Lab Companion TH-ICH-300, TH-ICH-800 User guide

OPERATION MAUNAL

TEMPERATURE & HUMIDITY CHAMBER WITH ILUMINATION

TH-ICH-300/800

MANUAL NO.: Manual No. 00HAA0001227 VER.(0.0)

Before using this product, read this entire Operator's Manual carefully. Users should
follow all of the Operational Guidelines contained in this Manual and take all necessary
safety precautions while using this product. Failure to follow these guidelines could result
in potentially irreparable bodily harm and/or property damage.

Thank you for purchasing Jeio Tech’s products.

Jeio Tech Co., Ltd. is committed to customer service both during and after the sale. If you have questions concerning
the operation of your unit or the information in this manual, contact our Sales Department. If your unit fails to operate
properly, or if you have questions concerning spare parts or Service Contracts, contact our Service Department.

ICH Chamber

Identification label

Figure A.

Please locate the identification label on the right side of the instrument. Fill in the information found on the
identification label in the spaces provided above in Figure A. Refer to this identification label information
when calling, if your unit fails to operate properly, or if you have questions concerning spare parts or
service contracts. Additionally, use this information at www.jeiotech.com when you register your
TEMPERATURE & HUMIDITY CHAMBER (TH-ICH MODEL) when you fill out the enclosed registration
card.

Manual No. Manual No. 00HAA0001227 VER.(0.0) iii

Quality Management System

Jeio Tech Co, Ltd. is dedicated to providing world-best product quality
and customer satisfaction. To ensure we maintain this commitment we
have developed and implemented a total quality program, which
conforms to the requirements according to DIN EN ISO 9001:2000 for the
design, development, production, sales and servicing of biotechnology,
environmental chemical engineering related products, and reliable
measuring equipment for electric and electronics (ovens, incubators,
constant temperature humidity chambers, constant temperature baths,
refrigerating bath circulators, heat exchangers and shakers).

Visit our Web site at www.jeiotech.com/eng/images/ISO-Jeiotech-1.jpg to view a copy of our certificate.

Disclaimer

Jeio Tech Co., Ltd. is committed to a continuing program of product development and improvement, and
reserves the right to change information, such as specifications, appearance, and dimensions, described in
this document without notice.

Copyright

No part of this manual may be reproduced or transmitted in any form or by any means, including
photocopying, recording, or using information storage and retrieval systems, for any purpose other than the
purchaser's own use, without the express written permission of Jeio Tech Co., Ltd.

©2009. All Rights Reserved. Jeio Tech Co., Ltd.

Any other product names and services identified in this manual are trademarks or registered trademarks of
their respective owners. No such use, or the use of any trade name, is intended to convey endorsement or
other affiliation with Jeio Tech Co., Ltd.

.

iv ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

Table of Contents

1.0 Safety ------------------------------------------------------- 1

1.1 How to use the Manual-------------------------------------------------------- 2

1.1.1 Introduction----------------------------------------------------------------------------- 2

1.1.2 Chapter summary--------------------------------------------------------------------- 2

1.1.3 Model number nomenclature------------------------------------------------------ 2

1.2 Safety Notice --------------------------------------------------------------------- 3

1.3 Symbols used in this Manual ----------------------------------------------- 4

1.3.1 Signal word panels ------------------------------------------------------------------- 4

1.3.2 Safety symbols ------------------------------------------------------------------------ 5

1.3.3 Miscellaneous none safety symbols used in manual --------------------- 6

1.4 Where to Locate Safety Labels on the Temperature and
Humidity ICH chamber ------------------------------------------------------- 7

