L.A. Baby CW-530A User Manual

Window Crib

with Folding-Gate Feature

Warnings & Instructions

Product # WC 530 A

Re ad al l in st r u c ti o ns
before assembly and use of
crib.

Tools needed: Allen wrench

Parts List Pieces per Unit

A - Folding-Gate Rail 1

Stationary

B - Rail 1
C - End Panel 2
D - Mattress Support 1
E- Mattress, 3” 1
F - Hex Bolts 12
G -Barrel Nuts 12
H - Lock Washers 12
I -Teething Rail (Pre-installed) 2
J - Caster 4

K- Allen Wrench 1

I

A

B

D

F

G

H

Made In China

Ins_WC_530_En_080511

J

L.A. Baby Juvenile Products

16039 Loukelton Street

City of Industry, California 91744
Toll free customer service: 800-584-3094
e-mail: [e-mail]

www.lababyco.com

DATE OF MFG

B e f o r e s t a r t i n g
assembly remove the
protective covering
from both sides of the
two end panels.

C

E

K

Step 1

C

B

H & F

H & F

G

Note: That one side of each end panel has recessed drilled
holes. These sides are facing outside of crib. Position side
rail (B) with teething rail up and warnings readable from out
side of crib. Attach side rail (B) to end panel (C) using two
hex bolts (F), lock washers (H) and two barrel nuts (G).

Step 3

H & F

F & H

D

F & H

H & F

G

Lay crib down on the side rail and place mattress support
into position Insert four barrel nuts (G) into the barrel
nut seats located under the mattress support. Decide
which height position you want the mattress support (D)
to be (low, middle or high) See “WARNINGS”. Attach
mattress support (D) to the intended position to the end
panels (C) using four hex bolts (F) and lock washers (H).

Step 5

Folding-Gate

Bolt
Knobs

Place the mattress (E) onto the mattress support (D )

CAUT I O N : Use only m a t t r e ss pr o v i d ed by

manufacturer, which must be at least 38 inches long by
24 inches wide and not more than 3 inches thick.

Closing the folding-gate

Pull back both bolt knobs as you swing up the folding­gate and release into the strike plate hole located on the
end panels. Make sure gate is securely locked in
position

Opening the folding gate

Pull back both Bolt knobs and swing the folding-gate
down.

E

Bolt
Knobs

Step 2

C

F & H

F & H

G

Repeat the same procedure as step 1 for attaching
second end panel (C).

Step 4

A

F & H

F & H

G

Position the folding-gate rail (A) with teething rail up and
warnings readable from out side of crib. Attach drop-gate
rail (A) to end panels (C) using four hex bolts (F), lock
washers (H) and four barrel nuts (G).
Now is a good time to insert the four castors (I) into the
panel posts.

I

Care Instruction:

Acrylic glass requires extra special
care, as they are easily scratched by
common glass-cleaning devices or
chemically damaged by glass­cleaning chemicals. Use only
products specially labeled as safe
for acrylic.

Your crib may otherwise be
cleaned, using a damp cloth and
ordinary mild domestic detergent.
Do not use abrasives or bleach. Air
dry.

H & F

H & F

!

!

WARNING: FAILURE TO FOLLOW THESE

WARNINGS AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.

NEVER use this product if there are any loose or missing fasteners,

!

loose joints, or broken parts. Check before assembly and
periodically during use. Make sure latches are secure.

Contact L.A. Baby for replacement parts.

! NEVER substitute parts

!

WARNING: Infants can suffocate.

! In gaps between a mattress too small or too thick and product

sides.

! On soft bedding.

NEVER add a mattress, pillow, comforter, or padding.

!

! Use only mattress provided by

WARNING:

manufacturer, which must be at least 38 inches long by 24
inches wide and not more than 3 inches thick.

! This crib including side rails must be fully erected prior to use.
! When child is able to pull to standing position, set mattress/base to

lowest adjustment position and remove bumper pads, large toys,
and other objects that could serve as steps for climbing out.

! NEVER place a crib near windows where cords from blinds or

drapes may strangle a child.

! Discontinue use of the crib when child is able to climb out or

reaches a height of 35 inches (890 millimeters), the child should be
placed in a youth bed.

! If refinishing, use a non-toxic finish specified for children's

products.

! Child can become entrapped and die when improvised netting or

covers are placed on top of crib. NEVER add such items to confine
child in crib.

! NEVER use a water mattress with this crib.

! Replace teething rail if damaged, cracked, or loose

! Always provide the supervision necessary for the continued safety

of your child. When used for playing, NEVER leave child
unattended

! To reduce the risk of SIDS, pediatricians recommend healthy

infants be placed on their back to sleep, unless otherwise advised
by your physician.

! CAUTION: Keep small parts and plastic bags out of reach of small

children

! NEVER use plastic shipping bags or other plastic film as mattress

covers not sold and intended for that purpose. They can cause
suffocation

!

WARNING! Strings can cause strangulation! NEVER

!

place items with a string around a child's neck, such as hood
strings or pacifier cords

! NEVER suspend strings over a crib or attach strings to toys.

This crib conforms to applicable regulations promulgated by the
Consumer Product Safety Commission.

This crib meets new C.P.S.C. 16 CFR 1220 and
A.S.T.M. 406 Standards. (This crib also meets
A.S.T.M. 2710 Commercial Crib Standards.)