Küppersbusch IKD3700.0 Instructions For Use And Installation Instructions

IKD3700.0

BEDIENUNGSANWEISUNG

mit Montageanweisungen

GB

Instructions for use and installation instructions
Instructions d'utilisation et avis de montage
Gebruiksaanwijzing en montagehandleiding
Istruzioni di uso e di montaggio
Instrucciones de uso y de montaje
Instruções de uso e de montagem

ПДЗГЙЕУ ГЙБ ФЗН ЕГКБФБУФБУЗ КБЙ ФЗ ЧСЗУЗ

F

NL

I

E
P

GR

in den normalen Hausmüll gehört, sondern den jeweiligen kommunalen Rücknahmesystemen für Elektro- und
Elektronik-Altgeräte übergeben werden muss. Die Entsorgung muss im Einklang mit den geltenden Umweltrichtlinien
für die Abfallentsorgung erfolgen. Für nähere Informationen über Entsorgung und Recycling dieses Produktes
wenden Sie sich bitte an Ihre kommunalen Einrichtungen (Umweltamt) oder an die Abfallentsorgungsgesellschaft
Ihrer Stadt bzw. an Ihren Händler.

ENGLISH

WARNING

The distance between the supporting surface for the cooking vessels on the hob and the lower part of the hood must
be at least 65 cm. If the instructions for installation for the hob specify a greater distance, this has to be taken into
account.
The air collected must not be conveyed into a duct used to blow off smokes from appliances fed with an energy other
than electricity (central heating systems, thermosiphons, water-heaters, etc.).
Comply with the official instructions provided by the competent authorities in merit when installing the disposal duct.
In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for that purpose.
The room must be well aerated in case a hood and some other heat equipment fed with an energy other than electricity
(gas, oil, coal heaters, etc) operate at the same time.
In fact the intake hood, disposing of air, could create a vacuum in the room. The vacuum should not exceed 0,04mbar.
This prevents the gas exhausted by the heat source from being intaken again. It is therefore advisable to ensure
the room contains air taps able to ensure a steady flow of fresh air.

Check the data label inside the appliance; if the symbol ( ) is printed, read the following: this appliance has
such technical particulars that it belongs to class II insulation, therefore it must not be earthed.

The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the
following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows: – the wire which is coloured blue must
be connected to the terminal which is marked with the letter N or coloured black; – the wire which is coloured brown
must be connected to the terminal which is marked with the letter L or coloured red. – terminal of a three-pin plug.

Check the data label inside the appliance; if the symbol ( ) is NOT printed, read the following: ATTENTION:
This appliance must be earthed. When making the electrical connections, check that the current socket has a ground

connection.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the
following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
– the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the
letter E or by the earth symbol [

], or coloured green or green and yellow; – the wire which is coloured blue must
be connected to the terminal which is marked with the letter N or coloured black; – the wire which is coloured brown
must be connected to the terminal which is marked with the letter L or coloured red.
When making the electrical connections, check that the voltage values correspond to those indicated on the data
plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible cable and has
no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact
opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included
in the fixed installation. If your unit features a power lead and plug, position this so the plug is accessible.
Always switch off the electricity supply before carrying out any cleaning or servicing operations on the appliance.

USE

Avoid using materials which could cause spurts of flame (flambées) near the appliance.
When frying, take particular care to prevent oil and grease from catching fire. Already used oil is especially dangerous
in this respect. Do not use uncovered electric grates.
To avoid possible risks of fire always comply with the indicated instructions when cleaning anti-grease filters and
when removing grease deposits from the appliance.

MAINTENANCE

Thorough servicing guarantees correct and long-lasting operation.
Any fat deposits should be removed from the appliance periodically depending on amount of use (at least every 2
months). Avoid using abrasive or corrosive products. To clean painted appliances on the outside, use a cloth dipped
in lukewarm water and neutral detergent. To clean steel, copper or brass appliances on the outside, it is always best
to use specific products, following the instructions on the products themselves. To clean the inside of the appliance,
use a cloth (or brush) dipped in denatured ethyl alcohol.

