light is on, it indicates Fahrenheit temperature.
·” “–” Button Temperature setting button; Once you press “” button, the
temperature increase 1or 1; if you want to decrease the temperature, press
the “-” button, the temperature decreased 1or 1each time.
Detail temperature setting range as following:
For LW3370B is between: 5~18or 41~64for the left zone, 4~10or
39~50for the right zone.
For LW133DD/LW162DD is between: 5~18or 41~64both for upper and
lower zone.
·LIGHT ButtonCabinet light control button; Note: Once the light is turned on, it will
automatically off after 10 minutes all out of protecting the wines inside.
·/ButtonCelsius and Fahrenheit conversion button;
·ON/OFF buttonPower on and off button; Press the button for 3 seconds, it starts;
press it 3 seconds again, it stops.
16
Page 17

4.4 Control Panel Below ( only for model LW144T):

Display Windows
Button Operation
Display Windows
(Upper Control Panel)
CHAMBER: Display of the actual temperature of the upper chamber. The range is
0~37or 32~99.
“+” “–” Button: Temperature setting button. Each time you press the button “+”
button the temperature increased 1or 1. Or press “-” button the
temperature decreased 1or 1; Setting range is between 5~22or
41~72of upper zone.

(Middle and Lower Control Panel)

MIDDLE CHAMBERDisplay of the actual temperature of the middle chamber.
The range is 0~37or 32~99.
LOWER CHAMBERDisplay of the actual temperature of the lower chamber;
The range is 0~37or 32~99.
· /lightWhen the light is on, it indicates Celsius temperature; When the
light is on, it indicates Fahrenheit temperature.
17
Page 18
Button Operation
“+” “–” Button: Temperature setting button; If you need setting the temperature
of middle chamber, press the button one time, the screen of middle chamber
will be flashing, then press “+” or “-” to set the temperature of middle chamber,
setting range is between 5~12 or 41 ~54 . If you need setting the
temperature of lower chamber, press the button two times, the screen of
lower chamber will be flashing, press “+” or “-” to set the temperature of lower
chamber, setting range is between 12~22or 54~72℉.
· LIGHT Button:Cabinet light control button; Note: Once the light is turned on, it will
automatically off after 10 minutes all out of protecting the wines inside.
· ON/OFF button:Power on and off button; Press the button for 3 seconds, it starts;
press it 3 seconds again, it stops.
18
Page 19

