Page 1
1
EN GUIDE TO INSTALLATION AND USE
Cooking Hob
IIMMPPOORRTTAANNTT
: Save this manual for the local electrical inspector’s use.
IINNSSTTAALLLLEERR
: Please leave this manual with the unit for the owner.
OOWWNNEERR
: Please keep this manual for future reference.
IIMMPPOORRTTAANNTT
: Local codes vary. Installation, electrical connections and
grounding must comply with all applicable codes.
EKI326UL
99637591_A_EN.qxp 19/07/2005 12:57 Page 1
Page 2
2
IMPORTANT SAFETY INSTRUCTIONS
1
- Proper Installation - Be sure your appliance is properly grounded and installed
by a qualified technician.
2
- Never Use your Appliance for Warming or Heating the Room.
3
- Do Not Leave Children Alone - Children should not be left alone or unattended
in an area where appliance is in use. They should never be allowed to sit or stand
on any part of the appliance.
4
- Wear Proper Apparel - Loose-fitting or hanging garments should never be worn
while using the appliance.
5
- User Servicing - Do not repair or replace any part of the appliance unless
specifically recommended in the manual. All other servicing should be referred to a
qualified technician.
6
- Storage in or on Appliance - Flammable materials should not be stored near
surface units.
7
- Do Not Use Water on Grease Fires - Smother fire or flame or use dry chemical or
foam-type extinguisher.
8
- Use Only Dry Potholders - Moist or damp potholders on hot surfaces may result
in burns from steam. Do not let potholder touch hot heating elements. Do not use
a towel or other bulky cloth.
9
- Use Proper Pan Size - This appliance is equipped with several, differently sized,
induction elements. Select utensils having flat bottoms, large enough to cover the
surface unit heating element. Proper size pots and pans will also improve efficiency.
10
- DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS - Surface units may
be hot even though they are dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch, or let clothing or other
flammable materials contact surface units or areas near units until they have had
sufficient time to cool.
11
. Do Not Heat Unopened Food Containers - Build-up of pressure may cause
container to burst and result in injury.
12
. Never Leave Surface Units Unattended at High Heat Settings - Boil-over causes
smoking and greasy spillovers that may ignite.
13
. Do not use aluminum foil, aluminum liners or aluminum containers on the
unit.
99637591_A_EN.qxp 19/07/2005 12:57 Page 2
Page 3
3
14. Utensil Handles Should Be Turned inward and Not Extend Over Adjacent
Surface Units - To reduce the risk of burns, and spillage due to unintentional
contact with the utensil, the handle of a utensil should be positioned so that it is
turned inward, and does not extend over adjacent surface units.
15. Do not Cook on Broken Cooktop - If cooktop should break, cleaning solutions
and spillovers may penetrate the broken cooktop and create a risk of electric shock.
Contact a qualified technician immediately.
16. Clean Cook-Top With Caution - If a wet sponge or cloth is used to wipe spills on
a hot cooking area, be careful to avoid steam burn. Some cleaners can produce
noxious fumes if applied to a hot surface.
CAUTION
Do not store items of interest to children in cabinets above or around the cooktop children climbing on the cooktop to reach items, could be seriously injured.
IMPORTANT SAFETY INSTRUCTIONS
99637591_A_EN.qxp 19/07/2005 12:57 Page 3
Page 4
4
Table oof CContents
Before IInstallation 55
Installation 66
Other IInstallation RRequirements 77
Electrical CConnection 8
Safety PPrecautions 99
Principle oof IInduction 110
Glass TTop, CCoil SSize aand CControls 111
Controls aand OOperation 112
Heating ZZones, CCoil SSizes && UUtensils 112
Power SSharing 112
Utensils ffor YYour IInduction UUnit 13
Matching PPots && PPans wwith CCoils eetc. 113
To DDo oor NNot tto DDo 114
Cleaning RRecommendations 15
Troubleshooting 116
Your ssafety aand eease oof uuse aare iimportant tto uus.
