K 2.97 M
High Pressure
Washer Operator
Manual
Overview ....................................... 2
Important Precautions ............ 3 - 4
Assembly Instructions ................. 4
Operating Instructions ................. 5
Using the accessories ................. 6
Working with Detergents ............. 7
Shut Down and Clean-Up ............ 8
Taking a Break ............................. 8
Winterizing and Long-Term
Storage ......................................... 8
Cleaning Tips ....................... 9 - 10
Optional Cleaning Accessories . 10
Troubleshooting .................. 11 - 12
Specifications
Operating pressure 8000 kPa
Max. Pressure 1400 PSI
Water volume 1.6 GPM
Voltage 120 V
Amp draw 13 AMPS
Please keep the original box, packaging and receipt.
Before operating this unit, please read this manual thoroughly and retain
it for future reference.
Manual Part No. 5.960-786.0 01/03ENPart No. 1.421-212.0
Model K 297 OVERVIEW
Item DescriptionItem Description
Item Description
Item DescriptionItem Description
1. Power cord
2. Trigger gun
3. Trigger gun safety lock
4. High pressure hose
5. Water inlet with filter
6. Retractable handle
7. Accessory holder
8. Detergent suction tube with filter
9. High pressure outlet
10. On/Off switch
11. High pressure spray nozzle
12. Rotary nozzle
2
NEVER!
Never point nozzle at people or animals.
Never drink alcohol or use drugs while operating this equipment.
Never operate while standing in water.
Never touch plug with wet hands.
Never let electrical connections rest in water.
NeverNever
Never operate pressure washer without the water turned on
NeverNever
Never use hot water
IMPORTANT PRECAUTIONS – Read First!
2 Safety Warnings
When using this product, basic precautions
should always be followed:
• Read all the instructions before using the
product.
• High pressure jets can be dangerous if
subject to misuse. The jet must not be
directed at persons, animals, electrical
devices, or the machine itself.
• To reduce the risk of injury, do not operate
the machine near children.
• Learn how to stop the machine and
release pressure quickly. Be thoroughly
familiar with the controls.
• Stay alert — watch what you are doing.
• Wear safety goggles.
• Do not use acids, solvents, or any
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
• Do not operate the product when fatigued
or under the influence of alcohol or drugs.
• Keep operating area clear of all persons.
• Do not stand on unstable surfaces.
Stand with both feet balanced at all times.
• To reduce the risk of electrocution, keep
all connections dry and off the ground.
Do not touch plug with wet hands.
• The Trigger Gun Safety Lock PREVENTS
the trigger from accidentally being
engaged. This safety feature DOES NOT
lock trigger in the on position.
WARNING
• DO NOT USE WITH FLAMMABLE LIQUIDS AND
TOXIC CHEMICALS
• INJECTION HAZARD: EQUIPMENT CAN
CAUSE SERIOUS INJURY IF THE SPRAY
PENETRATES THE SKIN. DO NOT POINT THE
GUN AT ANYONE OR ANY PART OF THE
BODY. IN CASE OF PENETRATION SEEK
MEDICAL AID IMMEDIATELY.
• THIS SYSTEM IS CAPABLE OF PRODUCING
8000 KPA. TO AVOID RUPTURE AND
INJURY, DO NOT OPERATE THIS PUMP
WITH COMPONENTS RATED LESS THAN
8000 KPA WORKING PRESSURE (INCLUDING BUT NOT LIMITED TO SPRAY GUNS,
HOSE AND HOSE CONNECTIONS).
• BEFORE SERVICING, CLEANING OR
REMOVAL ANY PARTS, SHUT OFF POWER
AND RELIEVE PRESSURE.
Extension Cords
Use a sufficient gauge: Up to 25 ft = 12/3
AWG; 25 to 50 ft = 10/3 AWG. Use only
extension cords that are intended for outdoor
use. These extension cords are identified by
the marking “Acceptable for use with outdoor
appliances; store indoors while not in use.”
Use only extension cords having an electrical
rating not less than the rating of the product.
Do not use damaged extension cords.
Examine extension cord before using and
replace if damaged. Do not abuse extension
cord and do not yank on any cord to
disconnect. Keep cord away from heat and
sharp edges. Always disconnect the
extension cord from the receptacle before
disconnecting the product from the extension
cord. If you are using an extension cord, it
should always be completely unwound from
the cable drum.
