V2.2
HD2-SP8
4k 8 Way HDMI Splitter
User Guide
V2.0
Contents
General Safety ..............................................................................................................................2
Introduction ..................................................................................................................................2
Box contents .................................................................................................................................2
Specications ................................................................................................................................3
Operation - Panels and Functions .........................................................................................3
Typical Setup .................................................................................................................................4
Remote IR System........................................................................................................................4
General Safety
• For optimum performance and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Keep this manual for future reference.
• To prevent re or shock hazard, do not expose any part of this device to rain or moisture.
• This product is for indoor use only
• The unit should not be exposed to direct sunlight, very high or low temperature,
moisture, vibrations or dusty environments.
• Do not place the product in enclosed bookcases or racks without proper ventilation.
• Do not use abrasives, benzene, thinner or other solvents to clean the surface of the unit.
To clean, disconnect the unit from the mains, wipe with a clean soft cloth and add a mild
detergent solution if necessary.
• Do not disassemble the splitter or power supply they contain no user serviceable parts.
Refer servicing to qualied personnel only.
• Do not overload wall outlets and extension cords as this can result in the risk of re or
electrical shock.
• SURGE PROTECTION DEVICE RECOMMENDED: This product contains sensitive electrical
components that may be damaged by electrical spikes, surges, lightning strikes, etc.
Introduction
The Labgear range of 4k splitters are designed to split the HDMI signal from a single high
resolution source to mutiple displays without signal loss. They also have a backward IR
function allowing remote control of the source from the display location.*
• Compliant with HDMI2.0, HDCP2.2 and DVI 1.0
• Support video format up to 4k2k@30Hz with 24bit RGB/YcbCR 4:4:4/YCBCR 4:2:2
and up to 4k2k@60Hz with 12bit YCBCR 4:2:0
• Support 3D frame sequential video format up to 1080p@60
• Support high resolution VESA mode video format up to QSXGA@60Hz
• Support LPCM 7.1CH, Dolby True HD and DTS-HD Master Audio
• Support smart EDID control
• Support Remote IR System for controlling a source from any connected display
Box Contents
1x 8 Way HDMI Splitter
1x 5V𝌂2A Power adaptor
1x User guide
2
Specications
14 15 16 17
18 19 20 21
22 23
Video Bandwidth 300MHz/10.2 Gbps
Input Ports 1 × HDMI
Output Ports 8 × HDMI
Output Resolution 480i ~1080p 50/60Hz, 4Kx2K@24/30Hz, YCBCR 4:2:0
ESD Protection
(Human Body model:)
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply 5V/1A DC (US/EU standards, CE/FCC/UL certied)
Dimensions 235mm (W) × 82mm (D) × 17mm (H)
Weight 360g
Chassis Material Metal
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature -20°C ~ 60 °C / -4 °F ~ 140 °F
Relative Humidity 20 ~ 90 % RH (non-condensing)
Power Consumption (Max) 3.5W
Operation - Panels and Functions
HD2-SP8
Power Input Out 1 Out 2
1 2 3 4
Out 3 Out 4 Out 5 Out 6 Out 7 Out 8
5 6 7 8 9 10 11
IR - Tx
Std - Auto
USB
12 13
EDID
Output 5 Output 6Output 3 Output 4Output 1 Output 2
Output 7 Output 8 Input
DC 5V
1. Power: Blue LED indicates power supply connection.
2. Input: Blue LED indicates Source to splitter unit.
3-10. Out 1 - Out 8: Blue LEDs indicate an active TV/display/monitor is connected to the
indicated HDMI Outputs.
11. IR - Tx: 3.5mm IR Emitter socket for IR control.
12. USB: For rmware updates only
13. EDID Std: When in ‘Std’ mode, the EDID will be set to output 1080p@60Hz video and
LPCM 2CH Stereo audio. Use this mode if there are display problems in ‘Auto’ Mode.
EDID Auto: When in ‘Auto’ mode, the unit will read the EDID settings of the display
device connected to HDMI OUT 1. If it detects a 4K2K capable EDID setting it will
transmit the signal in that format to all outputs. If no 4K2K capable EDID is detected
then the unit will output the best resolution that all displays can support.
14-21. HDMI Output 1 - Output 8: Connects HDMI Outputs1 - 8 to HDMI displays for
simultaneous HDMI distribution, or connects an output to another transmitter to
extend the operating distance.
3
14. HDMI Input: Connects the HDMI or DVI output of your source device such as a DVD
player or set-top box via an HDMI cable.
15. DC 5V: Connects the splitter unit to the 5V DC PSU suppplied which is then plugged
into a mains socket.
Typical Setup
Output 5 Output 6Output 3 Output 4Output 1 Output 2
Output 7 Output 8 Input
DC 5V
TV 8TV 7TV 6TV 5TV 4TV 3TV 2TV 1
Blu-ray
Player
Remote IR System
The Remote IR System in conjunction with the HD2 IRK IR Extender Kit (sold separately)
allows you to control your source device from the location of the the display using the
source remote control.
HDMI
HD2 IRK Kit comprises:
1x IR Receiver
1x IR Emitter
1x HDMI Injector
IR Signal
Injector
IR
Receiver
Customer Careline
If you experience any problems setting up your splitter or have any other queries, please call
the Labgear Customer Care Line: 08457 573 479 - (Local Rate UK only).
Alternatively, please visit our website at www.labgear.co.uk
Waste electrical and electronic products should not be disposed
of with household waste. Please recycle where facilities exist.
Check with your Local Authority for recycling advice.
4
IR Emitter
© Labgear 2017. v1 www.labgear.co.uk
Loading...