Labgear LABHG32T User Manual

Professional High Gain 32 Element Aerial

LABHG32T

Congratulations on the purchase of your LABHG32T aerial. The aerial is ideal for the reception of all available
signals in strong and medium strength areas. The aerial design has been tuned to minimise reception of signals
above 790MHz from Lte800 4G mobile phone transmitters which can interfere with digital TV channels.

Features include:

• 13.9dBi Gain

• F type connector for secure and easy connection

• Fast simple assembly

• Encapsulated weather resistant electronic balun

Installation Instructions

USER GUIDE

Lte

800

READY

For optimum results install the aerial using double screened CAI benchmarked digital coax cable and s
creened coax outlets. You will need to t the coax cable with the F type connector supplied to connect
to the downlead (not supplied) to the F socket on the aerial.

1. Prepare the Coax Cable: Firstly fit the rubber weather boot provided, to the aerial end
of the cable. Strip the end of the cable as shown in Fig. 1. Once you have stripped the
cable, twist the braid and pull it back on itself, make sure that no braid is touching the
copper core, this will cause a short on the cable and you will not get any signal.

2. Fitting the F connector: Now, simply twist on the ‘F’ connector supplied and trim the
central conductor.

For best results the aerial should be mounted on an outdoor aerial mast and pointed in the
direction of the nearest transmitter* making sure it is in a position where the transmitter
signal will not be obstructed by nearby trees and buildings. If you are in any doubt about
the direction in which the aerial should be pointing or the orientation of the aerial
(horizontal for main transmitter, vertical for relay transmitter) check your neighbours’ aerials.

The aerial requires some assembly. If mounting on an existing mast check that the mast is in
good condition and rmly xed.

Aerial assembly

3. Clip the balun/dipole assembly to the main boom
using the sprung studs to hold it in position as
shown in Fig. 3.

4. Using the reflector clamps, bolt and wing nut, fix
the reflector assemblies to the main aerial boom
as shown in Fig. 4 and Fig. 5.

Fig. 1

Fig. 2

screw connector
body onto cable

cut or tear
away foil

fold braid back
over sheath

Fig. 3

sprung studs

8mm

inner
wire

6.5mm

end of insulation
should be flush
with this face

2mm approx.

main boom

5. Check that the reflector clamp tabs locate in the
holes of the reflector boom sections and that the
wing nut is tight - see Fig. 5.

6. Ensure that the reflector elements are facing the
right way with the rivets facing the back of the aerial.

Fig. 4

reflector
assembly

engage
tab in hole

balun/dipole
assembly

Fig. 5

reflector
clamps

10.

Connect the aerial downlead to the ‘F’ socket on the
underside of the balun (be careful not to over tighten
the

F connector) see Fig. 6.

Fig. 6

11. Slide the weather boot over the ‘F’ connector
and socket to make a good seal - see Fig. 6.

12. Make sure that the downlead is routed as shown in Fig.6.
Use insulating tape, to secure the the coax downlead to
the mast.

13.

Finally connect the aerial to your TV/set top box
and check the picture. Fine adjust the direction
of the aerial to obtain the optimum signal reception.

Troubleshooting

No picture:
Check all connections from aerial to TV.

Poor picture:
Check all connections from aerial to TV.
Check aerial is properly aligned to the correct transmitter.
If the aerial has been loft mounted try mounting outside.

Make sure new digital coax cable has been used
throughout the installation.

Check the transmitter signal is not obstructed by nearby trees or build­ings.

F Connector

Weather

Boot

Insulating
Tape

If in a very weak signal area or for long cable runs,
installing a masthead amplifier will improve the signal.

If in a strong signal area the signal strength may need to be reduced by
fitting an attenuator.

Caution

When mounting the assembled aerial, always observe safety
precautions and use the correct equipment.
Unless you are competent in the use of ladders and other
access equipment, do not work outdoors at roof height.
If in any doubt, refer to a qualied aerial installer.

Specifications

Frequency Range MHz 470-790
TV Channels 21-60
Forward Gain dBd 11.7
Forward Gain dBi 13.9
Front/Back Ratio dB >15.0
Beam Width +/-deg. +/-16°
PCB Balun Yes
Connector F-Type
Length 776mm
Width 535mm
Height 595mm

Useful Websites for Digital Advice:

*To nd out which DTT channels should be available locally
and to nd out where your nearest transmitter is visit:

http://www.digitaluk.co.uk/coveragechecker/

and enter postcode, house number if you also check the
detailed view box you will see a list of transmitter’s with
distances and compass bearings.

For further information, please contact:

Customer careline: 08457 573479 (
Technical Support: www.philex.com/support/

Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority for recycling advice.

Local Rate - UK Only )

© Philex Electronic Ltd. 2014. v1.1