DESCRIPTION

This appliance is equipped with a completely automatic system (Advanced Sensor Control) capable to

manage all the functions of your hood. Thanks to the ASC, the air in the kitchen is costantly clean and odour
free without any manual intervention. The advanced sensor catches all sort of vapours, smokes and odours
caused by the cooking process. The ASC also captures an abnormal presence of GAS.
Moreover, this hood was born of the Home Comfort project aimed at maximum noise reduction. It also has
an Air Refresh function, which in perfect silence exchanges the air in the room by activating the hood every
50 minutes.

The unit can be found in filtering hoods or ducting hoods. In the Filtering version the air and the kitchen fumes that

are conveyed by the apparatus are depurated by the charcoal filter and put back into the room through the small grilles
of the ventilation flue (Fig. 1). ATTENTION: When using the filtering version, a charcoal filter and an air baffle (Fig. 1A)
must be used, which placed at the top of the structure, allows the air to recycle back into the room. In the Ducting version,
cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2).

INSTALLATION

ATTENTION: 3 persons are required for proper installation; the unit should be installed by a qualified operator.

Also follow carefully each step of the assembly instructions, and once installation has been completed, make sure
that the hood is firmly secured in place.

Before proceeding with assembly operations and to ensure easier manoeuvrability of the appliance, disengage

the grease filter: push the handle outwards and pull the filter downwards. 3).

Also remove the metallic surround by removing the 4 retaining screws (Fig. 4).
Separate the upper part of the telescopic structure from the lower part by removing the 4 retaining screws and

the 4 washers (Fig. 5).

Essential requirements for assembly: – Prepare electricity supply inside the the telescopic flue – If your appliance

is to be installed as a Ducting version, prepare the air evacuation hole.

When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short

as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which
vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section
(diameter: 150 mm).

ASSEMBLY
Ducting version:

Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe
all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must
correspond with the axis of the extractor hood controls.
Secure the upper part of the telescopic structure to the ceiling using the 4 screws and pads supplied (Fig. 6); pay close
attention since the positioning of the structure determines the final position of the extractor hood. During this operation,
pass the air air evacuation pipe inside the telescopic structure and the electricity supply through the specific hole
in the structure (Fig. 6).
Fit the adapter flange on the air output mouth of the motor. 7).
Secure the motor unit to the lower telescopic structure, using 4 nuts and 4 washers (Fig. 8). This block should then
be secured to the upper telescopic structure (Fig. 9) previously secured to the ceiling (with the 4 screws and 4 washers
removed previously). Adjust the height of the telescopic structure using the four screws (Fig. 9) bearing in mind that
the extractor hood must be at minimum distance of 650 mm from the cooking top. (Fig.10).
Through the apertures in the telescopic structure, secure the air evacuation pipe to the adapter flange using a band
(Fig.11); the pipe and band are not supplied.
Make the electrical connection using the power supply cable.
Take the upper flue (the one with slots) and insert it into the telescopic structure, with the slots at the bottom; secure
it to the structure with 2 screws (Fig. 12).
Take the lower flue and insert it in the same way into the other flue; move it upwards and secure it with 4 screws (Fig.13).
Insert the control box in its seat and secure it by tightening the 2 screws inside the lower flue (Fig.14).
Refit the metallic surround removed prior to the installation procedure (Fig. 4). Pay special attention to the direction,
since the slots (“A”. - Fig. 4) must align with the sensor mounted in the inside left part of the extractor hood.
Connect the halogen spot lights (Fig. 15).
Refit the grease filter.

Filtering Version:

Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe
all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must
correspond with the axis of the extractor hood controls.
Insert the baffle into the upper telescopic structure and secure it with 1 screw (Fig. 16). Connect a flex pipe, diameter
125 mm, securing it with a band (pipe and band not supplied).