Laird CMX69273P Assembly And Installation Instructions Manual

Please read all instructions carefully before attempting to
install and use this product.

SAFETY

The CMX69273P and all associated equipment should be installed in
accordance with all applicable local and national electrical code
guidelines to ensure safe operation.

S

PECIFICATIONS – Model Number CMX69273P

Frequency

698 MHz - 960MHz

1710MHz - 2700 MHz

Gain (dBi)

4.1 (typical), 4.5 (max) @ 700 Band

4.2 (typical), 4.2 (max) @ 800 Band

4.1 (typical), 4.2 (max) @ 900 Band

3.3 (typical), 3.5 (max) @ 1800 Band

2.9 (typical), 3.3 (max) @ 1900 Band

2.6 (typical), 2.9 (max) @ 2100 Band

2.8 (typical), 3.3 (max) @ 2300 Band

3.1 (typical), 3.3 (max) @ 2600 Band

Port to Port Isolation

<-16dB @ 698-960MHz
<-16dB @ 1710-2700MHz

PIM, 3rd order, 2X20W < -150dBc

Nominal Impedance 50 Ohms

Polarization Linear, Omnidirectional

VSWR

1.7:1 max across the bands

Power

Input (Max.)

50 Watts (ambient temp of 25°C)

Operating Temperature
Range

-40°C +85°C

Cable Semi flexible 402 cable

Connector Model Specific
Exposed Cable length, Lc

Model Specific

Weight

Approximately 0.60 kg (1.32 lbs.)

Mounting

Ceiling mount (drywall or tile flush mount)

Radome PC/ABS, UL94 V-0 (White)

Dimensions, mm Ø250mm (W) x 49mm (H)

RoHs Compliant

CMX69273P

698‐2700MHz Ceiling Mount Antenna

ASSEMBLY AND INSTALLATION INSTRUCTIONS

165-00152_AC_121514

PRECAUTION

For best PIM results:

1. Make sure the connectors are clean and free from any metal
flakes/dirt & tighten the connectors using torque wrench
according to connector torque specification below.

2. Avoid extreme bending to the cable.

3. During installation of the antenna, both cables should not be
crossing one another.

4. Do not remove the dust cap from connectors when not in use.

A threaded post on the back of the antenna and a supplied
mounting nut are the primary mounting method when access is
available to both sides of the mounting surface, such as a
suspended ceiling tile. Mark the desired mounting location on the

tile and cut a ø40mm (1.57”) hole for threaded post. Feed the

cables through the hole and secure the antenna with the mounting
nut. (See figure 1).

The CMX69273P antenna is designed and optimized for LTE MIMO
system requirements covering a wide range of operating frequency.
The covered frequency range includes the band of 700/ 850/ 900/
1800/ 1900/2100/2300/2600. The antenna offers low cross
correlation between the two radiating elements suitable for MIMO
applications.

APPLICATION

Warranty and Liability

Laird warrants to the original purchaser that antenna products will remain free from
defects in materials and workmanship for a period of five (5) years from the purchase
date. If any such defect is discovered within the warranty period, Laird will at its sole
option, repair or replace the Product free of charge upon its return to the factory. This
warranty applies only if the Product is used in a normal fashion, and is void if the
Product is abused, disassembled, tampered with, used unreasonably, or fails as a
result of normal wear. Furthermore, this warranty applies only to defects, which occur
where the proper Product is selected as recommended by Laird and is used in the
fashion recommended by Laird for the defective Product. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND S LIMITED TO A PERIOD OF
FIVE (5) YEARS FROM THE DATE OF ORIGINAL PURCHASE. LAIRD IS NOT LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. ANY WARRANTY EXTENDED
HEREIN SHALL BE LIMITED TO THE PRICE PAID TO LAIRD FOR THE DEFECTIVE
PRODUCT. WHERE STATE OR LOCAL LAW GOVERNS THE PERIOD OF WARRANTY, SUCH
PERIOD SHALL CONTROL.

