Labgear LDA204L, LDA206L, LDA208L Installation Instructions Manual
Installation Instructions
Introduction
These fully screened general purpose
4, 6 and 8 way ampliers are ideal for
distributing TV and FM DAB radio signals.
Separate inputs for UHF TV (470-790 MHz)
and for FM DAB (40-270MHz).
The 6 and 8 way versions feature a higher
gain “FULL” (18dB) output. This may be
used in conjuction with additional passive
accessories (taps and splitters)
to allow additional outputs to be fed or
to feed other distribution ampliers.
Please Note: If the full power socket is not
being used it must be terminated with the
75Ω terminator supplied.
In weak UHF signal areas, or where a long
downlead cable is required, it may be desirable to
use a masthead preamplier mounted close to the UHF antenna.
These multi-way ampliers feature a built-in 12V line powering
on the UHF input; ther is no need to use a separate power unit for
the masthead amplier. The built-in line power is rated at 25mA (fully short
curcuit-proof) and is compatible with Labgear masthead preampliers.
The masthead gain should be keep to a minimum and genarally only needs to exceed the
downlead cable loss. A single stage 13dB gain masthead (LMA113F) will be suitable for the
great majority of applications.
All units are suitable for direct amplication of digital terrestrial TV (Freeview™) signals.
When connected directly to a UHF aerial the integrated lter remove any signals from Lte 800
4G mobile phone transmitters picked up by an attached antenna.
Applications
Applications include the following:
• Simple multipoint distribution of radio and TV signals.
• The Full Power output on 6 and 8 way units makes these units ideal for use in larger
homes and ats
Please Note: These units have no IR return path and require a digital bypass to be tted to
enable remote control of Sky™ equipment via the RF2 Output. When using these ampliers
with a Sky Digibox, the amplier must be fed from RF OUT-2 socket of the Digibox.
To view satellite RF2 output T Vs require an analogue tuner.
LDA204L, LDA206L & LDA208L -
4, 6 & 8 Way Distribution Amplifiers
For further information or any queries please contact
Customer Careline: 08457 573 479
(Local rate – UK only)
Technical Support: www.philex.com/support
2 –Year Guarantee
Your amplier is guaranteed against faulty components or poor workmanship for a
period of two years from the date of purchase.
This guarantee does not cover accidental or malicious damage (Including damage from
natural causes such as lightening) and will be invalidated by installation or use other
than in accordance with these instructions, repair or attempted repair other than by the
manufacturer, or open or removal of the case. This does aect your statutory rights.
Labgear Reserve the right to modify their designs or specications, In the light of future
developments, without prior notice. Performance gures quoted are typical and subject
to normal manufacturing and service tolerances
General Safety Precautions
To Prevent Overheating
The recommended clearances and other precautions given in these instructions must be
observed to prevent overheating. In addition, units should not be positioned where they
are likely to become covered by curtains/fabrics or thermal insulation materials in a roof
space or similar building void. The unit should not be left resting on a carpet.
Other Precautions
These appliances are not waterproof. They are for indoor use only and must not be positioned where they could be exposed to dripping or splashing water. Objects containing
liquids should not be placed on or near the appliance. To prevent risk of re, keep the
unit and attached wiring well away from naked ames.
Fitted Mains Plug
These appliances are supplied with a standard xed plug already tted. If this is not
suitable, refer to the instructions below. If you need to change the fuse in this plug,
a 3Amp fuse to BS1362 carrying the ASTA or BSI approved mark must be used.
Always re-t the plastic fuse carrier when replacing the fuse.
Changing the Plug
If the tted mains plug is not suitable for the socket outlet in use, it should be cut o
and an appropriate new plug tted. Any instruction supplied with the plug should be
followed. The Brown wire must be connected to the live (L) terminal of the plug and the
Blue wire to the neutral (N) terminal. Neither wire should be connected to the earth (E)
terminal of a 3-pin plug (this appliance does not require an earth connection). Ensure
that the cord grip in the plug is correctly used and clamps the sheath of the cord rmly.
Fuse Rating: If the new plug is a fused type, the fuse tted should be rated at no more
than 3 Amp. Caution: The old plug should be disposed of promptly since it would be
dangerous if plugged into a live socket.
4
1
Installation Instructions
Lte
800
READY
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority for
recycling advice.
© Philex Electronic Ltd. 2014 V1_1
Remote Rooms
Or
FM Aerial
VCR/DVR
TV
TV
FM/DAB
PSW122
Suitable for combined
TV and Radio outlet
PSW111
Suitable for TV outlet
TV
TUNER
TV
2
FULL
1 2 3 4 5 6 7 8
LDA208L
Lte
800
READY
UHF
VHF
AUTO 12V
Full Power to a
passive splitter
ANT IN
Freeview™ Receiver/
PVR/DVD Recorder
UHF Aerial
DAB Aerial
TV with built in
Freeview™ Receiver
Splitter e.g. FBS138
Installation
Important note: attention is drawn to the General Safety Precautions Panel on page 4 which
contains advice on safe installation and operation of these products.
Location
Choose a location for the amplier from which it is convenient to run cables from the
antennas and to the system outlets. Typical examples of suitable locations are a loft space or a
cupboard. In weak signal areas it is best to keep the antenna cables as short as possible.
Select a cool, dry location to install the amplier. This means a location where the ambient
temperature will remain between -10°C and +40°C, and which is free from risk of dripping or
splashing water.
The xing location should allow adequate access to the equipment for wiring and maintenance.
Clearance of at least 25mm should be allowed around the left hand side and top of the unit for
ventilation. More clearance will be needed on the other sides to allow access for cables.
Fixing
The amplier should be xed to a wall or other suitable hard surface, using suitable screws and
masonry plugs (not supplied). The amplier should not be left supported by its own wiring, nor
should it be left resting on a carpet or other insulating and/or inammable surfaces.
Electricity Supply
Fixed wiring and connection of the electrical supply to these products should be carried out in
accordance with BS7671 (IEE Wiring Regulations) .
Each amplier is supplied with a tted 13A mains plug. If this is not suitable, see General Safety
Precautions Panel on page 4.
As an alternative to the use of plug and socket connection, the amplier may be connected to
the supply using a switched fused connection unit BS 1363-4.
A 3 Amp fuse to BS1362 should be tted in the fused connection unit.
If the power unit is connected to the supply other than by means of its tted fused plug or a
fused connection unit, It must be protected by a non-time delayed fuse or a type B MCB at the
distribution board of rating not exceeding 6 Amp. An isolating switch should be provided near
to the unit to allow it to be disconnected from the supply when necessary.
Signal Connections
Input and output signal connections are made using F type (IEC 60169-24) connectors.
Good quality plugs should be used, preferably of the crimp on type. If twist on connectors are
used make sure they are the right size to t the cable you are using. For outside connections
use waterproof connectors.
3
2
LDA204L LDA206L LDA208L
No of Inputs 2
No of Outputs
4 6+1 8+1
Frequency Range UHF 470-790MHz
Frequency Range FM/DAB 47-300MHz
UHF/FM/DAB Gain per port 8dB
Gain to full output
- 16dB 16dB
Max Out put level (IMA3-60dB). EN50083-5
102dBµV 98dBµV 96dBµV
Noise Figure 3.5dB
Return Loss Input/Output 10dB/10dB
Isolation between outlets 20dB
Line Power 12V / 50mA
Built-in Power Supply 220-240V~50Hz at <3W
Dimensions 184 x 85 x 35mm
265 x 95 x 35mm 265 x 95 x 35mm
Installation Instructions Installation Instructions
Loading...