Page 1
SPECIFICATIONS
PARAMETER
Laird Model Number
Frequency
VSWR (Max)
Max Gain
PIM Test Frequencies
Polarization
Impedance
PIM, 3rd order, 2X20W
Power 50W @ ambient temp 25o C (77oF)
RF Connector Model specific
Radome Color White
Operating Temperature -30°C +70°C
Storage Temperature
Water/Foreign Body Ingress IP-67
Antenna Weight 0.8kg (1.76 lbs)
Flammability UL94-V0
PERFORMANCE
CMS38606P
380-520 MHz
600-960 MHz
1395-1435 MHz
1690-6000 MHz
3.0:1 (380-520 MHz)
2.0:1 (600-960 MHz)
2.0:1 (1395-1435 MHz)
2.0:1 (1690-6000 MHz)
3.1 dBi @ 380-520 MHz
2.9 dBi @ 600-960 MHz
5.4 dBi @ 1395-1435 MHz
7.0 dBi @ 1690-6000 MHz
UHF Band (380-384MHz)
Low Band Cellular (776-786MHz)
High Band Cellular (1870-1910MHz)
Vertical
50Ω
<-150dBc
-40°C +85°C
CMS38606P
ASSEMBLY INSTALLATION
INSTRUCTIONS
Patent Pending
Please read all instructions carefully before attempting to
install and use this product.
SAFETY
The CMS38606P and all associated equipment should be installed
in accordance with all applicable local and national electrical code
guidelines to ensure safe operation.
LOCATION
For the best results, mount the antenna near the center of the
coverage area. A line-of-sight path between the antenna and active
floor locations generally works best. Although microwave signals
penetrate cubical dividers and interior walls with little attenuation,
reinforced block attenuate signals or cause multipath, a condition
where reflected signals interfere with the primary signal path. Avoid
mounting next to a column or vertical support that could create a
''shadow zone'' of reduced coverage to one portion of the room.
PRECAUTION
For best PIM results:
Figure 1
Americas: +1.847 839.6907
IAS-AmericasEastSales@lairdtech.com
Europe: +44.1628.858941
IAS-EUSales@lairdtech.com
Asia: +86.21.5855.0827.127
IAS-AsiaSales@lairdtech.com
www.lairdtech.com
1.
Make sure the connectors are clean and free from any
metal flakes/dirt & tighten the connectors using torque
wrench according to connector torque specification below.
Avoid extreme bending to the cable. Do not remove
2.
the dust cap from connectors when not in use.
STANDARD MOUNTING
A threaded post on the back of the antenna and a supplied
mounting
available
suspended ceiling tile. Mark the desired mounting location on the
tile and cut a ø40mm (1.57") hole for threaded post. Feed the
cables through the hole and secure the antenna with the mounting
nut. (See figure 1).
nut
to
the
are
both
primary
sides of the mounting surface, such as a
mounting
method
when
is
access
165-00177_AC
Page 2
OPTIONAL MOUNTING
CMS38606P
ASSEMBLY INSTALLATION
INSTRUCTIONS
Note: The optional mounting kits are NOT INCLUDED with the antenna; it needs to be purchased separately
165-00177_AC
Page 3
QR CODES
There is a unique QR Code placed on the back of each
antenna, so system managers can simply scan the code
with a smartphone and instantly see all of the needed
performance data. The solution provides fast, accurate
data and allows customers to instantly track even more
information than they could previously review.
TEXT EMBEDDED IN QR BARCODE:
CMS38606P-XXX-SNYYWWZZZZ
VSWR: V@380-520MHz, V@600-960MHz, V@1395-1435MHz, V@1690-6000MHz
LOW PIM 380-520 MHz: -L dBc, 600-960 MHz: -L dBc, 1690-2700 MHz: -L dBc
CMS38606P
ASSEMBLY INSTALLATION
INSTRUCTIONS
QR CODE:
CMS38606P-XXX-SNYYWWZZZZ = SERIAL NUMBERING
V = VALUE OF VSWR @ FREQUECY BANDS (380-520MHz, 600-960MHz, 1395-1435MHz, 1690-6000MHz).
L = PIM Performance Level
165-00177_AC
Loading...