4.5 Control Panel Below (LW28D/LW46D/LW72D/LW142D/

Display Windows
Button Operation
LW165D/LW306D):
· RUN light:Indicator light of compressor working. While the compressor operating,
the red light is on. While it stops operating, the red light is off.
· UPPER CHAMBERDisplay of the actual temperature of the upper chamber. The
range is 0~37or 32~99.
· LOWER CHAMBERDisplay of the actual temperature of the lower chamber; The
range is 0~37or 32~99.
· /lightWhen the light is on, it indicates Celsius temperature; When the
light is on, it indicates Fahrenheit temperature.
· SET ButtonTemperature setting button; Once you press the button, the
temperature increased 1or 1. Detail temperature setting range as
following:
For LW28D/LW46D/LW72D/LW142D/LW165D/LW306D is between:
5~12or 41~54for upper zone, 12~18or 54~64for lower zone;
· LIGHT Button:Cabinet light control button; Note: Once the light is turned on, it will
automatically off after 10 minutes all out of protecting the wines inside.
· /ButtonCelsius and Fahrenheit conversion button;
· ON/OFF button:Power on and off button; Press the button for 3 seconds, it starts;
press it 3 seconds again, it stops.
19
Page 20
Note: This series of wine coolers has its delay protection function. The compressor
Shelf Change LW28D, LW46D,LW72D,LW142D,LW165D, LW306D,
will start to work about 3 to 5 minutes after it is power connected or powered off.
Please use the wine cooler under the T type of climate. The temperature inside the
cabinet will fluctuate and influence the refrigerating effect if the surrounding
temperature is too high or too cold.
LW133DD,LW162DD,LW33S,LW52S,LW155S,LW177S,LW321S,
LW144T
Do as the following shows if needing to pull out or change the shelves;
Firstly take out all the wines from the shelves and pull shelf out to the limit. Then
press down the left limit of sliding rail and meanwhile press up the right one, pull the
shelves out at this time. It could be easily pulled out if doing the three steps (Press
down left limit, press up the right one and puling out) at the same time.
20
Page 21
21
Shelf Change LB80BC, LB148BC, LB36BD, LW3370B
Pull out the wire shelf, make the cove position toward to the pillar at two sides of the
cabinet, then lift up and pull out the wire shelf.
Pull out the glass shelf, make the cove position toward to the pillar at two sides of
the cabinet, then lift up and pull out the glass shelf.
Page 22
Placement and storage of wines Several common layouts of wines:
Your cabinet was designed to store a maximum number of bottles in total security.
The wines are kindly advised to layout equally.
The best temperature for red wines is 52-64℉;For white wines is 43-54℉;
The temperature range of our wine coolers could set between 41-64.
22
Page 23
Reversing the door swing of your appliance (only suitable for model
LW46D,LB148BC,LW72D,LW142D,LW165D,LW52S,LW155S, LW177S,
LW144T)
The unit is delivered to you with the door opening from the left side (hinge on right
side). The door of this appliance is capable of opening from either the left or right
side. To reverse the door swing of your cooler and open from the right side, please
follow the instructions and diagram as follows.
23
Page 24
NOTE: All parts removed must be saved to allow the door swing to be reversed
1.Use the sharp tools to pry open the decoration nail on the top of the cabinet and
the cap of door spindle carefully. (Fig 1)
2. Open the door to an angle, unscrew the screw of the door hinges cover, remove
the cover of the upper door hinge; then unscrew all the screws on the upper door
hinge. Be careful to hold the glass door firmly after removing the screw and take off
the door. (Fig 2)
24
Page 25
3.Remove the screw of lower door hinge and the left side screw of the front vent (Fig
5. Care and Maintenance
Wash the inside surfaces with warm water and baking soda solution. The
Wash the shelves with a mild detergent solution.
Turn off the power, unplug the appliance, and remove all items including
Wring excess water out of the sponge or cloth when cleaning area of the
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well
3); and then install the lower door hinge at the designated position on the opposite
side.(Fig 4)
4.Remove the screw of door handle, then remove the bottom screw of left side of the
door and remove the lower supporter of the door(Fig 5); Install the lower support of
the door to the opposite side.(Fig 6)
5.Pull open middle section of the door gasket, then it will come out the handle screw
hole(Fig 7); remove the handle and install it on the opposite side.(Fig 8)
6.Install the upper door hinge to the opposite side and tighten the screws. (Fig 9)
7.Set glass door shaft to aim the shaft of lower door hinge (Fig 10);and then aim the
upper door hinge (Fig 11); adjust the door and the cabinet is aligned and leveled,
then tighten all the lock screws.
You also can call customer service for reversal instructions if it is necessary.

Cleaning Your Wine Cooler

solution should be about 2 tablespoons of baking soda with a quart of water.
shelves and rack.
controls, or any electrical parts.
and wipe dry with a clean soft cloth.
25
Page 26
Power Failure
Most power failures are corrected within a few hours and will not affect the
temperature of your appliance if you minimize the number of times the door is
Vacancy time
Short vacancy: Leave the Wine Cooler stopping working for around three
Long vacancy: If the appliance will not be used for several months, remove all
Moving Your Wine Cooler
Remove all items.
Securely tape down all loose items (shelves) inside your appliance.
Turn the adjustable leg up to the base to avoid damage.
Make the door shut.
Be sure the appliance stays secure in the upright position during
The Wine Cooler should be located in the coolest area of the room, away from
opened. If the power is going to be off for a longer period of time, you need to
take the proper steps to protect your contents.
weeks.
items and turn off the appliance. Clean and dry the interior thoroughly so as to
restraint odors and mould. Leave the door open slightly all the time if
necessary.
transportation.
Also protect outside of appliance with a blanket, or similar item.