Grounding Instructions
This product must be grounded. If it should
malfunction or breakdown, grounding
provides a path of least resistance for
electric current to reduce the risk of electric
shock. This product is equipped with a cord
having an equipment-grounding conductor
and a grounding plug. The plug must be
plugged into an appropriate outlet that is
properly installed and grounded in
accordance with all local codes and
ordinances.
DANGER- Improper connection of the
equipment-grounding conductor can result in
a risk of electrocution. Check with a qualified
electrician or service personnel if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the product - if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician. Do not use any type of adapter
with this produc
t.
Caution
• Follow the maintenance instructions
specified in the manual.
• This machine has been designed for
use with cleaning detergent supplied or
recommended by the manufacturer. The
use of other cleaning detergents may
affect the operation of the machine and
void the warranty.
3
IMPORTANT PRECAUTIONS – continued
PRECAUTIONS
Water Supply (Cold Water Only)
• Water hose must be at least 1/2 inch or
5/8 inch in diameter.
• Flow rate of water supply must not fall
below 2 GPM (gallons per minute).
• Flow rate can be determined by running the
water for one minute into an empty 5-gallon
container.
• The water supply temperature must not
exceed 104°F/40°C.
• Never use the pressure washer to draw in
water contaminated with solvents, e.g.
paint thinners, gasoline, oil, etc.
NOTE: Dirt in the feed water will
damage the unit. To avoid this risk,
we recommend fitting a water filter.
• Always prevent debris from being drawn
into the unit by using a clean water source
and an accessory water filter if required.
• Save these instructions!
ASSEMBLY INSTRUCTIONS
Step 1
4
Insert wheels into side holes
at the bottom of the pressure
washer and snap into place.
Step 4
Slide the trigger gun holder
into track on the right hand
side of the pressure washer.
Step 2
Place the wheel carriage
onto the mounting brackets
on the sides of the washer
and align the four holes.
Snap into place.
Step 3
Slide the handle into the top
slot of the wheel carriage
and snap into place.
Step 5
Pull out the locking slide from the right side of the trigger
gun handle, and insert the small end of the high pressure
hose into place. Push the locking slide back into the trigger
gun to lock the hose in position.
OPERATING INSTRUCTIONS
Step 1
Connect the high pressure hose to the high
pressure outlet.
Step 3
Connect the garden hose to the water inlet.
Step 2
Insert the spray wand of your choice. Press
in against the spring tension and twist into
the locked position.
5
Step 4
Connect garden hose to the cold water
source and turn water on completely.
Step 5
Plug the power cord into the power outlet.
Trigger the gun to eliminate trapped air, wait
for a steady flow of water to emerge from
the spray nozzle.
Step 6 Turn on the pressure washer (I).
NOTE: This unit is equipped with a pressure
switch. The motor only starts up when the
trigger on the gun is pulled.
The motor shuts off when the trigger is
released.
USING THE ACCESSORIES
High pressure nozzle Rotary nozzle
This nozzle features a steady powerful high
pressure spray pattern, for general cleaning.
This nozzle features a 0º pencil jet which
rotates 360º for maximum dirt cutting action,
effectively increasing cleaning performance
up to 40%. This nozzle combines the cleaning
performance of a 0º pencil jet with the surface
coverage of a wide angle nozzle.
Not recommended for soft materials,
siding, painted surfaces, decks or autos.
6
Warning
TO AVOID SERIOUS INJURY, NEVER POINT SPRAY NOZZLE AT YOURSELF,
OTHER PERSONS OR ANIMALS
WORKING WITH DETERGENTS
Detergents can only be applied at low pressure.
For best results see Cleaning
Tips on pages 9 & 10 for specific
information on how to clean
different surfaces.
Step 1 Remove the High pressure nozzle.
Note: No detergent in high-pressure mode
Step 2 Fill a container with Kärcher
detergent. Place the filter end of detergent
suction tube into the container.
Always Use Kärcher Detergents for Best
Results.
Kärcher biodegradable detergents are
specially formulated to protect the
environment and your pressure washer.
