LaMotte WaterLink Spin Touch DW Quick Start Manual

Touch

WaterLink

nSp

DW

TESTING

QUICK START GUIDE

[e-mail] | 410-778-3100 | 800-344-3100 | www.lamotte.com

1. Press and hold until the
meter turns on.

2. Tap

. Select a Water Source

type. Tap

le

to confi rm.

3. Tap

. Select a disk series

(found on disk packaging). Tap

f

o

to confi rm.
NOTE: Disk Series are limited
by Water Source Type
selection.

4. Remove a disk from the
packaging.

5. Use the syringe (1189) to fi ll
the disk with the water sample.

6. Insert the disk. Cover the disk
with the Universal Disk Cover.
Close the lid.

7. Tap

to start test. Tap

to stop the test.

8. The results will be displayed.

9. Choose an option.

- Tap

e

e

to return to the Test

Screen.

- Tap the highlighted

to
save the test results to the
test log if Auto Save is not
enabled.

- Tap the hightlighted
to send the results to the
enabled Mobile Bluetooth
Printer.

10. Press and hold

for 2

seconds to turn the meter off .

DOS & DON’TS

¬ The change Hardness test result units (gpg, ppm) go to

> Other Settings > Hardness Units
¬ Do not touch top or bottom of disk. Handle disk on edge.
¬ Hold syringe vertically when fi lling disks.
¬ Fill the disk on a dark surface to more easily see the sample water.
¬ Do not fi ll disk while in the meter. Fill disk on clean, dry surface.
¬ The disk should not contain any large air bubbles. Air bubbles will

result in erroneous results.
¬ Always use the disk cover.
¬ Only the Universal Disk Cover (Code 1719) can be used with the

WaterLink

®

Spin Touch™.
¬ Empty syringe of previous sample before fi lling with next sample.
¬ Remove fi lled disk from meter after testing. Do not travel with fi lled

disks in meter. They may leak.

BEFORE FIRST USE

¬ Fully charge battery.
¬ Ensure your Spin Touch has the latest fi rmware:

For fi rmware updates contact technical support at 800-344­3100 ext. 3 or

[e-mail].

Disk Patent No. 8,734,734
FCl Patent No. 8,987,000
TCl Patent No. 8,993,337

3585-QG

07.20.17

[e-mail] | 410-778-3100 | 800-344-3100 | www.lamotte.com

FILLING

1. Fill the disk using slow, even
pressure. The sample water will
fi ll the spaces between the baffl es
in a counterclockwise order. Each
space will fi ll from the bottom to
the top. Sample water should be
added until the sample water in the
fourth chamber fi lls to the top of the
chamber slightly past the embossed
fi ll line. It is OK to fi ll slightly past the
fi ll line.

Correct Fill

(Fill line)

2. Do not overfi ll the disk. If the disk is
overfi lled, sample water will fl ow out
of the overfl ow hole in the center of
the disk. The disk is not leaking. Dry
the disk and run the test.

Over
Filled

(Dry disk before placing in meter)

3. Do not under fi ll the disk. If the disk
is under fi lled, the reagent chambers
will not fi ll entirely and results will be
inaccurate.

Under
Filled

4. Wet disks should be dried thoroughly
with a lint free wipe. The disk should
be handled by the edges.

5. Disks should be fi lled and used within 10 minutes. They cannot be
fi lled ahead of time.

For fi lling and troubleshooting tips go to:

www.waterlinkspintouch.com

BLUETOOTH CONNECTION

The WaterLink Touch Spin Touch is capable of connecting to a Bluetooth
enabled device, such as a phone or tablet, and the Mobile Bluetooth
Printer (Code 5-0066). At this time, although the meter can connect
to a phone or tablet, software is not available for transferring data. The
Spin Touch is confi gured to connect to and print, only to the LaMotte
Bluetooth Printer (Code 5-0066). Other Bluetooth printers are not
supported.

Whenever the

button appears on the touch screen the Spin

Touch is capable of connecting to the Mobile Bluetooth Printer (Code
5-0066). The

will be highlighted when connected and dim when not

connected.

The WaterLink Spin Touch will automatically connect to the nearest
Bluetooth enabled printer. It is not necessary to pair the Spin Touch a
Bluetooth enabled device. Barriers to wireless signals can reduce the
range of wireless devices. The WaterLink Spin Touch will work best if
there are no walls between it and the receiving devices.