Lab42 MK7 User Manual

WiFi Pineapple Mark VII

Connect to a 2-Amp USB power source.

Join the “Pineapple_XXXX” WiFi Network.

Browse to http://172.16.42.1:1471 and

follow the on-screen instructions.

Your WiFi Pineapple can also be provisioned

with a specially formatted USB flash disk, or by connecting it to a computer using a USB cable.

Learn more at https://docs.hak5.org.

Status LED

Reset Button

USB Host Port

USB-C Power /

Ethernet Port

Access from anywhere online. Free download at https://c2.hak5.org

application of the product(s) described herein. Made in China. Designed by Hak5 LLC, 548 Market Street, #39371, San Francisco, CA, 94104. to the products description in this document without notice. Hak5 LLC does not assume any liability that may occur due to the use or

functionality and other product speciﬁcations are subject to change without notice or obligation. Hak5 LLC reserves the right to make changes device and network dependent and may not be available in all areas; additional terms, conditions and/or charges may apply. All features,

See Hak5.org for additional warranty details and limitations. Availability and performance of certain features, services and applications are WiFi Pineapple is a trademark of Hak5 LLC. This product is packaged with a limited warranty, the acceptance of which is a condition of sale.

circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help.

relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

Information to the User - Part 15.105 (b) Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons.

the equipment. RF Exposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter (Part 15.21) Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

STATEMENT OF CONDITIONS

IN THE BOX

Full documentation at docs.hak5.org

SETUP LED STATUS INDICATIONS

BLINKING BLUE

SOLID BLUE

SOLID RED

ALTERNATING

BLUE/RED

Starting up Ready

Invalid USB Files

Flashing Firmware DO NOT UNPLUG POWER

SAFETY INFORMATION AND WARNINGS

Your device may get hot to the touch; this is normal. Unplug the device and let it cool before removing it. This device complies with applicable

surface temperature standards and limits deﬁned by the International Standard for Safety (IEC 60950-1). Still, sustained contact with warm

surfaces for long periods of time may cause discomfort or injury. Keep the device in a well-ventilated area when in use. Allow for adequate air

circulation under and around the device. Do not expose the device to water or extreme conditions (moisture, heat, cold, dust), as the device may malfunction or cease to work when exposed to such elements. Do not attempt to disassemble or repair the device yourself. Doing so voids the

limited warranty and could harm you or the device. This device is not designed, manufactured or intended for use in hazardous environments requiring fail-safe performance in which the failure of the device could lead directly to death, personal injury, or severe physical or environmental damage.

The WiFi Pineapple is a network administration and pentesting tool for authorized auditing and security analysis purposes only where permitted subject to local and international laws where applicable. Users are solely responsible for compliance with

all laws of their locality. Hak5 LLC and afﬁliates claim no responsibility for

Full documentation at docs.hak5.org

SPECIFICATIONS

INTERFACE: (3) WiFi, (1) USB 2.0, (1) USB-C Ethernet STANDARDS: USB 2.0, 802.11b/g/n DIMENSIONS: 107 x 93 x 21 mm

FREQUENCY RANGE: 2.412 ~ 2.4835 GHz

POWER: 10W (USB 5V 2A)

OPERATING TEMPERATURE: 35ºC ~ 45ºC STORAGE TEMPERATURE: -20ºC ~ 50ºC

RELATIVE HUMIDITY: 0% to 90% (noncondensing)