M
M
M
I
I
I
N
N
N
I
I
I
O
O
O
U
U
U
T
T
T
L
L
L
E
E
E
D
D
D
r
r
r
g
g
g
b
b
b
I
I
I
P
P
P
6
6
6
5
5
5
L
L
L
E
E
E
D
D
D
c
c
c
o
o
o
l
l
l
o
o
o
u
u
u
r
r
r
c
c
c
h
h
h
a
a
a
n
n
n
g
g
g
e
e
e
r
r
r
USER’ S MANUAL release 2.0
This manual must be considered an integral part of the projector.
1
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
tech@lamposrl.it
LED RADIATION, DO NOT STARE INTO BEAM, CLASS 2 LED PER IEC 60825-1.
For additional information on these led devices with regard to the IEC 60825-1 standard, contact CREE.
SOLID: Dust-tight
WATER: Protected against water jets
Suitable for direct mounting on normally flammable surfaces
Minimum distance from lighted objects (0.3 meters)
Rated maximum ambient temperature (indoor with ventilation)
Replace any cracked protective shield, dichroic filter or lens
Index
Dimensions and weight ---------------------------------------------------------------------------------- page 2
Technical data --------------------------------------------------------------------------------------------- page 2
Storage ------------------------------------------------------------------------------------------------------ page 2
Admissible environmental conditions ----------------------------------------------------------------- page 2
Installation ------------------------------------------------------------------------------------------------- page 2
Connection -------------------------------------------------------------------------------------------------- page 3
Cable wiring ------------------------------------------------------------------------------------------------ page 3
Optical specifications ------------------------------------------------------------------------------------- page 4
Lenses ------------------------------------------------------------------------------------------------------- page 4
Power supply ---------------------------------------------------------------------------------------------- page 5
Spare parts ------------------------------------------------------------------------------------------------ page 5
2
Dimensions & weight
RJ45 female connector from the base + cable clamp
Weight: 0.8Kg
Technical data
- Aluminium body
- IP65 protection rate
- Adjustable bracket
- Can be installed in any position
ATTENTION!!!
Connect the projector only to dedicated power unit.
Up to 20 meters total connection cable (series connection
with UTP straight patch cables).
The power unit (LED POWER RGB) can drive up to 10 Mini OUT Led RGB.
Storage
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.
Attention, the projector will be damaged during the unpacking.
Admissible environmental conditions
The projector was engineered and produced to function in outdoor areas with an air temperature ranging between 0° and 30°C
and with a humidity level between 30 and 90%.
When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.
If the projector is installed in hot area, led life is decreased.
Installation
The projector is designed to be installed on any materials and in any position.
Use the two hole (6mm diameter) of the base, holes distance 84.5mm.
3
Connection
This series of fixtures based on three led’s board, has now a built-in RJ45 female connector
This solution allows the user to get an easier, faster and safer connection.
Connect the projectors to the power unit with standard CAT.5 UTP STRAIGHT PATCH CABLE
, and special HUB RJ45.
Example with three fixtures
: (3 fixtures, 1 led power, 2 Hub RJ45, 5 UTP straight patch cable)
ATTENTION!!!
Don’t plug in or out the connector from the fixture or from the led power when is connected to the main
power. This non-observance will damage permanently the fixtures and the led power.
Cable wiring
568B SPECIFICATION – CABLE MANUFACTURING INSTRUCTION
PIN ORDER OF THE PLUG
4
Optical specifications
- 3 LEDs RGB high power 1.2W Xlamp by CREE
- Approx. 10 years life (continued use)
- Colour mixing system R.G.B.
- Adjustable intensity of each colour: Red, Green, Blue
Lenses
There are three types of lenses, see the draw to identify the lense and the beam angle.
5
Power supply
Disconnect mains power supply before any operations.
Do not power the projector with a dimmer circuit
When in doubt, consult a qualified electrician.
Connect the projector to the power unit (LED POWER RGB) or to the other projectors, 10 max.
Spare parts
When ordering spare parts for the projector remember to mention the model and serial number which can be found on the plate
at the rear of the projector.
Call your area dealer or feel free to contact the manufacturer for any additional assistance.
The improper use of this projector, cancel the guarantee and our responsibility. All the information have been written and driven with
extreme care; however, we do not engage us any responsibility for contingent errors or omissions. We reserve the right to modify and/ or
improve our product as we retain necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of
this handbook, if not expressly authorized.
Loading...