Special formula won’t clog the suction tube
filter and will protect the internal parts of the
pressure washer for a longer life. For Kärcher
Detergents, check your retailer or call:
1-800-465-4980
The following Kärcher detergents are
available:
• Pressure Wash
• Deck Wash
• Degreaser
• Touchless Vehicle Wash
7
Step 3 Turn on the pressure washer.
Pull trigger to operate unit: Liquid detergent
is drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
Caution
Never use:
• Bleach, Chlorine products and other
corrosive chemicals
• Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
SHUTTING DOWN & CLEAN-UP
Step 1
Remove detergent suction
tube from container and
insert into 1 gallon of fresh
water. Siphon water at low
pressure for one minute.
8
Step 5
Disconnect the garden hose
from the water inlet on the
unit.
Step 2
Turn the switch to
off (O) position and
unplug cord from
outlet.
Step 6
Disconnect the high pressure
hose from the high pressure
outlet.
TAKING A BREAK... five minutes or more
Step 1
Engage the gun
safety lock.
Step 3
Turn off the water
source.
Step 4
Press trigger to
release water
pressure.
Step 7
Engage the gun
safety lock.
Step 2
Turn pressure washer
to off (O) position.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
2. Turn on the machine for a few seconds,
until the water which had remained in
the pump exits. Turn off immediately.
3. Do not allow high pressure hose to
become kinked.
4. Store the machine and accessories in
a room which does not reach freezing
temperatures. DO NOT store near
furnance or other sources of heat as it
may dry out the pump seals.
Caution: Failure to follow the above
directions will result in damage to the
pump assembly and accessories.
CLEANING TIPS
Deck Cleaning
(with or without detergent)
Pre-rinse deck and surrounding area with
fresh water. If using Kärcher
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of
approximately 25 square feet. Allow
Wash
to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. Rinse
at high pressure in a long sweeping motion
keeping the spray nozzle approximately 3-6
inches from the cleaning surface. Always
clean from top to bottom and from left to
right. When moving on to a new section of
the cleaning surface, be sure to overlap the
previous section to eliminate stop marks
and ensure a more even cleaning result.
Deck Wash
Deck
,
House Siding
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher
detergent suction tube directly into cleaning
solution and apply to surface at low
pressure (for best results, limit your work
area to sections of approximately 6 feet and
always apply detergent from bottom to top).
Allow
Pressure Wash
1-3 minutes. Do not allow detergent to dry
on surface, if surface appears to be drying,
simply wet down surface with fresh water. If
needed, use special Wash Brush
Attachment (not included) to remove
stubborn dirt. Rinse at high pressure from
top to bottom in an even sweeping motion
keeping the spray nozzle approximately 6
inches from the cleaning surface.
Pressure Wash
to remain on surface
, place
Cement Patios, Brick and Stone
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher
Degreaser
directly into cleaning solution and apply to
surface at low pressure. For best results,
limit your work area to smaller sections of
approximately 25 square feet. Allow
Pressure Wash
surface 1-3 minutes. Do not allow detergent
to dry on surface. Rinse at high pressure in
a sweeping motion keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. Always clean from top to
bottom and from left to right.
Pressure Wash
, place detergent suction tube
or
Degreaser
or
to remain on
Cars, Boats & Motorcycles
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Kärcher
detergent suction tube directly into cleaning
solution and apply to surface at low
pressure. For best results, clean one side of
vehicle at a time and always apply
detergent from bottom to top, do not allow
detergent to dry on surface. If needed, use
special Wash Brush Attachment (not
included) to remove stubborn dirt. Rinse at
high pressure in a sweeping motion keeping
the spray nozzle approximately 6-8 inches
from the cleaning surface (distance should
increase when rinsing pin-striping or other
sensitive surfaces). Always clean from top
to bottom and from left to right. For best
results, wipe surface dry with a chamois or
soft dry cloth.
Caution: Do not use the rotary nozzle on
vehicles as it may cause damage.
Touchless Vehicle Wash
, place
9
CLEANING TIPS – continued
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow
Wash
to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action.
