Labgear HDM 8SP4K User Manual

HDM 8SP4K
User Guide
Supports: Full 3D Remote control via IR back channel Ultra HD 4K x 2K resolutions
ULTRAHD
®
Introduction:
Your Labgear 8 way splitter splits the signal from a single HDMI source input to eight HDMI display outputs simultaneously. The splitter supports full Ultra HD 4k x 2k (3840 x 2160) and dual stream 3D. The HD input device can either be controlled at source or remotely from any of the display locations using an IR receiver* with HDMI break in adaptor and an IR emitter. The splitter is housed in a high quality metal housing.
Pack Contents
• 1x 8 way HDMI splitter
• 1x 5V DC power supply
• User manual
Features
• HDMI, HDCP 1.2 and DVI compliant
• Supports full 3D pass-through
• Supports 4k x 2k high resolution
• Bi-directional IR control system
• Support for CEC bypass
• External and internal EDID settings
*Please Note IR receiver, HDMI break in adaptor and IR emitter are sold separately in a kit part no. HDM IRK
Front Panel
HDM 8SP4K
ULTRAHD
HDMI Output LEDs
EDID selection button
Power LED
IR Output
EDID Switch
Power Switch
Rear Panel
L7L6L5 L4
L8
L3 L2 L1
SIG
EDID
Selection
EDID
IR
ON/OFF
➂➃ ➄
O N
OFF
Power Supply
IR Connections
OUT CEC
IR
IR
IN
Display 3Display 1
Display 4 Display 8
OUT CEC
IR
IR
IN
DC 5V
Output1 Output2
DC 5V
1x8 HDMI Splitter
Display 6Display 2
OUT CEC
IR
IR
IN
HDMI IN
HDMI OUT
Output6 Output7 Output8
Input
Output5
Output3 Output4
O N
SIG
EDID
EDID
L7L6L5 L4
IR
L3 L2 L1
L8
OFF
Selection
ON/OFF
0808
IR
HD Source
e.g. Blu-ray Player
5 6 7
OUT CEC
IR
IR
IN
Display 7Display 5
OUT CEC
IR
IN
PLAY
Operation:
1. Use a 4k compatible HDMI lead (not more than 7m long) to connect the HD signal source (e.g. Blu-ray player, PS3, HD satellite box) to the HDMI input socket on the splitter.
2. Use four 4k compatible HDMI leads (not more than 7m long) to connect the four HD display devices (e.g. HD LCD, HD Plasma, HD LED) to the HDMI output sockets on the splitter).
3. Connect the power adaptor supplied to the socket on the splitter and plug it into a 3 pin mains socket.
4. To select one of the display’s resolutions as standard press the EDID selection button switch seven displays will automatically show the same resolution. If however you want each display to show the resolution it is set to, slide the EDID switch
Please Note: Longer HDMI input and output leads can be used for 1080p signals - up to 20m for input and 15m for output.
to the “OFF” position to lock the resolution, the other
repeatedly. Slide the EDID
to the “ON” position.
IR Channel:
To control the HD source from the location of one of the displays:
1. Connect an IR emitter* to the output port on the front panel of the splitter. Place the emitter in direct line-of-sight of the IR sensor on the devce to be controlled.
2. Connect an IR receiver* to an HDMI break in adaptor plug the HDMI cable into the adaptor and plug the adaptor into the HDMI port on the display.
3. You should now be able to operate the HD source device using its remote control. Make sure that the remote being used is in direct line-of-sight of the IR receiver.
*Please Note IR receiver, HDMI break in adaptor and IR emitter are sold separately in a kit part no. HDM IRK
Specications:
Input Port 1x HDMI (Female connector)
Output Port 8x HDMI (Female connector), 1 x IR Channel
Input Lead Max Length for 4k - 7m, for 1080p - 20m
Output Lead Max Length for 4k - 7m, for 1080p - 15m
Bandwidth 10.2Gbps
Output Resolution 3840 x 2160@50/60, 480i~1080P@50/60, 1080P@24/50/60, VGA~UXGA
Operating Temp. -15~55/5°F~131°F
Deep Color 36bit
Housing Metal
Dimensions 276mm(L) x 135mm(W) x 25mm(H)
Weight 1020g
Power Supply Input 100-240V~50/60MHz, 0.3A max.
Power Supply Output DC 5V𝌂2000mA
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE:
1. Do not expose this equipment to rain, moisture, dripping or splashing liquids and make sure that no objects lled with liquids, such as vases, are placed on or near the equipment.
2. Ensure the units are well ventilated. Do not install or place the units in a bookcase, built-in cabinet or other conned space.
3. Do not install near heat sources such as radiators, heaters, or res.
5. Do not place sources of naked ames, such as lighted candles on the unit.
6. Clean this apparatus only with a dry cloth.
7. Unplug the power adaptor from the mains during thunder storms or when the equipment is not in use for a long time.
8. Position the power cord and units carefully to avoid accidents or damage to your equipment.
9. Only use the power adaptor supplied or one with the same rating.
10. Only use accessories specied by the manufacture.
11. Don not open casing there are no user serviceable parts. Refer all servicing to qualied service personnel.
Technical Support
For further information, please contact:
Customer Careline:
Local rate: UK Only
08457 573 479
www.labgear.co.uk
Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority for recycling advice.
© Philex Electronic Ltd. 2014. v1 MK42 0NX
Loading...