1.4.1 TH-ICH-300------------------------------------------------------------------------------ 7

1.4.1 TH-ICH-800------------------------------------------------------------------------------ 8

1.5

Precautions for Your Temperature and Humidity ICH chamber ----------

1.5.1 Warning statements ------------------------------------------------------------------ 9

1.5.2 Caution statements----------------------------------------------------------------- 10

9

1.6 Responsibility -------------------------------------------------------------------11

1.6.1 General responsibility------------------------------------------------------------- 11

1.6.2 Operator responsibility ----------------------------------------------------------- 12

1.6.3 Maintenance responsibility ------------------------------------------------------ 13

1.6.4 Reporting a safety defect--------------------------------------------------------- 13

2.0 Functional Description-------------------------------15

2.1 Introduction for our unit -----------------------------------------------------16

2.2 Features ---------------------------------------------------------------------------18

2.2.1 Control range of Temp. & Humid----------------------------------------------- 18

2.2.2 Elegant design----------------------------------------------------------------------- 18

2.2.3. Uniformed distribution of temp. & humid.(Up-down flow type) ----- 19

2.2.4. Designed for enhanced user’s interface------------------------------------ 19

2.2.5. Safety functions -------------------------------------------------------------------- 19

2.3 Construction -------------------------------------------------------------------20

2.3.1. Unit other components----------------------------------------------------------- 23

2.3.2. Lamp ----------------------------------------------------------------------------------- 24

Manual No. Manual No. 00HAA0001227 VER.(0.0) v

3.0 Installation----------------------------------------------- 26

3.1 Uncrating and inspecting the unit ---------------------------------------27

3.1.1 Inspecting before removing outer container------------------------------------- 27

3.1.2 Removing the unit from shipping container ------------------------------------27

3.1.2.1 Phase 1: Removing the outer container ----------------------------------------------28

3.1.2.2 Phase 2: Removing the unit from skid ------------------------------------------------31

3.2 Unit components---------------------------------------------------------------32

3.3 Preparing the Location ------------------------------------------------------33

3.3.1 Space requirements---------------------------------------------------------------- 33

3.3.2 Environmental setting---------------------------------------------------------------- 35

3.4 Locking/Unlocking Casters & Leveling the unit --------------------36

3.5 Attaching Condensate Drain-----------------------------------------------37

3.6 Pre start-up checks -----------------------------------------------------------37

4.0 OPERATION --------------------------------------------- 38

4.1 Controller -------------------------------------------------------------------------39

4.1.1 Name and function ----------------------------------------------------------------- 39

4.2 Controller operation ----------------------------------------------------------41

4.2.1. FIX RUN --------------------------------------------------------------------------------------------41

4.2.1.1. FIX control --------------------------------------------------------------------------------------42

4.2.1.2. FIX mode ----------------------------------------------------------------------------------------42

4.2.2 PROG Mode--------------------------------------------------------------------------- 43

4.2.2.1. PROG mode ------------------------------------------------------------------------------------43

4.2.2.2 PROG Mode -------------------------------------------------------------------------------------45

4.2.3. Operating and setting of MAIN display --------------------------------------------46

4.2.3.1. COMM SET--------------------------------------------------------------------------------------46

4.2.3.2 RESERVE set -----------------------------------------------------------------------------------47

4.2.3.3 Graph----------------------------------------------------------------------------------------------47

4.2.4. SETUP --------------------------------------------------------------------------------- 48

4.2.4.1. Password----------------------------------------------------------------------------------------48

4.2.4.2. TROUBLE ---------------------------------------------------------------------------------------48

4.3 Lamp Controller ----------------------------------------------------------------49

4.3.1 Name and function ----------------------------------------------------------------- 49

4.3.2 Operation ------------------------------------------------------------------------------- 50

5.0 How to use Software --------------------------------- 51

5.1. Initial display -------------------------------------------------------------------52

5.2. Separate operating display------------------------------------------------53

5.3. Program setting display ----------------------------------------------------55

5.4. Graph display ------------------------------------------------------------------60

vi ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

6.0 Accessories ---------------------------------------------63

6.1 Accessories & Option lists-------------------------------------------------------------- 64

7.0 Appendix -------------------------------------------------65

7.1 Technical Specification------------------------------------------------------------------- 66

7.2 Warranty -------------------------------------------------------------------------------------- 68

7.2.1 Service under Warranty period ------------------------------------------------- 68

7.2.2 Exceptional cases even during under warranty period. ---------------- 68

7.3 Technical assistance---------------------------------------------------------------------- 69

7.3.1 Oversea -------------------------------------------------------------------------------- 69

Manual No. Manual No. 00HAA0001227 VER.(0.0) vii

viii ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.0 Safety

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 1 -

1.1 How to use the Manual

1.1.1 Introduction

This manual is intended for individuals requiring information about the use Temperature and Humidity ICH
chamber. Use this manual as a guide and reference for installing, operating, and maintaining your Jeio
Tech Temperature and Humidity ICH chamber. The purpose is to assist you in applying efficient, proven
techniques that enhance equipment productivity

This manual covers only light corrective maintenance. No installation, service procedure or other
maintenance should be undertaken without first contacting a service technician, nor should be carried out
by someone other than a service technician with specific experience with laboratory equipment and
electricity.

1.1.2 Chapter summary

The Functional Description chapter outlines models covered, standard features, and safety features.
Additional sections within the manual provide instructions for installation, pre-operational procedures,
operation, preventive maintenance, and corrective maintenance.

The Installation chapter includes required data for receiving, unpacking, inspecting, and setup of the unit.
We can also provide the assistance of a factory-trained technician to help train your operator(s) for a
nominal charge. This section includes instructions, checks, and adjustments that should be followed before
commencing with operation of the Temperature and Humidity ICH chamber. These instructions are
intended to supplement standard laboratory procedures performed at daily and weekly intervals.
The Operation chapter includes a description of controller features along with temperature and agitation
parameter setting instructions, multi-segment program setting instructions and instructions for changing the
type of agitation and agitation amplitude.
The Accessories and Option chapter is your source for information on available accessories and option
with brief information.
The Appendix contains technical specifications, warranty and Jeio Tech technical support contact
information.

1.1.3 Model number nomenclature

This manual covers all five models of the Temperature and Humidity ICH series. The following describes
the model number nomenclature used in throughout the manual.

 TH-ICH-300 chamber capacity (300L)
 TH-ICH-800 chamber capacity (760L)

- 2 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.2 Safety Notice

Be sure that you are completely familiar with the safe operation of this Temperature and Humidity ICH
chamber. This unit may be connected to other machinery, such as a temperature control unit. Improper use
can cause serious or fatal injury.

Installation and repair procedures require specialized skills with laboratory equipment and electricity. Any
person that installs or repairs this unit must have these specialized skills to ensure that this unit is safe to
operate. Contact Jeio Tech or their local authorized distributor for repairs or any questions you may have
about the safe installation and operation of this unit.

The precaution statements are general guidelines for the safe use and operation of this instrument. It is not
practical to list all unsafe conditions. Therefore, if you use a procedure that is not recommended in this
manual you must determine if it is safe for the operator and all personnel in the proximity to the
Temperature and Humidity ICH chamber. If there is any question of the safety of a procedure please
contact Jeio Tech before starting or stopping the Temperature and Humidity ICH chamber.

This equipment contains high voltages. Electrical shock can cause serious or fatal injury. Only qualified
personnel should attempt the startup procedure or troubleshoot this unit.

 Documentation must be available to anyone that operates this equipment at all times.

 Keep non-qualified personnel at a safe distance from this unit.

 Only qualified personnel familiar with the safe installation, operation and maintenance of

this unit should attempt start-up or operating procedures.

 Always stop the Temperature and Humidity ICH chamber before making or removing any

connections.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 3 -

1.3 Symbols used in this Manual

The following signal word panels, safety symbols and non safety symbols are used to alert you to
potential personal injury hazards or information of importance. Obey all safety messages that follow
these symbols to avoid possible personal injury or death.

1.3.1 Signal word panels

Signal word panels are a method for calling attention to a safety messages or property damage
messages and designate a degree or level of hazard seriousness. It consists of three elements: a
safety alert symbol, a signal word and a contrasting rectangular background. The following signal word
panels are in accordance with ANSI Z535.4-2007 and ISO 3864 standards.

Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.

Indicates a hazardous situation which, if not avoided, may
result in minor or moderate injury.

Indicates a property damage message.

- 4 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.3.2 Safety symbols

Safety symbols are graphic representations—of a hazard, a hazardous situation, a precaution to avoid
a hazard, a result of not avoiding a hazard, or any combination of these messages—intended to
convey a message without the use of words. The following safety symbols are used in this manual.

Mandatory Prohibition

Read manual

Wear a face mask

Wear gloves

Wear goggles

WARNING

Safety Alert Symbol.
General caution.

No direct sunlight

No high frequency

noise

No corrosive

fluid or cleaners

No water

Hand crush or pinch

Electrical shock

Flammable or fire
could be caused.

Sharp points

Foot crush

Lifting hazard

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 5 -

1.3.3 Miscellaneous none safety symbols used in manual

The following graphic representations are intended to convey a message without words or to bring
your attention to important information about the use of the Temperature and Humidity chamber or a
feature.

European Union
electrical directive
compliance

Earth ground

Relative humidity

Altitude

Note

- 6 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.4 Where to Locate Safety Labels on the Temperature and Humidity
ICH chamber.

The safety labels are attached to the Temperature and Humidity ICH chamber important information
about potential hazards and how to avoid them. All users must read this operating instruction carefully
to operate the product properly.

The following illustrations show where the safety labels should be attached to the Temperature and
Humidity ICH chamber until service of the product is discontinued. If the safety labels are damaged,
please contact your local Jeio Tech office or distributor to request new labels.

1.4.1 TH-ICH-300

Figure 1.2

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 7 -

1.4.1 TH-ICH-800

Figure 1.2

- 8 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.5 Precautions for Your Temperature and Humidity ICH chamber

Our Temperature and Humidity ICH chamber is designed to provide safe and reliable operation when
installed and operated within design specifications. Make sure you read and understand all instructions
and safety precautions listed in this manual before installing or operating your unit. If you have any
questions concerning the operation of your unit or the information in this manual, contact our Sales
Department.

To avoid possible personal injury or equipment damage when installing, operating, or maintaining this
Temperature and Humidity chamber, use good judgment and follow these safe practices:

1.5.1 Warning statements

Observe all warning labels.

DO NOT remove warning labels

Check the voltage, phase and capacity of the power supply and connect properly.