In this manual we have provided a number of safety warnings and as well as numerous tips
and hints for using the unit. Warnings and tips are marked with the following symbols:
Safety warning symbol
Tips and hints
99637591_A_EN.qxp 19/07/2005 12:57 Page 4
Page 5
5
If you are receiving the unit from a
transportation company, it is customer’s
obligation to inspect thepackage and note
any damage on the delivery receipt. After
delivery, have your induction cooktop
carefully unpacked, and again check forany
visible damage. If you find any damage onthe
unit at this point, immediately inform your
dealer or distributor. Although the
responsibility for shipping lies with the
carrier, your dealer/ distributor will assist you
with your claim.
If the unit is not supposed to be installed for
some time, you should keep it in its original
packaging, stored in a dry and safe place.
Read through the section of this manual
which pertains to installation, and make sure
that all of the requirements can be provided
or are already provided. Ensure that your
electric power supply is correct.
Before you install the unit, you should take a
moment to write down the information from
your nameplate and fill-out the table on page
19, for future after-sale servicing needs. This
information will be required every time you
call for any service on your unit.
Before Installation
99637591_A_EN.qxp 19/07/2005 12:57 Page 5
Page 6
6
11
/ INSTALLATION
4 cm
4 cm
4 cm
4 cm
A
51,8
31
49,6
27
92
To install the cooktop, cut out a rectangular
opening in the counter as shown on the
drawing and table below. Also, ensure that
you have a minimum of 10 mm (3/8”) of
space in the back of the unit, between the
rim and backsplash on your counter (or wall
if no backsplash) for ventilation.
A self-adhesive gasket is supplied with your
unit. Before setting the cooktop in place
install this gasket by sticking it underneath
the rim.
f your counter is produced from porous materials which tend to swell if in contact
with humidity and water, to better protect the cut-out, use proper sealants on the
edge which would prevent any penetration of humidity and water.
Chamfer all exposed edges of decorative laminates to prevent further chipping.
Radius corners of the cut-out and file them to ensure smooth edges and prevent
corner cracking.
Rough edges and inside corners which are not rounded as well as forced fits can
contribute to cracking of counter top laminate.
IApply the gasket only along the front rim
and on both sides. Do not put this gasket on
the rim in the back. This gasket will prevent
most of the spills from entering the cabinet
below and will keep the unit in place. Once
the gasket is installed, place the cooktop in
the opening, and lay it on the rim. Do this
carefully - do not drop the unit into the cutout. Make sure that the unit is sitting
properly on its rim all around the perimeter.
Cut-out dimensions
20
3/8
“
12
3/16
“
3
5/8
“
10
5/8
“
19
1/2
“
99637591_A_EN.qxp 19/07/2005 12:57 Page 6
Page 7
7
Other IInstallation RRequirements
Your ccook-ttop mmust aalways bbreath aadequately. MMake ssure tthat tthe aair iinlet aand iits
exhaust aare nnot oobstructed.
The uunit mmust nnot bbe iinstalled aabove aa wwashing mmachine, aa rrefrigerator oor aa ddeep-
freezer bbox
To eeliminate tthe rrisk oof bburns oor ffire bby rreaching oover hheated ssurface uunits, ccabinet
storage sspace llocated aabove tthe ssurface uunits sshould bbe aavoided.
The uunit mmust bbe iinstalled ssuch tthat iit ccan bbe ppulled wwithout ddifficulty oout oof tthe ccut-oout
for sservicing oor ccleaning.
Never gglue, ssilicone oor wwedge tthe uunit iinside iits ccut-oout.
During cooking, built-in fan inside the
cooktop will operate constantly to keep the
internal components cool. The air intake is
on the bottom of the cooktop box, and the
warm air exhaust is located on the back of
the rim, as shown on the schematic. If the air
intake or the exhaust is obstructed, the
cooktop safeties will either diminish the
power output or shut down the unit.