Americas: +1.847 839.6907

[e-mail]

Europe: +44.1628.858941

[e-mail]

Asia; +86.21.5855.0827.127

[e-mail]

www.lairdtech.com

For best results, mount the antenna near the center of the coverage
area. A line-of-sight path between the antenna and active floor
locations generally works best. Although microwave signals
penetrate cubical dividers and interior walls with little attenuation,
reinforced block walls, banks of metal cabinets, or steel shelving may
attenuate signals or cause multipath, a condition where reflected
signals interfere with the primary signal path. Avoid mounting next to

a column or vertical support that could create a “shadow zone” of

reduced coverage to one portion of the room.

LOCATION

Mini-Din 4.1-9.5 N-Type

90 inch/LBS (10.16Nm) 25 inch/LBS (2.82Nm)

STANDARD MOUNTING

Figure 1

Patent Pending

ABOVE CEILING MOUNTING

Part Number: HKIT-CMx-003

PE Foam Standoff (Double Sided Adhesive)
Part Number: HKIT-CMx-004

Mounting Bracket Part Number: HKIT-CMx-001

Part Number: HKIT-CMx-002

1. Top Mounting

2. Side Mounting

TWIST & LOCK MOUNTING (drywall/sheetrock)

HARD CEILING MOUNTING ABOVE CEILING MOUNTING

NOTE: The optional mounting kits are NOT INCLUDED
with the antenna; it needs to be purchased separately.

CMX69273P

PLEASE REMOVE TWIST & LOCK
MOUNTING LABLE

*DO NOT REMOVE TWIST & LOCK
MOUNTING LABEL OTHER THAN
DRYWALL/SHEETROCK INSTALLATION
OPTION

MOLDING MOUNTING PLATE

(4X) 8-18 X 3/4“ MOUNTING
SCREWS AND ANCHORS

165-00152_AC_121514

698‐2700MHz Ceiling Mount Antenna

ASSEMBLY AND INSTALLATION INSTRUCTIONS

QR CODES ANGLE MARKING

Δ0 deg marking below the antenna base plate indicates
0 deg angle of azimuth plane radiation pattern.

1, 2, marking below the antenna base plate indicates
the radiator number in the antenna.

There is a unique QR Codes placed on the back of each antenna,
so system managers can simply scan the code with a
smartphone and instantly see all of the needed performance
data. The solution provides fast, accurate data and allows
customers to instantly track even more information than they
could previously review.

TEXT EMBEDDED IN QR BARCODE:

CMX69273P-XXXX-SNYYWWZZZZ,
PORT 1 VSWR: V@700MHz, V@850MHz, V@900MHz,
V@1500MHz, V@1800MHz, V@1900MHz, V@2100MHz,
V@2300MHz, V@2600MHz;
PORT 2 VSWR: V@700MHz, V@850MHz, V@900MHz,
V@1500MHz, V@1800MHz, V@1900MHz, V@2100MHz,
V@2300MHz, V@2600MHz;

LOW PIM PORT 1 HIGH BAND: -LdBc, LOW BAND: -LdBc;
LOW PIM PORT 2 HIGH BAND: -LdBc, LOW BAND: -LdBc;

QR CODE: CMX69273P-XXXX-SNYYWWZZZZ = SERIAL

NUMBERING

V = VALUE OF VSWR @ FREQUECY BANDS (700MHz, 850MHz,
900MHz, 1500MHz, 1800MHz,1900MHz, 2100MHz, 2300MHz &
2600MHz) FOR PORT1, PORT 2.
L = LOW PIM VALUE AT LOW BAND & HIGH BAND FOR PORT 1,
PORT 2.

CMX69273P

165-00152_AC_121514

698‐2700MHz Ceiling Mount Antenna

ASSEMBLY AND INSTALLATION INSTRUCTIONS