DO NOT ground the Temperature and Humidity chamber to gas pipes or water pipes

DO NOT insert multiple plugs into the outlet at the same time

DO NOT operate equipment with damaged line cords

DO NOT handle or touch electrical cord and electrical parts with wet hands

DO NOT move the Temperature and Humidity chamber while it is plugged into the power source

DO NOT use or keep flammable gases near the Temperature and Humidity chamber.

DO NOT install the Temperature and Humidity chamber near environments where flammable gas may leak.

DO NOT use the machine near environments where explosion can occur due to organic evaporating gases

DO NOT put explosive and flammable chemicals (Alcohol, Benzene, and etc) into the chamber.

DO NOT let moisture, organic solvents, dust, and corrosive gas enter the control panel.

DO NOT expose the Temperature and Humidity chamber to direct sunlight.

DO NOT expose the Temperature and Humidity chamber to direct heat sources.

DO NOT use the Temperature and Humidity chamber in places where moisture is high and flooding can

occur

DO NOT install the Temperature and Humidity chamber near machinery generating high frequency noise.

DO NOT use Temperature and Humidity chamber in environments that contain industrial oil smoke and

metallic dust

DO NOT operate damaged or leaking unit.

DO NOT operate the Temperature and Humidity chamber when there is strange sound, smell and smoke

coming from the unit.

DO NOT disassemble, fix or change the Temperature and Humidity chamber other than for those items

described in this operating manual..

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 9 -

1.5.2 Caution statements

DO NOT use doors, handles or knobs to lift or stabilize the unit

DO NOT place heavy objects on the power cord.

DO NOT put the Temperature and Humidity chamber on the power cord

DO NOT make the machine wet while cleaning

DO NOT pour water or put liquid on the Temperature and Humidity chamber when cleaning the unit.

DO NOT operate Temperature and Humidity chamber and immediately disconnect the main power supply

and request service when water may be in the unit

DO NOT sprinkle insecticide or flammable spray on the Temperature and Humidity chamber

DO NOT clean the Temperature and Humidity chamber with a strong cleanser (e.g., solvent type) and use a

soft cloth.

In addition to the safety warnings listed above, safety messages are posted throughout the manual.
These safety messages are designated by the use of a signal word panel followed by text and a safety
symbol where applicable. Read and follow these important instructions. Failure to observe these
instructions can result in permanent damage to the unit, significant property damage, personal injury or
death.

- 10 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.6 Responsibility

Our Temperature and Humidity chamber are constructed for maximum operator safety when used under
standard operating conditions and when recommended instructions are followed in the maintenance and
operation of the machine.

All personnel engaged in the use of the Temperature and Humidity chamber should become familiar with
its operation as described in this manual.

Proper operation of the unit promotes safety for the operator and all workers in its vicinity.

Each individual must take responsibility for observing the prescribed safety rules as outlined. All caution,
warning and danger labels must be observed and obeyed. All actual or potential danger areas must be
reported to your immediate supervisor.

1.6.1 General responsibility

No matter who you are safety is important. Owners, operators and maintenance personnel must realize

that every day, safety is a vital part of their jobs.
If your main concern is loss of productivity, remember that production is always affected in a negative way
following an accident. The following are some of the ways that accidents can affect your production:

Loss of a skilled operator (temporarily or permanently)

Breakdown of shop morale

Costly damage to equipment and laboratory samples

Downtime

An effective safety program is responsible and economically sound.

Organize a safety committee or group, and hold regular meetings. Promote this group from the
management level. Through this group, the safety program can be continually reviewed, maintained, and
improved. Keep minutes or a record of the meetings.

Hold daily equipment inspections in addition to regular maintenance checks. You will keep your equipment
safe for production and exhibit your commitment to safety.

Please read and use this manual as a guide to equipment safety. This manual contains safety warnings
throughout, specific to each function and point of operation.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 11 -

1.6.2 Operator responsibility

The operator’s responsibility does not end with efficient experimentation and production. The operator
usually has the most daily contact with the equipment and intimately knows its capabilities and limitations.

Plant and personnel safety is sometimes forgotten in the desire to meet incentive rates, or through a casual
attitude toward laboratory equipment formed over a period of months or years. Your employer probably has
established a set of safety rules in your workplace. Those rules, this manual, or any other safety
information will not keep you from being injured while operating your equipment.

Learn and always use safe operation. Cooperate with co-workers to promote safe practices. Immediately
report any potentially dangerous situation to your supervisor or appropriate person.

REMEMBER

 NEVER place your hands or any part of your body in any dangerous location.

 NEVER operate, service, or adjust the equipment without appropriate training and first

reading and understanding this manual.

 Before you start the portable drying/conveying system check the following:

 Remove all tools from the Temperature and Humidity chamber.

 Be sure no objects, samples or chemicals are lying on the Temperature and

Humidity chamber.

 If your Temperature and Humidity chamber has been inoperative or unattended, check all

settings before starting the unit.

 At the beginning of your shift and after breaks, verify that the Temperature and Humidity

chamber is functioning properly.

 Report the following occurrences IMMEDIATELY:

 unsafe operation or condition

 unusual Temperature and Humidity chamber action

 leakage

 improper maintenance

 DO NOT wears loose clothing or jewelry, which can be caught while working on the

equipment. In addition, cover or tie back long hair.

 Clean the equipment and surrounding area DAILY, and inspect the machine for loose,

missing or broken parts.

 Shut off power to the Temperature and Humidity chamber when it is not in use. Turn the

power switch to the OFF position, or unplug it from the power source.

- 12 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1.6.3 Maintenance responsibility

Proper maintenance is essential to safety. If you are a maintenance worker, you must make safety a priority
to effectively repair and maintain equipment.

Before removing, adjusting, or replacing parts on this Temperature and Humidity chamber, remember to
turn off all electric supplies and all accessory equipment at the machine, and disconnect and lockout
electrical power. Attach warning tags where possible.

Be sure that the Temperature and Humidity chamber is correctly connected to earth grounded electrical
outlet that complies with current codes.

When you have completed the repair or maintenance procedure, check your work and remove your tools.

DO NOT restores power to the Temperature and Humidity chamber until all persons are clear of the area.
BEFORE you turn the Temperature and Humidity chamber over to the operator for production, verify the

unit is functioning properly.

1.6.4 Reporting a safety defect

If you believe that your Temperature and Humidity chamber has a defect that could cause injury, you
should immediately discontinue its use and inform Jeio Tech or local authorized distributor.

The principle factors that can result in injury are failure to follow proper operating procedures
(i.e. lockout/tag out), or failure to maintain a clean and safe working environment.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 13 -

- 14 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

2.0 Functional Description

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 15 -

SAME

12 months

6 months

6 months

12 months

6

months

6 months

2.1 Introduction for our unit.

This unit is designed to test for Stability Testing of New Drug Substances and Products Q1A(R2) &

Photostability Testing of New Drug Substances and Products Q1B by the ICH Harmonised Tripartite
Guideline.
The purpose of stability testing is to provide evidence on how the quality of a drug substance or drug
product varies with time under the influence of a variety of environmental factors such as temperature,
humidity, and light, and to establish a re-test period for the drug substance or a shelf life for the drug
product and recommended storage conditions.
The following test conditions are provided in accord with drug substance and drug product by the defined in
this guideline of Q1A.