We suggest that you should periodically
check that there are no objects (dust, paper,
etc.) which could obstruct the air inlet under
your induction cooktop.
Although induction-cooktop heat rejection is
minimal and the unit does not create any
fumes in operation, such unit must be
installed underneath a properly sized
ventilation hood for exhausting any smell,
vapor and smoke created by cooking itself.
Also, a proper downdraft system can be
used for ventilation.
A minimum vertical clearance of 750 mm
[30”] is required between the top of the
cooking surface and the bottom of any
unprotected combustible material, such
as cabinets, wooden trim etc.
In the back, leave a minimum of 10 mm
[3/8”] between the cooktop edge and
adjacent vertical surfaces (backsplash,
wall, high cabinets etc.). This space is
needed for the unit to breath properly.
If a downdraft ventilation system is used,
a minimum of 6 mm (1/4”) of clearance
is required between the rear edge of the
cooktop and the downdraft snorkel.
Leave a minimum of 50 mm [2”]
underneath the unit for the air intake.
Air
Intake
Exhaust
Cabinet Above
Cabinet Below
40 [1 5/8"]
Minimum
Clearance
Requirements
Cross
Section
750 mm (30”)
50 mm (2”)
Cabinet below
Cabinet Above
750 mm 30”
40 5[1 5/8”]
99637591_A_EN.qxp 19/07/2005 12:57 Page 7
Page 8
8
Electrical Connection
PPhhaassee 22
EEaarrtthh
PPhhaassee 11
L
L
Green
Red
Black
cooktop eelectrical ccharacteristics aare:
Operating voltage................................................... 240 V~ 60 Hz
Maximum power output .............................................. 3600 W
Connect to .............. 240 V, 60 Hz, 2 Pole+G, 20 A (min) supply,
(3 conductors #12 AWG)
•
240 V
Connect the 3 wires as per the following
colour code
Electrical wwiring iinformation
An adequate electrical supply must be provided for this unit. All wire connections and
grounding must be done in accordance with
local electrical codes, or if these codes are
not established, then with the National Electrical Code, ANSI/NFPA No. 70 in the US , or
with the Canadian Electrical Code, CAN/CSA
C22.1, in Canada.
This unit comes equipped with three connection wires in a flexible conduit. The conduit
must be routed and properly connected to an
approved, owner-supplied, electrical, wall
junction-box. An approved connector must be
used for connecting the conduit to the junction box. A three wire, 2-pole, 240 V, 60 Hz service with minimum 20 A circuit protector must
be provided. The red and the black wire from
the unit are to be connected to the service
(”hot”) wires, and the green wire is to be
connected to the ground conductor.
The circuit protector for the unit should be
properly marked inside electric panel and anybody using the unit, or technician servicing
the unit, should be advised of circuit protector’s location, so that the power to the unit can
be disconnected when necessary.
Once the unit is properly fitted and connected
to the electrical power supply, turn the unit on
to ensure that all elements and controls are
operating well.
Note that your unit is designed for a stabile
and steady 240 V supply and the manufacturer, its distributors and dealers cannot be held
responsible for any unit malfunction due to an
inadequate electrical supply (inadequate cable size, low voltage, power surge etc). Furthermore, if your residence has only a 208 V
supply system, and if the voltage frequently
fluctuates, your cooktop may not function
properly
It is recommended that the connection to
electrical supply is done by a qualified electrician.
If there is any visible physical damage on the
conduit and the wires, the unit must not be
connected to the mains. A qualified electrician or approved service agent should be called in to replace the wires and the conduit.
99637591_A_EN.qxp 19/07/2005 12:57 Page 8
Page 9
9
Safety PPrecautions - RRead bbefore ooperating yyour ccooktop
Your induction-cooking unit has been
designed for residential use and food
preparation, and all of the safety parameters
have been rectified accordingly.
The unit incorporates numerous safety
devices and controls, and a few devices will
be mentioned here.
