L.A. Baby CW-560 User Manual
Berkshire Crib
Warnings & Instructions
Product # CW 560
Read all instructions before
assembly and use of crib.
Tools needed: Allen wrench
Parts List Pieces per Unit
Rails, Stationary
A - 2
B - End Panel 2
C - Mattress Support 1
D- Mattress, 3” 1
E - Hex Bolts 12
F - Lock Washer 12
G -Barrel Nuts 12
H -Teething Rail (Pre-installed) 2
I - Caster 4
J- Allen Wrench 1
D
H
B
C
B
I
E
G
F
I
L.A. Baby Juvenile Products
16039 Loukelton Street
City of Industry, California 91744
Toll free customer service: 800-584-3094
e-mail: customerservice@lababyco.com
B e f o r e s t a r t i n g
assembly remove the
protective co vering
from both sides of the
two end panels.
H
www.lababyco.com
Step 1
Teething Rail (H)
A
B
F & E
Step 2
E & F
B
!
!
WARNING: FAILURE TO FOLLOW THESE
WARNINGS AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
NEVER use this product if there are any loose or missing fasteners,
!
loose joints, or broken parts. Check before assembly and
periodically during use. Make sure latches are secure.
G
F & E
E & F
WARNING: Infants can suffocate.
G
Contact L.A. Baby for replacement parts.
! NEVER substitute parts
!
! In gaps between a mattress too small or too thick and product
sides.
Note: That one side of each end panel has recessed
drilled holes. These sides are facing outside of crib.
Position side rail (A) with teething rail (G) up and
warnings readable from out side of crib. Attach side rail
(A) to end panel (B) using two hex bolts (E), lock
washers (F) and two barrel nuts (G).Tighten with allen
wrench (J).
Repeat the same procedure as step 1 for attaching
second end panel (B).
! On soft bedding.
NEVER add a mattress, pillow, comforter, or padding.
!
! Use only mattress provided by
WARNING:
manufacturer, which must be at least 38 inches long by 24
inches wide and not more than 3 inches thick.
Step 3
Step 4
A
! This crib including side rails must be fully erected prior to use.
! When child is able to pull to standing position, set mattress/base to
lowest adjustment position and remove bumper pads, large toys,
F & E
and other objects that could serve as steps for climbing out.
! NEVER place a crib near windows where cords from blinds or
drapes may strangle a child.
! Discontinue use of the crib when child is able to climb out or
reaches a height of 35 inches (890 millimeters), the child should be
E & F
E & F
F & E
C
placed in a youth bed.
E & F
F & E
G
Lay crib down on the side rail and place posture board
into position Insert four barrel nuts (G) into the barrel nut
seats located under the posture board. Decide which
height position you want the mattress support (C) to be
(low, middle or high) See “WARNINGS”. Attach mattress
support (C) to the intended position to the end panels (B)
using four hex bolts (E) and lock washers (F). Tighten
with allen wrench (J).
Step 5
D
E & F
F & E
G
Position second side rail (A) with teething rail up and
warnings readable from out side of crib. Attach side rail
(A) to end panels (B) using four hex bolts (E), lock
washers (F) and four barrel nuts (G). Tighten with allen
wrench (I).
Now is a good time to insert the four castors (H) into the
panel posts.
Care Instructions:
! If refinishing, use a non-toxic finish specified for children's
products.
! Child can become entrapped and die when improvised netting or
covers are placed on top of crib. NEVER add such items to confine
child in crib.
! NEVER use a water mattress with this crib.
! Replace teething rail if damaged, cracked, or loose.
! Always provide the supervision necessary for the continued safety
of your child. When used for playing, NEVER leave child
unattended
! To reduce the risk of SIDS, pediatricians recommend healthy
infants be placed on their back to sleep, unless otherwise advised
by your physician.
Acrylic panels requires extra
special care, as they are easily
scratched by common glasscleaning devices or chemically
damaged by glass-cleaning
chemicals. Use only products
J
I
Place the mattress (D) onto the posture board (C )
CAUTION: Use only mattress provided by
manufacturer, which must be at least 38 inches long by
24 inches wide and not more than 3 inches thick.
specially labeled as safe for
acrylic.
Your crib may otherwise be
cleaned, using a damp cloth and
o r d i n ar y m i l d d o m e s ti c
detergent. Do not use abrasives
This crib conforms to applicable regulations promulgated by the
Consumer Product Safety Commission.
! CAUTION: Keep small parts and plastic bags out of reach of small
children
! NEVER use plastic shipping bags or other plastic film as mattress
covers not sold and intended for that purpose. They can cause
suffocation
!
WARNING! Strings can cause strangulation! NEVER
!
place items with a string around a child's neck, such as hood
strings or pacifier cords
! NEVER suspend strings over a crib or attach strings to toys.
DATE OF MFG
Made In China
This crib meets new C.P.S.C. 16 CFR 1220 and
A.S.T.M. 406 Standards. (This crib also meets
A.S.T.M. 2710 Commercial Crib Standards.)
Ins_CW_560_En_050312
Loading...