- 16 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

The Photostability Testing should be carried out systematically including the following tests as below;

 Tests on the drug substance
 Tests on the exposed drug product outside of the immediate pack; and if necessary;
 Tests on the drug product in the immediate pack; and if necessary;
 Tests on the drug product in the marketing pack.

And also the following test conditions are provided in accord with this guideline of Q1B.

 For option 2 the same sample should be exposed to both the cool white fluorescent and near ultraviolet lamp.
 A cool white fluorescent lamp designed to produce an output similar to that specified in ISO 10977(1993).
 A near UV fluorescent lamp having a spectral distribution from 320 nm to 400 nm with a maximum energy emission

between 350 nm and 370 nm; a significant proportion of UV should be in both bands of 320 to 360 nm and 360 to

400 nm.

%

350 370320 400

Wave length(nm)

 The procedure is the same as the following.

samples should be exposed to light providing an overall illumination of not less than 1.2 million lux hours and an

integrated near ultraviolet energy of not less than 200 watt hours/square meter to allow direct comparisons to be

made between the drug substance and drug product.

Fluorescent lamp

• COOL WHITE Lamp

• 1.2 million LUX-hr

• UVA LAMP

UVA lamp

• 320nm~400nm(max. 350~370nm)

• 200W-hr/m2

Fluorescent lamp UVA lamp

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 17 -

2.2 Features

2.2.1 Control range of Temp. & Humid.

FULL RANGE : 20~85%RH
40 ~ 80% RH at 15℃

35 ~ 85% RH at 20℃

30 ~ 85% RH at 30℃

20 ~ 85% RH at 40℃~75℃

20 ~ 85% RH at 85℃

 The spots in circle are indicated by the defined
test temperature/humidity points in accord with
the ICH guideline Q1A(R2).

2.2.2 Elegant design

To differentiate our brand that separates our unit from the established TH chamber, more excellent design is selected
to the unit. Using natural convection heat from lamps be disposed of to the top of the structure was designed. The
lamp is installed inside of the door and you can easily replace them.

- 18 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

2.2.3. Uniformed distribution of temp. & humid.(Up-down flow type)

Adopting 2 Sirocco fan let it maintain
the optimal air flow inside of chamber
with an appropriate air velocity to get
the suitable temp & humid in the
chamber. Opening the door will activate
the automatic stop function of heater
and fan to prevent from contact with an
external air. Air flow is running from
inhaling inner air thru the bottom of the
chamber to the vertical flow passing
thru an evaporator and heater. So
temperature & humidity inside of
chamber will controlled by the way of air
flow.

2.2.4. Designed for enhanced user’s interface

 High quality 304 stainless steel exterior and interior

 Casters for easy transport and installation

 Convenient maintenance - available to check total operating time

 Exclusive door lock & trim

 Vice lock type door catch and foamed silicone packing ensure perfect chamber seal

 Door open warning alarm

 Cable port for running in wires

 Basic hole of 50mm diameter cable port is standard equipped on left side of chambers for wiring to the specimen.

We also provide additional 50 or 80mm diameter cable port (Optional)

 Water tank for easy water supply

- Maintenance can be done easily from the front side

 Door lock device (OPTION)

 Periodical defrosting at below 15 degree make it for long time running with less influence of temp. & humid.

2.2.5. Safety functions

 Leakage breaker for power supply
 Over current protector
 Overheat protector
 Switch-off after alarm for over heating
 Door opening alarm
 Water empty
 The alarm when the photostability test finished.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 19 -

11 12 13 14 15 16 17 18 19 20 21 22

2.3 Construction

5

6

8

7

1

2

3

4

10

9

- 20 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

(1) Controller

- All functions are shown on the LCD Display screen with graphic &

characters.

- Easy operation to push the control buttons.

- All the status of operation is monitored by graphic mode.

- Total Max. 100 programmable segments

Max. 30 patterns supported by each segment.

(2) Lamp control board

-NO/OFF of UV & Fluorescent lamp individually can be controlled.
Pressing the menu button investigate the current strength of the
cumulative value of research strength values
Survey, a screen switch to the desired value is set.
Current time is displayed through the use of 2 lamps, and also
Lamp Replacement time can be found intuitively.

(3) Recorder (Optional)

- 6 points, can display, record and store all temperature & humidity testing

Values and profiles.

- Each channel is sorted out & shown on the display by temp. & Humid.

Recording range: -60 to 150℃/ 0 to 100% RH

Paper wide: 100mm

- Portable type

- 6 dots (Temperature: 5 dots, Humidity: 1 dot)

- Digital display

- Free power supply (100V to 240V)

(4) Handle

- By using plastic mold product, the user can safely close the door,

designed to open the door to open and close even when the power light.
You can bring them to operate a small, sealed with the chamber and more
Designed to strengthen.

(5) Ventilation Hole

- UV Fluorescent and natural convection through the heat generated

at the door to the outside. Perforated to dissipate as the air is
discharged In this and in the perforated and can be used safely and
more prolonged.
The flow of air in the right you can see in the image.

OUTLET

INLET

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 21 -

(6) Cool Air inhalation & Hot Air ventilation Hole

-This perforated air ventilation hole to be drawn
A cool air is provided for cooling down the heat
Generated from the motor & stabilizer, etc
On the upper part, and 2 rectangular fans located
On the rear part of the unit are provided
For better exchange heat capacity and better
Performance of the unit.

(7) Access port

- Basic access port is Ø50mm, and each Ø50mm or Ø80mm Access port
can be added upon user’s request.

-Access port is used for the passing the power cable Thru chamber

for the sample test of electronic components or other Devices

(8), (9) Condensing air ventilation Hole

-Air ventilation holes (perforated plate) are located on the left side & bottom of the rear part of the unit, so hot
air will be drawn off from the refrigerating system thru this ventilation holes. And air pre-filter and air-blowing
perforate plate is installed in front of condensing unit for air ventilation.

(10) Water Tank

-In order to check the water volume directly and prompt response to problems,
Water tank (15L) is located on the front side.
For easy supplying water, Sliding rails are installed.
Auto water filling system is recommendable for the
Comfortable and more than the capacity of a water tank

(15L).

Water purifier is also recommendable when required
The cleanliness control of test sample, or products

(11) Hinge

- Its material is strong enough to stand the heavy weight

load.

- KNUCKLE JOINT made of stainless steel, excellent in strength &

durability.

- Stainless cover boasts of appearance in splendor.

(12) Electric Circuit Breaker

-In order to protect the user, sample & unit, the suitable electric circuit breaker is adopted to meet the unit’s
electrical requirements and automatically cut off the electrical power in case a short circuit, or an electric
leakage.

(13) Communication Port

- RS-232 Communication port is a default setting.

- RS-485 Communication port is an optional which can control

Up to 9 units at the same time. (optional)

(14) Ventilation Hole

-(5) this perforated plate hole is the same function as ventilation Hole.

(15) Door Limit Switch

-If door is open by chance, or accidentally, it gives the signal alarm with stopping the operation of inner blower

for user’s safety by using magnetic door limit switch. It also reduces the radical change of temperature or
humidity inside of chamber.