Energy saving Tips

heat producing appliances, and out of the direct sunlight
26
Page 27
6. Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
Refrigerator does not operate
Not plugged in The appliance is turned OFF at the control panel The circuit breaker has tripped or a fuse has blown out
Press ON/OFF Check and make sure the power plug is well connected Ask an engineer for help
Refrigerator is not cold enough; can not cool down to the preset temp.
Compressor does not start
Ask an engineer for help / check the connection of the compressor
Compressor self-protected and has stopped operating
The ambient temperature is too high ( over 38C degree Celsius) The a ir venting is not smooth, check that the air duct is not blocked Fan operates slowly or is faulty and has stopped operating. The door is not closed completely, or the door opened too long The compressor, or its components are faulty
Fans stop working or operate at low speed
Ask an engineer for help. Power the refrigerator ON and OFF. Check the fan and whether the voltage is normal. If the volt age is normal, then the fan should be damaged
Evaporator ices up
Turn OFF the refrigerator for one hour and open the door. The ice on the evaporator will melt. Check the door seal for any air gaps.
Door is not closed properly
Check the door lock, shelves, or other objects, make sure door is well closed. Check the rubber seal for any air gaps. Check the door hinges, make sure they are not loose
Condenser is dusty
Wash and clean the condenser
Cooling system faulty (Gas leakage or blockage)
Ask an engineer for help
Compressor starts and stops frequently
The door gasket does not seal properly.
Use low heat on a hair dryer to make the door seal take shape.
The sensor connection is wrong.
Read the wiring diagram to make t he correct connection of sensor
The sensor is faulty.
Replace with a new sensor
The door is opened too often.
Reduce the times / frequency of door openings.
The light does not work.
Not plugged in, or the light button is “OFF”. Light itself faulty.
Check and make sure the light button is ON, or ask an engineer for help.
The Refrigerator seems to make too much noise.
The stand feet is not leveling, vibrations lead to noise
Adjust the stand feet and ensure they are level.
Copper pipe h its other objects and makes noise
Gently adjust the position of the pipe.
When the compressor shuts down or starts , it is normal for noise from the vibrations generated by the internal moving parts due to inertia.
Take no action
A liquid plumbing noise may come from the flow of the refrigerators gases, which is normal. As each cycle ends, you may hear gurgling sounds
Take no action The door will not close
properly.
Door is blocked by the door lock, shelves, or other objects.
Remove the barrier
You can solve many common wine cooler problems easily, saving you the cost of a
possible service call. Try the suggestions below to see if you can solve the problem
before calling the service.
27
Page 28
Door sealing rubber is deformed
Repair or replace the rubber seal
Door hinges are not loose.
Adjust and fasten the hinges.
Ice up
Outlet / suction outlet blockage
Remove the barrier
Fans stop working or operate at low speed.
Ask an engineer for help. Power the refrigerator ON and OFF. Check the fan and the voltage. If the voltage is normal, the fan may be damaged.
The door gasket does not seal properly; or door is opened too often
Use low heat on a hair dryer to make the door seal take shape.
Gas leakage or cooling system blockage
Ask an engineer for help
External cabinet seems too hot
Ambient temperature is too high, or direct sunshine
Operating conditions need to be improved
Front grill outlet / suction outlet blockage
Remove the barrier
Fans stop working or low speed operating
Ask engineer for help, power on the refrigerator, check the fan whether the voltage is normal or not. If the voltage is normal, the fan should be damage
Water drop on glass door
Ambient humidity is high
Use a soft cloth to clean the water
Door is opened too often
Reduce the times / frequency of door opening.
The door gasket does not seal properly
Use low heat on a hair dryer to make the door seal take shape.
MODEL NO.
LB80BC
LW28D
LB148BC
LW46D
LB36BD
VOLUME
2.83 CF ( 80 Liter )
2.83 CF ( 80 Liter )
5.79 CF ( 164 Liter )
5.44 CF ( 154 Liter )
4.59 CF (130 Liter)
TYPE OF COOLING
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
CLIMATE TYPE
N
ELECTRICITY PROTECTION
GRADE
IIIII
NOMINAL
VOLTAGE/FREQUE
NCY
110-120V/60HZ
RATED POWER(W)
90W / 1.3A
90W / 1.3A
100W / 1.3A
100W / 1.3A
90W / 1.3A
AMBIENT
TEMPERATURE
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
TEMPERATURE
RANGE
3~18or
37~64
5~12or
41~54
12~18or
54~64
1~18or
34~64
5~12or