- A number of sensors monitor temperature
of internal components. If any of these
sensors senses that the component
temperature is above the limit, the power
output of the unit will automatically be
reduced, allowing the component to cool
down. Once this is achieved, the unit will
continue to operate normally at the output
level set initially by the operator.
- Each induction coil is equipped with a
sensor which is continuously monitoring the
temperature of the bottom of the pan to
prevent the pan from overheating.
- Each induction coil is equipped with a pan
sensing device. This device will not allow the
heating element to turn on unless it senses
a cooking utensil on the coil covering
enough surface area. The indication that the
coil is not running is the flashing of the
digital display. Once the pan is put properly
on the coil, the digital display will become
steady. Note that a small object such as a
fork, a spoon, a piece of jewelry, etc. will not
be mistaken for a cooking utensil, and it will
not trigger this sensor. Moreover, this device
will distinguish between cooking utensils
which are and are not suitable for induction
cooking. If a cooking utensil which is not
suitable for induction cooking is placed on a
coil there will be no power output on the
coil.
- If an operator leans on the keypad by
chance for more then ten seconds, controls
will disable the heating section of the unit.
This occurrence is called ‘long press’ and
when it happens “-” signs will appear on
power displays. The unit will act the same if
there is an accumulation of some liquid on
the keypad area, or if a damp cloth is left
sitting on the keypad. The section will
become operational again once the spill or
the object/hand is removed, and the
element turned back on.
In an effort of constantly improving our
products, we reserve the right to make any
changes to internal components, as well as,
to make any(cosmetic) modifications on the
outside frame.
This unit does not contain any asbestos or
asbestos based components.
This unit has been tested and certified
under FCC CFR 47, Part 18, for
electromagnetic interference.
The users with heart pacemakers must
consult with the pacemaker manufacturer
prior to using this cooktop which
incorporates induction heating source.
If a crack appears in the glass surface, disconnect the unit immediately to avoid any risk
of electric shock. If the unit is connected directly to supply inside a junction box, then
disconnect its breaker, or remove fuses manually.
Do not re-use your cooktop until the glass top is changed.
When cooking never use aluminum foil and never place products wrapped in aluminum foil, nor
products deep-frozen in aluminum packs on the hob. Aluminum foil could melt and damage
vitroceramic glass surface beyond repair.
99637591_A_EN.qxp 19/07/2005 12:57 Page 9
Page 10
10
The pprinciple oof iinduction
+
-
C
B
A
Induction coil
Inverter
Induced currents
A
B
C
For a proper choice of utensils, please refer to “Utensils for Your Induction”
When using induction elements, some utensils may produce
faint humming sound. This is a normal occurrence - the noise
is a result of vibrations caused by induced currents.
When an induction element - also called: ‘a
heating zone’, or simply: ‘a coil’ - is switched
on, the appropriate utensil is used, and a desired level of heating power selected, the electronic circuit unit (‘induction generator’ or ‘inverter’) powers up the induction coil which
creates a magnetic field. This magnetic field
continuously changes in terms of frequency
and intensity, and this creates induced currents in the bottom of the utensil and ultimately results in heat. The heat is transferred directly to the food being cooked.
Thus, induction heat makes the utensil a direct source of heat, featuring high level of efficiency with extremely low energy loss and unparalleled heating level control.
With induction cooking there is very little ‘heating inertia’. Induction cooking elements do
not incorporate a heat generating element unlike convectional electric rings, halogen or
radiant elements etc. - therefore, heat levels
can be changed very quickly.
Energy efficiency for induction is within range
of 90-95%, compared with 55-65% for conventional and radiant element, or 45% - 55% for
gas fueled burners. The energy efficiency
contributes to substantial energy savings,
both beneficial to the owner as well as the environment.