(16) Tempered glass

-Dual tempered glass to increase insulation and sealing effect and maintenance
of temperature and humidity on the excellent effect.
It have also been due to negligence of use of glass protect users even more
damage can be safe.

- 22 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

(17) Shelf

- 2 shelves are basically provided for the supporting the sample, which made of stainless steel.

- Its appearance has a fine view & clean body due to electro polishing finish.

(18) Fluorescent lamp

Philips is installed by default, and the fluorescent products readily available on the market at a reasonable price, so

easy to obtain and can be replaced by the user.

- TH-ICH-300: 18W, COOLWHITE, 590mm

- TH-ICH-800: 36W, COOLWHITE, 1200mm

(19) UV Lamp
Philips is installed by default, and the fluorescent products readily available on the market at a reasonable price, so

easy to obtain and can be replaced by the user.

- TH-ICH-300: 20W, black light, 590mm

- TH-ICH-800: 40W, black light, 1200mm

(20) Caster
The unit can be placed on a level on the ground

Even if it’s not even ground by adjustment of caster foot.

(21) Water tray

- By any chance of a water leakage, or door chamber
Condensate will build up and drop into this water tray.
Just keep it clean all the time by using a dry cloth.

(22) Water Drain port

-There are 2 drain condensate ports which should be connected to a silicon rubber hose over the drain barb until is
seated against the collar by tying it with a cable tie.

2.3.1. Unit other components

Evaporator

Heater

Door lock

Water Tank

Safety device for test
sample

The established evaporators use the aluminum pins, so it has worry for
corrosion and thermal efficiency decreasing. However, our product is removed
the corrosion problem and progressed the refrigeration efficiency by using the
evaporator that uses the copper pins.
The sheath type heating element for temperature is used in the established
equipment in which takes lots of load to control the operation because it cause
a residual heat when heating and cooling, and lots of a time for the auto
tuning. However, the Nichrome(Ni-Cr) heating element newly adopted has
been improved in the response speed resulting in better performance in
controlling the temperature and reducing the time for auto tuning. And also
the heating element for humidity is made of SUS material not to cause some
problem in quality for the long time running.
Due to the characteristics of the test for long time running, the door lock
should be required to protect the test sample as an optional device.
the water tank(15L) located on the bottom of the front side is installed with
sliding tray for easy supplying water, and also when line water
supply(optional) required, the floating valve in the tank can stop the water
supply when overflowing water as the 2nd safety device.
Test sample can be protected By built-in controller preventing high­temperature, and it’s alarm signal will notify the status of operation to the
operator when the problem occurs.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 23 -

2.3.2. Lamp

Above consists of 6 florescent lamps and 3 UVA lamps.

TH-ICH-300L TH-ICH-800L

- Fluorescent lamp: 18W, cool white, ISO
10977(1993)

- UVA lamp: 20W, black light

Key features

 Optical Detectors (UV sensor / VIS sensor) mounted on the inside, respectively, in the location of each light and

then detected directly and precisely control delivery, Validation City provides a clear data

 Convenient lamp ON / OFF
 Display fluorescent lamp and UV lamp usage time
 You open the door in front of the door safety switch off automatically Lamp promote user safety


Approximately 4,000 hours of lamp life is long-term replacement costs are cheaper

- Fluorescent lamp: 36W, cool white, ISO

10977(1993)

- UVA lamp: 40W, black light

- 24 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 25 -

3.0 Installation

- 26 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

3.1 Uncrating and inspecting the unit

3.1.1 Inspecting before removing outer container

After you have received your Jeio Tech product, inspect the shipping container carefully for any damage that
may have occurred during shipping. Report any damage to the carrier and to your local Jeio Tech office or
the distributor from which the unit was purchased. If the container and packing materials are in re-usable
condition, save them for reshipment if necessary.

3.1.2 Removing the unit from shipping container

The unit is shipped on a wooden skid with an outer and inner container. The wooden outer container is
bolted to the shipping skid and has a protective vinyl cover stapled to the container’s top. Under the outer
container the incubated shaker is covered with a cardboard box and strapped to the skid.

We have segmented the process into 3 phases. Use the following instructions to remove the incubated

shaker from the outer and inner containers

Figure 3.1

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 27 -

3.1.2.1 Phase 1: Removing the outer container

Figure 3.2 Figure 3.3

Step1: Remove the staples holding the vinyl cover to the wooden crate with a straight blade screwdriver.
Step2: Lift the vinyl cover off the wooden crate.
Step3: Inspect the wooden container top for signs of moisture infiltration around the screws.
Step4: Remove the fourteen (14) #7 x 50mm Bugle head screws with a 3Pt Phillips screwdriver. See Figure 3.3..
Step5: Remove the wooden container top.

- 28 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

Figure 3.4

Step6: Remove the seven (7) #14 x 100mm hex head lag screws holding the container front to the shipping skid and
container sides. See Figure 3.4.

Figure 3.5

Step 7: Remove the crate front from the crate supports at points A, B and C using a hammer and/or crowbar. See
Figure 3.5.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 29 -

ate personal injury. To avoid injury

use hammer to bend over or remove, and keep hands and

Figure 3.6

Step 8: Remove the crate supports from the crate back at points D, E, and F using a hammer and/or crowbar. See
Figures 3.5 and 3.6.
.

PANEL IS HEAVY!

minor or moderate personal injury. To avoid injury have
assistance in holding and removing the crate panel.

NAILS/STAPLES ARE SHARP!

crate panel and supports contact with nails/staples could
cause minor or moder

other body parts away from nails/staples.

Dropping crate panel can cause

Be careful when removing

- 30 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

3.1.2.2 Phase 2: Removing the unit from skid

ICH chamber is shipped with the caster feet in the locked position.
Additionally, blocking is used to lock the casters and the unit in place. Use the following procedure to remove
the unit from the skid using a forklift.

Do not use manpower in any cases because it’s heavy for men to lift.

Using forklift
Tool required
None

ICH Chamber

Figure 3.7

Step 1: Carefully slide forklift forks under the incubated shaker. Forks should be set so that outside to outside fork
dimension is 800mm. See Figure 3.7.

Step 2: Slowly lift incubated shaker above the caster blocking and carefully pull the unit out of the crate.

Step 3: Set the incubated shaker on the floor so it rests on the caster feet.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 31 -

3.2 Unit components

After unpacking, please check the contents to ensure you have received all of the following unit
components. Also, check the identification plate on the side of the unit to make sure you received the
model number your ordered.
If you didn’t receive one or more of the components or if the model is incorrect, contact your local Jeio Tech
office, or the distributor from which the unit was purchased.

COMPONENT QUANTITY RECEIVED

Unit

Shelf

Shelf bracket

User instruction

Controller instruction

Drain hose

1

2

4

1

1

2

Access port stopper

Plug & consent

communication software
CD(OPTIONAL)

Cable for communication
(OPTIONAL)

Cable tie

- 32 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

1

1

1

(optional)

1

(optional)

4

3.3 Preparing the Location

3.3.1 Space requirements

ICH chamber is manufactured as the size of Figure 3.10. It is essential the unit to be situated in an area

where there is minimum space 1.2m for the front-ward due to 890mm in width of the door.

