S
S
S
E
E
E
N
N
N
T
T
T
R
R
R
Y
Y
Y
1
1
1
5
5
5
0
0
0
W
W
W
C
C
C
D
D
D
M
M
M
I
I
I
P
P
P
6
6
6
5
5
5
c
c
c
o
o
o
l
l
l
o
o
o
u
u
u
r
r
r
c
c
c
h
h
h
a
a
a
n
n
n
g
g
g
e
e
e
r
r
r
USER’ S MANUAL release 1.0
This manual must be considered an integral part of the projector
1
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
tech@lamposrl.it
SOLID: Dust-tight
WATER: Protected against water jets
Suitable for direct mounting on normally flammable surfaces
Rated maximum ambient temperature (indoor with ventilation)
Connection must be made to a power supply system fitted with efficient
earthing (EN60598-1 – Class I fixture)
Replace any cracked protective shield, dichroic filter or lens
Ignitor circuit lamp have very high voltage
Index
Dimensions and weight ---------------------------------------------------------------------------------- page 2
Technical data --------------------------------------------------------------------------------------------- page 2
Storage ------------------------------------------------------------------------------------------------------ page 3
Admissible environmental conditions ----------------------------------------------------------------- page 3
Power supply ---------------------------------------------------------------------------------------------- page 3
Remove the lid -------------------------------------------------------------------------------------------- page 4
Example of connection ---------------------------------------------------------------------------------- page 5
DMX signal cable ----------------------------------------------------------------------------------------- page 5
User’s interface ------------------------------------------------------------------------------------------- page 7
DMX specifications of projector ----------------------------------------------------------------------- page 8
DMX starting address ----------------------------------------------------------------------------------- page 8
Stand alone mode (colour sequence) ----------------------------------------------------------------- page 13
Stand alone mode (one fixed colour) ----------------------------------------------------------------- page 14
Lamp replacement --------------------------------------------------------------------------------------- page 16
Spare parts ------------------------------------------------------------------------------------------------ page 17
2
Dimensions & weight
Weight: 9Kg
Installation in compliance with the rule UNI 10819 – lighting pollutions
Technical data
- Aluminium body and reinforced techno polymer cover
- Short-arc CDM-SA/T 150W (base G12) lamp
- Magnetic ballast with power factor correction (1.2A max @ 230VAC with lamp ON)
- Innovative colour changing system R.B.G. (more colours combination)
- DMX controlled or STAND ALONE mode
- IP65 protection rate
- Fitting suitable for mounting on a Ø 60mm steel, or fibreglass reinforced plastic pole
3
Storage
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.
Attention, the projector will be damaged during the unpacking.
Admissible environmental conditions
The projector was engineered and produced to function in outdoor areas with an air temperature ranging between 0° and 35°C
and with a humidity level between 30 and 90%.
When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.
Power supply
Connect the fixture to the mains. See the table and the drawing for the colours of the connection cable.
Do not power the projector with a dimmer circuit
When in doubt, consult a qualified electrician.
The projector can be feed with voltage between 210Vac and 240Vac (on the projector body is specified if 50 or 60 Hz). Overvoltage caned damage the electronic parts of the projector or reduce the lamp life. It is advised to check the electric system
before installation.
When the projector is switched on, the starting current is proxy double from the nominal current. After one minute the lamp
has beam switched and the current absorbed goes down to 1.2A (230V).
The projector is complete grounded, it is necessary to connect the grounding system to the projector.
Protect the electric system with highly sensitive differential circuit breaker, 30mA.
The projector has in its inside a fuse, if a power failure should occur, that breake the power supply, if damage change it with a
fuse of the same size.
Attention, the ignitor circuit inside the projector have a very high voltage, over 4.5KV.
4
Remove the lid
Unscrew the 6 screws and remove the plastic cover.
Unscrew the 3 screws and remove the aluminium cover.
Unscrew the 2 screws and remove the motor module.
Turn upside-down the motor module.
Fuse = F5A
Connect the wires, see the tables and the drawing.
Re- insert the motor module and screw the 2 screws.
Re- insert the aluminium coverage and screw the 3 screws.
Re- insert the plastic cover and screw the 6 screws.
5
Example of connection
Example 1: The DMX signal is generated by a DMX controller, the signal cable goes in and out from each projector up to the
last one.
The projectors will execute the same scenes if the DMX addresses are the same (factory set is 1) or they can be driv en one by
one if the DMX addresses are different from each other. (each projector uses 1 or 3 DMX channels):
Projector 1: DMX address 1 Projector 2: DMX address 4 Projector 3: DMX address 7
Example 2: The DMX signal is generated by a projector on stand alone mode (MASTER).
The projector MASTER will automatically execute scenes and it will drive the projector SLAVE of the same model.
In the two examples the projectors can be fed from different power sources, it is not necessary t o swit c h on t he projectors at the
same time.
If the DMX controller or the MASTER projector is not switched on, the projectors are on black-out (version with
dimmer/black-out) or they will project white light (version without dimmer/black-out).
DMX signal cable
Use only shielded and twisted cables with EIA485 (RS485) standards. The cable must be low capacity and an impedance
between 82 and 120 ohm.
It is preferable not to use audio cables.
We advise you to read the example of the following tables as a reference to use to correct cables.
Cables with 1 pair of wires Cables with 2 pairs of wires
Type Cod. AWG Impedance (ohm) Type Cod. AWG Impedance (ohm)
BELDEN 1162A 20 100 BELDEN 8102 24 100
BELDEN 8227 20 100 BELDEN 8162 24 100
BELDEN 89207 20 100 BELDEN 89696 22 100
ALPHA 9109 20 100 PROPLEX PC224P 22 110
ALPHA 9817 20 100 PROPLEX PC224T 22 110
ALPHA 9818 20 100
The wire size we recommended is 26 AWG or higher.
It is preferable:
- not to insert over 32 projectors each DMX chain
- not to use more than 150m of signal cable (with low quality cable)
- not to use more than 300m of signal cable (with good quality cable)
Loading...