Here following the graphic of the colour mixing and the 4 steps strobe effect (pag. 7 ex.)
Connection
Disconnect mains before connection and maintenance.
Open the back lid to see the AMP 2 poles dmx connectors and the AMP 6 poles power supply
connectors.
8
L
E
D
C
O
N
T
R
O
L
L
E
L
L
E
E
D
D
C
O
N
T
R
O
C
O
N
T
R
O
L
L
L
L
E
E
R
R
R
D
M
X
d
e
d
i
c
a
t
e
d
L
E
D
c
o
n
t
r
o
l
l
e
r
D
D
M
M
X
X
d
e
d
i
c
a
t
e
d
L
E
D
c
o
n
t
r
d
e
d
i
c
a
t
e
d
L
E
D
c
o
n
o
t
r
o
l
l
e
r
l
l
e
r
USER’ S MANUAL release 1.0
This manual must be considered an integral part of the projector.
BEFORE CONNECTING AND USING THE CONTROLLER, IT IS IMPORTANT TO READ
CAREFULLY ALL THE INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS,
CAN DO THE INSTALLATION AND THE MAINTENANCE OF THIS CONTROLLER.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND
THE VOLTAGE VALUES.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
The improper use of this controller, cancel the guarantee and our responsibility. All the information have
been written and driven with extreme care; however, we do not engage us any responsibility for
contingent errors or omissions. We reserve the right to m odify and/ or improve our product as we retain
necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of
tech@lamposrl.it
this handbook, if not expressly authorized.
Index
Dimension ----------------------------------------------------------------------------- pag. 2
Technical data ------------------------------------------------------------------------ pag. 2
Functions description --------------------------------------------------------------- pag. 3
Manual mode ------------------------------------------------------------------------- pag. 3
Automatic mode ---------------------------------------------------------------------- pag. 4
Programming mode ----------------------------------------------------------------- pag. 5
Connections --------------------------------------------------------------------------- pag. 8
Dimension
Pic. 1 Holes for wall mounting
Technical data
- Plastic case
- Main supply 9Vdc, 300mA (included)
- Controls projector via DMX 512 signal
- Control up to 6 independent group of LED’s colour changer, (48 channels = 6 x 8ch)
- Manual mode or automatic mode
- Possibility to record up to 4 programs with 9 steps for each one
- Green light graphic display 128x64
- Multifunctional 5 digit keyboard
- Holes for wall mounting on the back (Pic. 1)
2
The display in zone 2 will show the labels from L1 to L6, with their values (from 0 to 255).
Each label represent one group of lights:
L1 = group 1 (dmx starting address 1)
L2 = group 2 (dmx starting address 9)
L3 = group 3 (dmx starting address 17)
L4 = group 4 (dmx starting address 25)
L5 = group 5 (dmx starting address 33)
L6 = group 6 (dmx starting address 41)
The display in zone 3 show the dmx values of R (Red), G (Green), B (Blue), A (Amber), and
ST (Strobe) of the group of lights used.
To modify the ongoing step assign a time different from 0 and with button C you can move
from one value to the other of the labels (from L1 to L6).
When you are on a label, use buttons A and B to modify the values and see what the projector
does if it is connect to the led controller or you can check on zone 3 the values.
After these steps, press button D to confirm and change the next label.
To assign the last step of a program, you have to put the seconds of following step to zero.
Example: to have a 3 steps program, you can edit the step 0, step 1 and step 2, then you must
put to zero the seconds of the step 3, after that push E button to save.
The led controller automatically mixes the steps, see the following example.
The led controller automatically mixes the steps of the program. It should not be possible to
assign mixing time and holding time of the colour in one step, but it is possible to assign the
holding time of this colour in two steps: step 1, choose the colour that will be mixed with the
previous colour (example 5 sec.); step 2, the same colour will remain for the set time
(example 10 sec).
7
Loading...