Figure 3.10

Model W(mm) D(mm) H(mm) A(mm) B(mm)
TH-ICH-300
TH-ICH-800

1130 985 1520 460 905

1220 1215 1955 545 1185

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 33 -

1. The surface where you place the unit

should be smooth, level and sturdy not to

be shocked or fell down.

2. The unit requires a minimum space more

than 1.5m from the lighting device and

Figure 3.11

more than 20cm from the wall.

3. The floor should be level, and of solid

construction to prevent from any vibration

or a noise.

4. Temperature at the location to be installed

should be below at 30C, 80%RH, and the

place should be located away from the

stove or Heater generating heating source..

5. Be careful when moving the unit due to its

heavy weight.

- 34 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

3.3.2 Environmental setting

The unit can be operated properly under the following environmental conditions for a long time running
without any problem.

No direct sunlight on incubated shaker

Ambient temperature: 18OC to 30OC

Relative humidity not to exceed 85%

Altitude not to exceed 2000m (6,562 feet)

Keep incubated shaker away from high frequency noise produced
by equipment and/or machinery, such as electrical distribution pa
nels, welders, induction heating mechanism, and large amounts of
SCR (Silicon-controlled rectifiers). See Section 6.4—Troubleshooti
ng, Electrical—for the effects of high frequency noise.

Connect the incubated shaker to earth grounded terminals only.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 35 -

3.4 Locking/Unlocking Casters & Leveling the unit

The caster assembly allows for easy movement, locking and leveling of the unit. For proper agitation, it
requires the unit to be level side to side and front to back. Use the following instructions to ensure the unit
is level.

Figure 3.12

Tool required

Step 1: Place the unit in its location.

Step 2: Lower the foot of each caster
by turning the red height adjustment
counterclockwise until it hits the floor.
Turn the height adjustment a quarter turn
or more to ensure the unit’s weight is taken off
the caster. This will lock the unit in place.

Step 3: Place a level on the top of the door

and check for level side-to-side and front-to-back.

Step 4: Turn the height adjustment to raise

or lower the unit until one is level.

- 36 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

3.5 Attaching Condensate Drain

2 Condensate drains are installed on the rear side of the unit. These condensate drains are designed,
one for eliminating any water build up from the inside of chamber heats and cools, the other for escaping
water overflowed from the inside of chamber. To connect the condensate drain to a floor drain or any other
waste the outlet push Ø6mm ID soft-walled tubing, such as: vinyl, FKM, urethane, neoprene or silicone,
over the drain barb until is seated against the collar, then, tie it with a cable tie as shown below

3.6 Pre start-up checks

 Make sure all unit and wall outlet electrical connections are tight.
 Make sure condense drain hose is tightly on hose barb and hose is run to a drain.
 Make sure caster feet are lowered and have locked the unit in place.
 Make sure the unit is level side to side and front to back.
 Make sure there are no flammable or explosive liquids inside of chamber

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 37 -

4.0 OPERATION

- 38 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.1 Controller

1 3 4 6 5

4.1.1 Name and function

1 : LCD display

2

2~6: Keys

Check and monitor unit’s operation.

To start and stop operation.

1. To move from running display to MAIN MENU display.

2. To move a display to another display such as
PARAMETER setting display.(vertical movement)

To move previous or next screen in same category.

1. To choose display movement in MENU display.

2. To enter set value or modify set value.

3. To move digit point during modifying set value.

1. To move left or right in MENU or Parameter setting
display.(horizontal movement)

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 39 -

2. To move digit point during modifying set value.

5-

1. To move down in MENU or Parameter setting display.

2. To decrease value of Arabic numbers or to change text.

1. To move up in MENU or Parameter setting display.

2. To increase value of Arabic numbers or to change text.

- 40 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.2 Controller operation

4.2.1. FIX RUN

4.2.1.1. FIX control
FIX RUN

1. Turn on Main power.

2. How to operate : Press key and move to Temperature and

Humidity input display.

Input Temperature and Humidity

(Use UP, DOWN, and SHIFT KEY to input value.)

1. TEMP ONLY

Set only temperature value without humidity controlling.

2. TEMP & HUMI

Set and control both temperature and humidity.

3. Press key to move to FIX STOP stand-by screen.

How to start FIX RUN

Press key to operate unit.

Fig.1.

.

Fig.2.

☞ Fig.1. shows FIX RUN mode when press and Fig.2. displays when

pressing key.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 41 -

4.2.1.2. FIX mode

Switching display between FIX and PROG

→ FUNCTION → → SUB SET → → SUB SET1 →

(Use UP, DOWN, and SHIFT KEY to choose mode.)

SUB SET1

▶ OPER MODE: Choose either FIX or PROG by using key.

FIX STOP

FIX mode : Control one point of temperature and Humdity.

FIX STOP : It indicates stop of running.

SP : set value of each temperature and humidity.

READY : It indicates stand-by status. Unit can starts or stop running by

pressing RUN/STOP key.

FIX RUNNING(First screen)

FIX RUNNING : Unit is running.

PROCESS TIME : It indicates running time of unit.

T : It indicates number of ON/OFF operation.

IS : It indicates number of Inner Signal operation.

FIX RUNNING(Second screen)

PV : It is the value of sensor which indicates temperature and humidity inside

chamber.

MV : Current output.

RUN PID NUMBER : It indicates number of operating PID. (Temp, Humi AUTO

TUNING displays during AUTO TUNING.

- 42 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.2.2 PROG Mode

4.2.2.1. PROG mode

PROG mode

1. Turn on Main Power.

2. Each SEGMENT and PATTERN should be programmed for PROG RUN.

PROGRAM editing

→ PROGRAM → → EDIT SET →

EDIT SEG

1. Set value of temperature, Humidity, and running time at each SEGMENT.

(Use UP, DOWN, SHIFT KEY to input value.)

1. TEMP ONLY

Set only temperature value without humidity control.

2. TEMP & HUMI

Set and control both temperature and humidity.

3. Press key to escape from PROGRAM screen.

EDIT PT

EDIT SET → Press key to edit PATTERN.

EDIT PATTERN

1. Input last of SEGMENT(END) and first of SEGMENT(TOP) at each

PATTERN(01 ~ 10).

2. Input number of repetition(RPT).

3. Input JUMP PATTERN(JP) : If 3 is input at PT(01), segment connects from

PT(01) to PT(03).

Ex) Unit operates 2 times of repetition of PT(01)

and skip PT(02). Program stops after PT(03)

performs 1 of repetition from 1st segment to 4th

segment.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 43 -

PROG RUNNING

1. Press key and PROG STOP screen shows.

2. Press key to activate number of PT No. Once it is activated, start

segment can be set.

ex) If you set PTNO 2, PATTERN starts from 02.

3. Press key to finish PTNO set.

PROG RUNNING starts

Press key to start operation.

1. TEMP ONLY or TEMP & HUMI can be selected.

- 44 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.2.2.2 PROG Mode

PROG STOP

PROG mode : Control temperature and humidity with program.

PTNO : It indicates PATTERN number which is set.

Press SET KEY to set.

SEGNO : It indicates number of start SEGMENT.

READY : It indicates stand-by status. Unit can starts or stops running by pressing

RUN/STOP key.

