König & Meyer 14092 User Manual

SICHERHEITSHINWEISE
AUFSTELLANLEITUNG
WARTUNG
Sichtprüfung vornehmen, ob alle Teile vorhanden und in Ordnung sind.
1 SOCKEL 2 GASFEDER 3 POLSTERSITZ
5 in die Bohrung des Sockels stecken
6 Polstersitz mit dem Stutzen voran auf den
6 oberen Zapfen der Gasfeder aufsetzen
7 Sitz mit dem Körpergewicht nach
7 unten drücken, bis die Teile spielfrei 7 ineinander stecken. 7 Zur Probe den Sitz kurz anheben, um 7 sicher zu stellen, dass alle Teile fest sitzen.
HÖHENVERSTELLUNG
- Zuerst Platz auf dem Hocker nehmen.
- Körpergewicht mit den Füssen abstützen
8 Griff nach oben drücken 9 Je nach Körpereinsatz fährt der Sitz jetzt
9 ein oder aus 9 Sobald die gewünschte Sitzhöhe erreicht ist, 9 den Griff 8 wieder loslassen
DEMONTAGE in die 3 Bestandteile
- Am besten mit 2 Personen arbeiten
10 Hocker umdrehen und auf dem
10 Sitzpolster abstellen
11 Hocker am Sockel halten und
11 vom Boden abheben
12 Mit Kunststoffhammer einen kräfigen Schlag
12 auf die Unterseite der Gasfeder geben, so 12 dass diese sich aus dem Sockel löst
13 Gasfeder wieder etwas anheben und
13 auf die Metallplatte des Sitzes erneut 13 einen festen Schlag mit dem Kunststoff- 13 hammer tätigen, bis sich der Sitz löst.
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de 14092-017-55 Rev.05 03-80-181-00 1/18
- Auf geeigneten, tragfähigen und ebenen Untergrund achten
- Hocker nicht als Steighilfe benutzen
- Die Möglichkeit das Produkt zu zerlegen, birgt naturgemäß Einklemmgefahren Umsichige und
- aufmerksame Handhabung bei Aufbau, Betrieb und Abbau sind daher unverzichtbar
- Hocker beim Transport gleichzeitig an Sitz und Sockel halten
- Der Parkettschoner ist aus hochwertigem Material und weitestgehend frei von Weichmachern.Trotzdem sollte ggf. eine rutschfeste
- Unterlage unter die Füße gelegt werden, da diese auf empfindlichen Böden (z.B. Parkett) Spuren hinterlassen können.
14092 Pianohocker mit Gasdruckfeder
Schön, flexibel und bequem
- Hervorragende Standfestigkeit und Stabilität
- Komfortables und widerstandsfähiges Sitzpolster
- Schmuckes Design
- Bedienerfreundliche und stufenlose Höhenverstellung dank Gasdruckfeder
- Tour-kompatibel (schnell zerlegbar in 3 Teile)
- Daten: Höhe: 480-6010 mm, Sitz ø 350 x H 120 mm, Sockel ø 400 mm, Gewicht: 6,3 kg
Vielen Dank, dass Sie sich für dieses Produkt entschieden haben. Diese Anleitung informiert Sie über alle wichtigen Schritte bei Aufbau und Handhabung. Wir empfehlen, sie auch für den späteren Gebrauch aufzubewahren.
- Bei Wartungsarbeiten auf evtl.
- Gefährdungen achten.
- Zur Reinigung am besten ein leicht
- feuchtes Tuch und ein nicht
- scheuerndes Reinigungsmittel
- benutzen.
FEHLERSUCHE (F) und BESEITIGUNG (B) F: Pianohocker steht wackelig:
F: B: Untergrund prüfen bzw. in F: B: Ordnung bringen F: B: Steckverbindungen auf Festsitz F: B: prüfen
F: Sitz fährt nicht ein/aus:
F: B: Person zu leicht bzw. Bügel zu F: B: wenig betätigt F: B: Feder defekt (Kundendienst)
TECHNISCHE DATEN
Material Sockel, Gasdruckfeder: Stahl gepulvert schwarz Überzug Gasfeder: Kunststoff PP Sitzbank: Skaileder schwarz
Abmessungen in mm Sockel: ø400, Sitz: ø350x120, Höhe: 480-610
Gewicht / Karton 6,4 kg / Einzelkarton: LxBxH 500x455x300 mm
480 - 610 mm
SAFETY NOTES
ASSEMBLY INSTRUCTIONS
CARE & MAINTENANCE
Check that the following parts are included in the package and undamaged.
1 BASE 2 PNEUMATIC SPRING 3 UPHOLSTERED SEAT
4 Place the base on the floor 5 Insert the thicker end of the pneumatic
5 spring section into the drill hole
6 Place the upholstered seat with the
6 connection piece first onto the upper pin 6 of the pneumatic spring section
7 Press the seat down with your body
7 weight until the parts connect. 7 Check that the parts are secure by 7 briefly lifting the seat.
HEIGHT ADJUSTMENT
- First, sit on the stool.
- Sit with your feet on the ground supporting
- your bodyweight
8 Push the lever up 9 Use your body position to lower or
9 higher the seat to the required height, 9 release the lever 8
DISMANTLE into 3 parts
- preferably with two persons
10 Turn the stool upside down on
10 the upholstered seat
11 Hold the stool by the base and lift it
11 from the floor
12 Using a rubber hammer, strike the underside
12 of the pneumatic spring so that it releases 12 from the base
13 Again, lift the pneumatic spring slightly and
13 strike the metal plate of the seat with the 13 rubber hammer until the seat releases.
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de 14092-017-55 Rev.05 03-80-181-00 1/18
- The stool is only suitable for use on level, sound ground
- Do not use the stool as a step ladder
- As the product can be dismantled, there is the inherent risk of pinching or trapping and care is required
- when assembling, using or dismantling
- When transporting the stool hold both the base and the seat
- The high quality floor protector is virtually free of plasticizers, but lay a non-slip mat under the base to avoid leaving marks on
- sensitive floors (e.g. parquet).
14092 Pneumatic Piano Stool
Attractive, flexible and comfortable
- Excellent stability
- Comfortable and durable seat upholstery
- Elegant design
- User-friendly, the pneumatic spring allows continuous height adjustment
- Tour compatible (quick to dismantle into 3 pieces)
- Data: height: 480-610 mm, seat ø 350 x H 120 mm, base ø 400 mm, weight: 6.3 kg
Thank you for choosing this product. These instructions contain information about the assembly of the product and its use. We suggest you keep the instructions in a safe place for later use.
- Be aware of the potential risks
- associated with maintenance and
- care
- We recommend using a slightly
- damp cloth and a non-scouring
- cleaning agent
FAULT FINDING (F) and REPAIR (R) F: Piano stool wobbles:
F: R: Check the ground and if F: R: necessary correct positioning F: R: Check the connections are secure
F: Seat does not move up or down:
F: R: Person is too light or the lever F: R: has not been pushed up far F: R: enough F: R: Spring is defective (contact F: R: customer service)
TECHNICAL DATA
Materials Base, pneumatic spring: black powder-coated steel Pneumatic spring casing: PP plastic Seat: black Skai leather
Dimensions in mm base: ø400, seat: ø350x120, height: 480-610
Weight / carton
6.4 kg / single carton: LxBxH 500x455x300 mm
480 - 610 mm
Loading...