Induction cooking elements are sensitive to
the utensil type being used :
- if there is no utensil placed on the coil, or if
the utensil is not of induction grade, there will
be no power emitted by the coil;
- if the utensil is placed partially on the coil, or
if it is smaller than the coil, the internal sensors will reduce power to the coil; The Principle of Induction
- if the utensil is fully removed from the coil,
the power output will be instantaneously reduced to ‘0’, and, eventually, the controls will
turn the element off after a minute, unless the
utensil is returned back onto the coil.
When compared to the other methods of cooking, induction cooking has a very low level
of ambient heat, thus makes cooking more
pleasurable, with a reduced need for ventilation.
Finally, the vitroceramic glass as a cooking
surface barely becomes hot and this makes
cleaning much easier.
99637591_A_EN.qxp 19/07/2005 12:57 Page 10
Page 11
11
Glass Top, Coil Size and Controls
Touch Display Setting Use
6 medium
low heat
10 high
moderate heat
12 Maximum
maximum
•
•
POWERING ON
Press the start/stop touch control for the
zone you want to use. A flashing
"0"
indicates
that the zone is on. You can then choose the
desired power level.
If you do not select a power level, the cooking
zone will automatically shut off.
ADJUSTING THE POWER
Press the + or - power touch controls.
or on pre-select touch controls.
DESCRIPTION OF THE CONTROL
PANEL
•
Start/stop touch control.
Power - + touch controls.
Power pre-select touch controls.
A
B
Tip
For simultaneous use, favour the use
of cooking zones located on opposite sides
of the hob.
On the same side, the use of a cooking
zone at maximum power results in an
automatic limitation of the other cooking
zone on that side, which is indicated in the
power level display.
A B
D
D
16 ccm
50 W à 2200 W
22 cm
50 W à 2800 W
Cooking zone
Control zone
99637591_A_EN.qxp 19/07/2005 12:57 Page 11
Page 12
12
Tip
To check the suitability of your
cookware:
Place the vessel on a cooking zone at
power level 4.
If the display remains on, your cookware is
compatible.
If the display flashes, your cookware cannot
be used with induction cooking.
You can also use a magnet to test the
cookware.
If a magnet "sticks" to the bottom of the
cookware, it is compatible with induction.
WHICH COOKING ZONE
SHOULD YOU USE BASED ON
YOUR COOKWARE?
•
Cooking Cookware to use
zone
16 ccm ((6
1/2
”) 10 ...... 118 ccm ((4..7”)
22 ccm (9 ””) 18 ...... 224 ccm ((7..9
1/2
”)
POWER SHARING
Under the pretense that only one zone is
used with an adequate utensil covering the
whole surface of the coil, and that power on
the zone is adjusted to the maximum (‘12’):
- the maximum power output of 22 cm (9”)
heating zone is 2.8 kW;
- the maximum power output of 16 cm (6
1/2”) heating zone is 2.2 kW.
If only one coil is employed, it can be
utilized at its maximum power, but as soon
as the other coil is turned on, the controls
adjust the power on both coils
automatically for ‘power sharing’. This
power sharing is administered by unit’s
microprocessors, which will alternate
power between the two elements. There are
two factors affecting improved power
sharing on your cooktops.
The first is the application of an improved
technology for power sharing - not using
common relays, but rather semiconductors
which makes power sharing quicker, thus
more efficient. The second factor is that,
when in a power-sharing mode, two zones
can share full, 3.6 kW, power output of the
inverter.
Note that the controls will not allow both
zones to operate at full power, and the
power will be adjusted automatically - e.g. if
the power on one zone is adjusted to a
maximum, and the other zone is turned on
and power level also adjusted to its
maximum, the power level on the first zone
will automatically become lower. This
change will be visible on digital displays.
The controls are set in such a manner that
the last instruction (command) given to an
element is always a priority.
•
99637591_A_EN.qxp 19/07/2005 12:57 Page 12
Page 13
13
Induced current can be created only in
materials which have magnetic properties.
Thus, utensils for use with an induction unit
must be made from a ferromagnetic material
or have inserts with magnetic properties.