Pressure Wash
Patio & Lawn Furniture
(with or without detergent)
Pre-rinse furniture and surrounding area
with fresh water. If using
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. Allow
10
Pressure Wash
Pressure Wash
or
Pressure
to
remain on surface 1-3 minutes. Do not allow
detergent to dry on surface. If needed use
special Wash Brush Attachment (not
included) to remove stubborn dirt. Rinse at
high pressure in a sweeping motion keeping
the spray nozzle approximately 3-6 inches
from the cleaning surface. For best results,
clean from top to bottom and from left to
right.
Recommendations
• Before cleaning any surface an inconspicuous area should be cleaned to test
spray pattern and distance for maximum
cleaning results.
• If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the loose
paint from the surface.
• When using on surfaces which might
,
come in contact with food, flush surfaces
with plenty of drinking water.
OPTIONAL CLEANING
Optional cleaning accessories are available to further enhance your cleaning capabilities:
See for details.
• Rotating Wash Brush
• Wash Brush
• Underbody Wand
• Pipe Drain Cleaner
• Sandblasting Attachment
• Water Pumping Kit
• Water Siphon Kit
• 25’ Extension Hose
KÄRCHER 2 YEAR WARRANTY
KÄRCHER CANADA INC. warrants to the original owner that this product shall be free from
defects in material and workmanship for two years from the date of its original purchase. If
such a defect appears during the warranty period, upon presentation of proof of purchase,
KÄRCHER CANADA INC. will repair or replace (at its option) your product without charge.
This warranty does not cover accidental damage, unreasonable use, normal wear and tear,
loss of use or other consequential damages, nor does it cover repairs made or attempted by
unauthorized persons.
Trigger gun, hose, spray wands and other accessories are warranted for 3 months.
Please note that no returns will be accepted without prior authorization from our customer
service department.
It is the owner’s responsibility to file claims for damage caused by public transportation
carriers directly with the carrier concerned.
TROUBLESHOOTING
Disconnect the machine from the power source before making any repair.
Symptom
Motor will not start
Unit does not reach high
pressure.
Output pressure varies
high and low.
Cause
On/Off switch is in the “OFF” (O)
position.
Power cord is not plugged in.
Extension cord is too long.
Extension cord is not proper gauge.
Extension cord is damaged.
Electrical outlet does not supply
adequate power.
Tripped circuit breaker
Diameter of garden hose is too
small.
Water supply is restricted.
Not enough inlet water supply.
Water inlet filter is clogged.
Not enough inlet water supply.
Solution
Turn switch to the “ON” (I) position
Plug in power cord.
Replace extension cord with either
a 25 ft. 12/3 gauge cord or a 50
ft. 10/3 gauge cord.
Try a different outlet.
Reset breaker
Replace with a 1/2 inch or 5/8
inch garden hose.
Check garden hose for kinks,
leaks and blockage.
Open water source full force.
Remove filter and rinse out in
warm water.
Turn water on full force. Check
garden hose for kinks, leaks or
blockage.
11
Pump is sucking air.
Water inlet filter is clogged.
Discharge nozzle is obstructed.
Calcified gun, hose or spray wand.
Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until “a steady flow of water
emerges through the nozzle.
Remove filter and rinse out in
warm water.
Blow out or remove debris with a
fine needle.
Run distilled vinegar through
detergent suction tube.
TROUBLESHOOTING – continued
Symptom
No detergent.
Garden hose
connection leaks.
Spray wand leaks.
12
Pump is noisy.
Cause
Detergent suction tube not properly
connected to the machine.
Detergent is too thick.
Filter on detergent suction tube is
clogged.
Damaged or clogged detergent
suction tube.
Spray wand is installed.
Loose fittings.
Missing/worn rubber washer.
Spray wand not properly attached.
Broken o-ring or plastic insert.
Pump is sucking air.
Solution
Check connection.
Dilute detergent.
Run warm water through filter to
remove debris.
Remove obstruction or replace
detergent suction tube.
Remove spray wand.
Tighten fittings.
Insert new washer.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Call service center
Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.
Water leaks from pump
(up to 10 drops per minute
is permissible).
Oil Drips.
Loose fittings.
Water seals are damaged or worn.
Oil seals are damaged or worn.
Check that all fittings are tight.
Call service center.
Call service center.
1-800-537-4129
If you encounter any additional difficulties not listed, please call our service
center at 1-800-465-4980 for help, or visit www.karcher.ca
Loading...