41~54
12~18or
54~64
5~18or 41 ~64for the left
zone
4~10or 39
~50for the right
zone
7. Data Parameters
28
Page 29
NET W EIGHT
82 lbs (37 KGS)
86 lbs (39 KGS)
106 l bs (48 KGS)
117 lbs (53 KGS)
123 l bs (56 KGS)
PRODUCT
DIMENSION
14.96”W x 23.62”D x 34.45”H
14.96”W x 23.62”D x 34.45”H
23.43”W x 23.62”D x
34.45”H
23.43”W x 23.62”D x
34.45”H
23.43’’Wx23.62’’Dx3
3.86’’H
MODEL NO.
LW33S
LW52S
LW155S
LW177S
LW321S
VOLUME
2.83 CF ( 80 Liter )
5.44 CF ( 154 Liter )
13.42 CF ( 380 Liter )
15.89 CF ( 450 Liter )
26.84CF (760 Liter)
TYPE OF COOLING
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
CLIMATE TYPE
N
ELECTRICITY PROTECTION
GRADE
IIIII
NOMINAL
VOLTAGE/FREQUE
NCY
110-120V/60HZ
RATED POWER(W)
90W / 1.3A
100W / 1.3A
130W / 1.8A
140W / 1.9A
220W / 2.5A
AMBIENT
TEMPERATURE
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
TEMPERATURE
RANGE
5~18or
41~64
5~18or
41~64
5~18or
41~64
5~18or
41~64
5~18or
41~64
NET W EIGHT
82 lbs (37 KGS)
112lbs (51 KGS)
196 l bs (89 KGS)
216 lbs (98 KGS)
309 lbs (140 KGS)
PRODUCT
DIMENSION
14.96”W x 23.62”D x 34.45”H
23.43”W x 23.62”D x 34.45”H
23.42”W x 26.77”D x
63.98”H
23.42”W x 26.77”D x
71.26”H
32.28”W x29.33”D x
79.21”H
MODEL NO.
LW72D
LW142D
LW165D
LW306D
LW3370B
VOLUME
8.48 CF ( 240 Liter )
13.42 CF ( 380 Liter )
15.89 CF ( 450 Liter )
26.84CF (760 Liter)
5.93 CF (168 Liter)
TYPE OF COOLING
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
compressor with air-circulated fan
cooling
CLIMATE TYPE
N
ELECTRICITY
PROTECTION GRADE
IIIII
NOMINAL
VOLTAGE/FREQUENC
Y
110-120V/60HZ
RATED POWER(W)
110W / 1.4A
130W / 1.8A
140W / 1.9A
220W / 2.5A
90W / 1.3A
AMBIENT
TEMPERATURE
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
32 - 100 °F
29
Page 30
TEMPERATURE
RANGE
5~12or
41~54
12~18or
54~64
5~12or
41~54
12~18or
54~64
5~12or
41~54
12~18or
54~64
5~12or
41~54
12~18or
54~64
5~18or 41 ~64for the left
zone
4~10or 39
~50for the right
zone
NET W EIGHT
143lbs (65 KGS)
201 lbs (91 KGS)
220 lbs (100KGS)
320lbs (145KGS)
137 lbs (62 KGS)
PRODUCT DIMENSION
23.43”W x
23.62”D x
48.23”H
23.42”W x 26.77”D x 63.98”H
23.42”W x 26.77”D x
71.26”H
32.28”W x29.33”D x
79.21”H
29.53”W x23.62”D x
34.45”H MODEL NO.
LW144T
LW133DD
LW162DD
VOLUME
15.89 CF ( 450 Liter )
13.42 CF ( 380 Liter )
15.89 CF ( 450 Liter )
TYPE OF COOLING
compressor with
air-circulated fan cooling
compressor with
air-circulated fan cooling
compressor with air-circulated
fan cooling
CLIMATE TYPE
N
ELECTRICITY PROTECTION
GRADE
III
NOMINAL
VOLTAGE/FREQUENCY
110-120V/60HZ
RATED POWER(W)
140W / 1.9A
130W / 1.8A
140W / 1.9A
AMBIENT TEMPERATURE
32 - 100 °F
32 - 100 °F
32 - 100 °F
TEMPERATURE RANGE
5~22or 41~72for
the upper zone
5~12or 41~54for
the middle zone
12~22or 54~72for
the l ower zone
5~18or 41~64
5~18or 41~64
NET W EIGHT
220 lbs (100KGS)
201 l bs (91 KGS)
220 lbs (100KGS)
PRODUCT DIMENSION
23.42”W x 26.77”D x 71.26”H
23.42”W x 26.77”D x 63.98”H
23.42”W x 26.77”D x 71.26”H
30
Page 31
WARRANTY INFORMATION
Please speak to your retailer before calling Lanbo International Inc. if you did not
purchase your refrigerator directly from LANBO.
Limited warranty – If your refrigerator is not operating properly, LANBO
The limited warranty does not cover: Damage due to such things as accident,
misuse, abuse, mishandling, neglect, unauthorized repair or any other cause
beyond the control of the seller whether similar or dissimilar to the foregoing.
Purchaser understands and acknowledges that the goods sold here are WINE /
BEVERAGE COOLERS. Purchaser assumes all the risk of using these units,
including risk of spoilage, humidity variations, temperature variations, leaks, fires,
water damage, mold, mildew, dryness and similar perils that may occur.
reserves the right to repair or replace the refrigerator. LANBO may request the
consumer to contact a local refrigeration company to service the refrigerator. All
cost for labor and materials are covered for 12 months whole parts and
compressor covered for 36 months warranty. If LANBO deems the unit not
repairable. LANBO will use the value of your original order toward a
replacement. For customer service, please contact Lanbo International Inc.
By email: service@lanboappliances.com
SPECIAL NOTE: Warranty is only honored for the unit which is purchased and used
in United States of America. And, if your product was purchased at any 3rd party
retailer and not directly from LANBO, we do not offer an extended warranty policy.
You must contact the retailer of purchase directly. In the event your retailer does not
over an extended warranty plan, we recommend you contact a third party warranty
provider. However, regardless of point of purchase, all LANBO coolers are backed
by a 12 months manufacturer's warranty from date of sale.
31
Loading...