Your household may already have cookware
suitable for induction cooking, and you may
test any utensil with an induction element.
Incorporated controls are able to recognize
a suitable utensil. To perform a utensil test:
- Turn an element on and adjust power to any
level - you will notice that the digital power
display is flashing.
- Place your utensil on the coil. If the piece
being tested is suitable for induction
cooking, the display will become steady.
However, if it keeps flashing, the utensil
cannot be used on your induction unit.
- If the utensil is empty, remove it from the
coil immediately after you have done test and
turn the element OFF.
Another simple test to determine if a piece of
cookware can be used on an induction
cooktop is the ‘magnet test’. Use a magnet
and place it on the utensil. If the magnet
sticks to it, the piece will work with
induction.
Utensils for Your Induction
Utensils ccompatible wwith iinduction aare:
• Cookware made of enamel coated steel
with or without a non-stick coating.
• Cast iron cookware with or without enamel
coated base.
• Stainless steel pots and pans designed for
induction cookware.
Note:
Stainless steel used for utensils is nonmagnetic, in most cases, and unsuitable for
Utensils with thick flat bases should be chosen for the benefit of uniform heat
distribution.
Never leave an empty piece of cookware on an induction heating element for more then a few
seconds. If a utensil is left on an element at full power, temperature of the dish may
increase rapidly, the safeties would not engage, and this may damage your utensil,
the cooktop, and could result in an injury or a damage to your property.
When cooking large quantities of food, it is
always better to use a large diameter pan
and a larger coil, thus better and more
efficient heat distribution will be achieved
and food cooked evenly.
Matching PPots && PPans wwith CCoils, eetc.
Small elements,16 cm (6 1/2”), are best
utilized:
- With small utensils - but normally not
smaller then 10 cm (4”);
- For slow cooking and simmering (sauces,
creams, etc.);
- For cooking small quantities of food.
Large elements, 22 cm (9”), are primarily
designed for day-to-day cooking needs and
most commonly used pans - 18 to 25 cm (7
to 9 1/2”) in diameter.
induction cooking, but most manufacturers
make such utensils in layers for better heat
distribution, and a good number of such
pots and pans can be used with induction.
To make sure if a stainless steel utensil can
be used perform the utensil test.
Use of utensils with enameled coated base
will prevent the glass top of your unit from
getting scratched.
Pots and pans which do not have a flat
bottom still may be used, however they
should not be overly deformed.
Cookware made from glass, ceramic,
earthenware, aluminum and copper pots and
pans and non-magnetic stainless steel
cookware are not suitable for induction
cooking.
99637591_A_EN.qxp 19/07/2005 12:57 Page 13
Page 14
14
To Do or Not To Do
You must:
- Always place your utensil such that its
center is aligned with the centre of the coil.
- Avoid hitting the vitroceramic glass with
utensils or any hard objects - the glass
surface is highly resistant but not
unbreakable.
- Pick-up your utensils when moving them
around. Do not slide them and avoid
excessive rubbing of the top, as this leaves
scratches and erases the markings .
- Avoid using utensils with rough or
deformed bottoms.
- Avoid leaving any metal cooking
accessories, knives and forks, or metal
objects on the hob. They may get hot if left
close to any heating element in use.
Do not connect any appliances to the plugs above or near to the induction cooktop;
connection cable insulation can melt if in contact with heat, and this may result in an
injury and a property damage.
Your cooktop must never be used as a storage space or surface for piling up of any
material.
- Avoid storing flammable products in the
cabinets under your cooktop.
- Never leave an empty utensil on an
induction heating element, even when the
element is turned OFF.
- Only use maximum power for boiling and
frying.
- Never try heating up a closed can.
- Avoid pre-heating your non-stick pans (e.g.
with teflon coating) at maximum heat.
- Avoid storing solid and heavy items in the
cabinets above your cooktop. They may
unintentionally drop and damage the glass.