PROG RUNNING(First screen)

PROG RUNNING : Unit is running.

PROCESS TIME : It indicates running time of unit.

RPT : It indicates number of repetition of PATTERN.

PROG RUNNING(Second screen)

R.PID : It indicates number of operating PID.

RM.TM : It indicates remaining time of operation.

PROG RUNNING(Third screen)

HOLD ON: It indicates current holding PT and SEG.

HOLD OFF: It indicates RUNNING status.

PROG RUNNING(Forth screen)

HOLD : Current SP(set point) can be HOLD ON or HOLD OFF.

STEP : Stop current segment and move to next segment.

DOWN : It indicates period of decrease of set value.

SOAK : It indicates maintenance of set value.

UP : It indicates period of increase of set value.

PROG STOP

PATTERN : It indicates stop of running.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 45 -

4.2.3. Operating and
setting of MAIN
display

4.2.3.1. COMM SET

COMM SET

→ FUNCTION → → COMM SET →

(Use UP, DOWN, and SHIFT KEY to set.)

ADDRESS set

ADDR : Input ADDRESS(1 ~ 99)

Maximum 9units can be controlled with RS-485 interface by PC.

Set protocol as PCLK1.

AT TUNING

To move AT TUNING screen;

MAIN MENU → FUNCTION → AT TUNING → SET KEY

☞ It can be set and performed only FIX RUN mode.

AT TUNING can be performed only FIX RUN MODE. It performs with set value of

temperature and humidity. PID value is stored automatically in PID GROUP

when finished.

- 46 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.2.3.2 RESERVE set

4.2.3.3 Graph

MAIN MENU(RESERVE)

→ RESERVE →

NOW : Current Year, Month, Day, and Time.

RUN DATE : Delay on Year, Month, Day, and Time.

SET DATE : Current Year, Month, Day, and Time of NOW DATE.

RESERVE : ON – set or OFF – no delay on.

MAIN MENU(GRAPH)

→ GRAPH →

GRAPH VIEW

Temperature and humidity can be expressed as graph of each SEGMENT of

each PATTER.

PTN : Set PATTERN number which you want to see.

SEG : It indicates start number of SEGMENT.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 47 -

4.2.4. SETUP

4.2.4.1. Password

SETUP(PASSWORD)

MENU KEY → SETUP → DI NAME → SET KEY

(Use UP, DOWN, and SHIFT KEY to set.)

PASSWORD

Change password by press SET KEY → UP, DOWN, and SHIFT KEY. Press

SET key to save password.

PROG OPER : ON ⇒ OPER MODE is changeable.

OFF ⇒ OPER MODE is not changeable.

HUMI OPER : ON ⇒ 2-LOOP(Temperature/Humidity)

4.2.4.2. TROUBLE

OFF ⇒ 1-LOOP(Temperature)

☞ RUN 시에는 PROG OPER cannot be changed during Running.

TROUBLE

“WARN” message displays when system is abnormal (DI2 ~ DI4)

If any trouble happens, unit stops.

ERROR 02 : O-T WATER (over heated humidity heater)

ERROR 03 : DOOR OPEN

ERROR 03 : W-T LEVEL (rack of water)

- 48 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

4.3 Lamp Controller

4.3.1 Name and function

1

2

3

8

1 : LCD display
2~8 : keys

7

4

6

Current value, run value, setting mode can be
changed by pressing MENU key.

Either fluorescent lamp or UV lamp can be selected
in setting mode. Value can be adjusted.

Either fluorescent lamp or UV lamp can be selected
in setting mode. Value can be adjusted.

5

Set value is saved by pressing ENTER key.

1. Lock operation keys : Press and hold KEY LOCK
key more than 2 seconds.

2. Unlock operation keys : Press and hold KEY LOCK
key more than 2 seconds.

Fluorescent lamp can be ON/OFF independently.

UV lamp can be ON/OFF independently.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 49 -

4.3.2 Operation

4.3.2.1 Key to turn on or off fluorescent lamp.

4.3.2.2 Key to turn on or off UV lamp.

4.3.2.3 Change of Mode

Mode is changed whenever press MENU key as below.

 Current mode: Current amount of light displays.
 Integration mode: Integrated amount of light displays.
 Setting mode: Wish integrated amount of light can be set.

4.3.2.4 How to set amount of light

1) Press MENU key 2 times to move to SETTING MODE.

2) Select either fluorescent or UV lamp by using up/down keys. Selected lamp changes dark color.

3) Set value by using up/down keys and press ENTER to save value.

4.3.2.5 In case of lamp is not on.

<Both lamps are off> <FL lamp is off> <UV lamp is off>

4.3.2.6 mark indicates lock status(KEY LOCK).

- 50 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

5.0 How to use Software

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 51 -

5.1. Initial display

This is the initial display of TEMI300_Multi Monitoring program operated. It can make TEMI300

monitor maximum 9units, easily up/download the program and control the saved data.

Click left button to transfer the separate operating display.

(figure.1) initial display

- 52 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

5.2. Separate operating display

Consist of a condition information display and controlling buttons.

Controlling button

Display current PV, SP values
Click the left button to transfer the initial display.

Graph display

(figure. 2) Separate operating display

Menu -> graph: Set the displaying for graphs for individual units and save it or not
Menu -> test mode: Set the on/off for the separate units operating.

Select the graphs saving or not and test periods on the below graph setting display.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 53 -

Set the period for the graphs saving

You can save the graphs. After checking the box, set files, set a files
name and a saving route.

(Figure 3) graph setting display

- 54 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

5.3. Program setting display

You can up/download programs.

Click the button; display the pattern
information setting display

Click the button; display the
segment setting display.

Click the button; display the time
signal display.

Click the button; upload the Pattern date
for setting unit.

Click the button; download Pattern date for a
setting unit.

(Figure. 4) Program pattern setting display

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 55 -

You can make out segments for download and confirm the upload date on the below segment setting

display.

You can set TS (time signal) and WAIT on the below TS & WAIT display.

(Figure 5) Segment setting & TS&WAIT setting display

- 56 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

You can set the condition of pattern for download on the below pattern information setting display.

Set the conditions of the repeated pattern operating
for download.

(Figure 6) Pattern information setting display

Set the indicating period for pattern graph.

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 57 -

Set a pattern number and a unit for upload.

(Figure 7) Upload pattern number setting display.

On uploading the setting pattern to a PC, display the condition as below.

(Figure 8) Uploading display

- 58 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

Set a pattern number and a unit for download

(Figure 9) Download pattern number setting display

On downloading set pattern to a PC, display the condition as below.

(Figure 10) Downloading display

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 59 -

5.4. Graph display

You can convert files and analysis saved graphs.

(Figure 11) Graph display

On clicking left button, check the clicked location

data on the Date View.

Menu -> file -> open: open the saved graphic date.
Menu -> file -> print: printing current display
Menu -> view -> date view: display the Date View.
Menu -> view -> list view: display the List View.
Menu -> set -> set graph: setting the graph display condition
Menu -> zoom in/out- -> zoom in: zoom in saved graph
Menu -> zoom in/out - -> zoom out: zoom out saved graph
Menu -> convert -> excel file:converting saved graphic date to excel file.