To Do or Not To Do
99637591_A_EN.qxp 19/07/2005 12:57 Page 14
Page 15
15
33
/ DAILY CARE OF YOUR APPLIANCE
MAINTAINING YOUR APPLIANCE
TTYYPPEE OOFF SSTTAAIINNSS//SSPPOOTTSS
Minor
Accumulated burn-on
stains.
Rings and traces of lime
scale.
Burn-on stains following
sugar spillage, melted
aluminium or plastic.
ACCESSORIES oor
AGENTS EEMPLOYED
Cleaning sponges & mild
detergents
Cleaning sponges, mild
detergents and cleaning
agents for vitroceramic
glass
Cleaning cloth,white
vinegar, or diluted
de-liming agent.
Vitroceramic cleaning
agents and sponge.
WHAT TTO DDO
Soak the area to be cleaned with
soapy water, then wipe it.
Soak the area to be cleaned with
warm soapy water. Use a special
scraper for vitroceramic glass to
remove grease and food particles.
Finish off with a cleaning sponge,
then wipe it clean.
Apply warm white vinegar on the
stain. Leave to act then wipe off
with a soft cloth. OR Use a
commercial cleaner on affected
area. Note that such cleaner may
leave stains on stainless steel
frame, thus protect exposed
stainless steel.
Apply special vitroceramic
glass cleaner on the surface,
preferably one which contains
silicone (protective action).
Leave to act, then finish off with
a cleaning sponge, then wipe it
clean.
Nonabrasive
Paste
Ordinary Sponge or Special
Sponge for Delicate Items
Abrasive-backed
sponge
Powder
•
Cleaning of an induction cooktop is easy. Read and follow these
recommendations:
99637591_A_EN.qxp 19/07/2005 12:57 Page 15
Page 16
16
WH ATT SH OUL DD YO UU DO ?PO SSI BLEE CA USE SPR OB LE M
You have doubts about whether your hob is working correctly. This does not
necessarily mean that there is a breakdown. Nevertheless, check the following
points.
Contact your service agent.
Have the connection checked
first. If the connection is OK,
contact your service agent.
This is a normal occurrence.
Use another utensil suitable for
induction cooking.
Check your beakers (fuses)
and/or connection cable.
If OK, contact your service agent.
When you switch the unit on, the
supply-line breaker trips off or the
supply-line fuse burn.
When you switch elements on, only
one element works.
Your hob makes faint clicking noise
when in operation.
The fans keep running for a few
minutes after the unit has been
switched off,
After turning an element ON and
having utensil placed on the coil,
there is no heat and the digital
indicator continues flashing..
The unit doesn't work at all.
The top of the unit is always
lukewarm (even when elements are
not switched on).
This is a normal occurrence.
This is a normal occurrence.
Utensil makes noise during cooking.
Under high power this
phenomenon is normal with some
types of pots and pans. There is
no danger for the hob.
Use each heating element for an
hour with a pan filled with water.
Your unit may be connected
incorrectly,or there is an
internal problem.
There is an internal problem
with the unit.
This noise occurs when the power is
being shared between two
induction coils.
The electronics are cooling
down
The utensil you are trying to use
is not compatible with induction
cooking or its diameter is under
10 cm. (4”).
There may be a power supply
or internal problem.
The electronic components are
under power and they create
heat.
Your utensil creates noise from
vibrations caused by induced
current .
A new unit
The hob gives off a smell when first
used for cooking.
If any crack on the vitroceramic glass can be noticed, or the glass
is broken DO NOT USE THE UNIT. Disconnect the electrical
supply to the unit by tripping the breaker off (if the unit is hardwired to the supply) or just unplug the unit (if there is a plug on
the supply cable).
Servicing of an induction unit is to be done by an authorized
service agent. Contact your dealer for service location closest to
your residence. Never try servicing the unit yourself.
44
/ SPECIAL MESSAGES, DIFFICULTIES
9963 77591
07/05
99637591_A_EN.qxp 19/07/2005 12:57 Page 16
Loading...