You can set the display condition of graphs on the below graph setting display.

- 60 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

(Figure 12) Graph setting display

You can confirm current PV, SP, Date & Time on the below Date View display

(Figure 13) Date View display

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 61 -

You can confirm total data of opened files on the below List View display.

(Figure 14) List View display

You can convert opened file data to Excel files on the below Excel files creation display.
The converted Excel files will be saved at the same location as the opened file.

(Figure 15) Excel file creating display

- 62 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

6.0 Accessories

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 63 -

6.1 Accessories & Option lists

Cat. No. Description Remark

AAA8T500 Recorder (6 points)

AAA8T505 Recorder (Digital, 6 channels)
AAA8T541 Interface converter included a cable (5m)

AAA8T542 Interface cable (5m)

AAA80550 Warning signal lamp

RTD1196 Wire shelf for TH-ICH-300
RTD1198 Wire shelf for TH-ICH-800

AAA80604-2 Perforated shelf for TH-ICH-300

AAA80604-4 Perforated shelf for TH-ICH-800

AAA8T610 Cable port (Ø 50mm/ 2.0")
AAA8T611 Cable port (Ø 80mm/ 3.2")

AAA8T621 Water purifier

AAA80622 Water cartridge tank

RTD0794 Humidity sensor
CFA1910 Temperature sensor (RTD type)

RTD1190 Fluorescent lamp(Cool white) for TH-ICH-300

RTD1191 Fluorescent lamp(Cool white) for TH-ICH-800

RTD1188 UVA Lamp for TH-ICH-300
RTD1189 UVA Lamp for TH-ICH-800

AAA80680 THE-680 UV Sensor TH-ICH

AAA80681 THE-681 Illumination Sensor for TH-ICH

AAA80661 Door lock device
AAA80620 Direct water System

- 64 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

7.0 Appendix

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 65 -

7.1 Technical Specification

Model

Chamber volume 300L 760L

Controller PID control(LCD Type)

Without

Range

Temperature1)

Humidity

humidity

With

humidity

Fluctuation2) ± 0.3°C at 40°C / 60%RH ± 0.3°C at 40°C / 60%RH

Variation2) ± 0.5°C at 40°C / 60%RH ± 0.7°C at 40°C / 60%RH

Range

TH-ICH-300 TH-ICH-800

-5 ~ 85°C without Light

+0 ~ 85°C with Light

FULL RANGE : 20~85%RH

40 ~ 80% RH at 15℃
35 ~ 85% RH at 20℃
30 ~ 85% RH at 30℃

20 ~ 85% RH at 40 ~75℃ ℃

20 ~ 85% RH at 85℃

Fluctuation2) ± 3.0%RH at 60%RH / 40°C

Variation2) ± 5.0%RH at 60%RH / 40°C

Light source

(ICH Q1B

option2)

Cool white 3) 6000lux 6500lux

Ultraviolet-A 3) 4.5W/m2 5.0W/m2

Light Uniformity

Typical Time Required to Reach ICH

Recommendation of 200 W-hr/m

2 4)

Typical Time Required to Reach ICH

Recommendation of 1.2 million lux-hr

heating 5) 25min(20 →85 )℃ ℃ 30min(20 →85 )℃ ℃

Time

cooling 5) 35min(20 →℃ -5 )℃ 40min(20 →℃ -5 )℃

System air-cooled

Refrigeration

Refrigerant R-404A

Capacity 250W 470W

Cooler Copper plate fin cooler

Material Ni-Cr Wire Heater / SUS Tube Heater

Heater

Drying bulb 1500W 2300W

VIS.: ±10%

UVA : ±15%

4)

≒ 50Hr 40Hr≒

200Hr≒ 184Hr≒

VIS.: ±15%

UVA : ±15%

Humidity bulb 1200W 2000W

Temperature Pt 100

Sensor

Humidity Electronic sensor(free of drying a wet pack and good response timer)

Air flow 2 set of sirocco fan(2X60W) : Vertical type

Internal SUS #304(2B polish)

External SUS #304(hairline finish) & Steel, 2.0t, Double painted & baked

Material

Insulation Polyurethane(70mm)

Door EPDM Sheet

- 66 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

Operating temperature 18 ~ 30 , 85%RH(non℃ ℃ -corrosive and pure place)

capacity 15L

Water tank

quality

Interface BASICALLY RS-232C, [RS-485:OPTIONAL]

pH6.2 ~ 7.2, Electrical conductivity 20㎲/cm to below

Cable Hole

Dimension Internal 750X650X650 750X880X1160

(W×D×H,mm) External 1130X985X1520 1220X1215X1955

AC220V,1ph,

Max. Power

consumption

Weight(net) 280 ± 10kg 400 ± 10kg

1) All specifications are under ambient temperature 20 (68 ), no load ℃ ℉

2) Technical data (according to DIN 12880, IEC 60068)

3) It was measured in the center of front chamber with lamp vertically.

4) ICH guideline (Q1B option2)

5) Up to 98% of the set value

Control of Temp. Humidity are comply with ICH guideline Q1A (R2)※
The Temperature could go up in the condition with defrost, The humidity could be changed as well.※
Permissible ambient Condition: Temperature 18 to 30 (64.4 to 86 ), Maximum re※ ℃ ℉ lative humidity 85%

→ Recommended ambient temperature: +20 (68 )℃ ℉

60Hz

AC230V,1ph,

50Hz

Optionally max. two holes available/ Ø 50 or 80mm (2.0 or 3.2")

Basically one hole provided/ Ø 50mm (2.0")

15.4A 24.5A

14.7A 23.5A

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 67 -

7.2 Warranty

7.2.1 Service under Warranty period

If trouble occurs during product use, user can get free service for 2 year.
Limited warranty from the date of purchase.
During the warranty period, user can get free service like repairing, replacements, refund.

7.2.2 Exceptional cases even during under warranty period.

User can not be credited by warranty in case of as below.

① If trouble occurs by an act of God.
② If the equipment breaks down due to misusing of available voltage.
③ If damage occurs by dropping a product, or impact.
④ If damage occurs in an appearance by organic solvents such as thinner, benzene.
⑤ If damage occurs without following to notice in the manual.
⑥ If damage occurs by fixing the equipment by any person who is not related with Jeio tech.
⑦ If damage occurs by a mistake of a customer.

- 68 - ⓒ2009. All Rights Reserved. Jeio Tech Co., Ltd

7.3 Technical assistance

7.3.1. Oversea

U.S.A.

Jeio Tech, Inc.
1-A Gill Street
Woburn, MA 01801 USA
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]

China

RM107, No. 68 Line, 569 Xin Hua Road, Shanghai, China
Postcode: 200052
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]

South East Asia

No.7A, Jalan Kemboja 1 B/2, 48300 Bandar Bukit
Beruntung, Selangor Darul Ehsan, Malaysia
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]

England (UK)

Unit 33, Monument Business Park Warpsgrove Lane
Chalgrove, Oxfordshire OX44 7RW, UK
TEL: [phone]
FAX: [phone]
E-mail:

Manual No. Manual No. 00HAA0001227 VER.(0.0) - 69 -