Karcher K 2200 IB User Manual
®
Overview . . . . . . . . . . . . . . . . . . . . . .1
Precautions . . . . . . . . . . . . . . . . . . .1-2
Assembly Instructions
. . . . . . . . . . . .3
Operating Instructions
. . . . . . . . . . . .4
Using the Accessories . . . . . . . . . . . .5
Working with Detergents . . . . . . . . . . .6
Shut Down and Clean-Up . . . . . . . . . .7
Taking a Break . . . . . . . . . . . . . . . . . .7
Winterizing and Long-Term Storage . .7
Cleaning Tips . . . . . . . . . . . . . . . . .8-9
Optional Cleaning Accessories . . . . . .9
Trouble Shooting . . . . . . . . . . . . .10-11
Model K 1800 IB Part No. 1.133-121
Model K 2200 IB Part No. 1.133-211
High Pressure Washer Operator Manual
Specification
Model K 1800 IB
Max. Operating pressure 1800 PSI
Max. Water volume 2.0 GPM
Engine 3.75 HP Briggs & Stratton Sprint
Model K 2200 IB
Max. Operating pressure 2200 PSI
Max. Water volume 2.2 GPM
Engine 6.0 HP Briggs & Stratton Quantum
Manual Part No. 9.139-111
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 1
Modelo G 1800 LB/K 1800 LB
Parte No. 1.133-124
Parte No. 1.133-121
unit may vary from picture shown
®
Item Description
1. Water inlet
2. Detergent suction tube
3. Oil fill cap
4. Knob Assembly (two each):
Hex Head Screw
Serrated Washer Knob
5. High pressure hose
6. Detergent Filter
7. Handle
8. Trigger gun safety lock
9. Trigger gun
10. Pull start
11. Gas tank
12. Vario spray wand
13. High pressure outlet
(not pictured)
14. Accessory rack
15. Manual
16. 4 screws for accessory
rack (not pictured)
2
IMPORTANT PRECAUTIONS – Read First!
Safety Warnings
When using this product basic
precautions should always be followed:
• Read all the instructions before using the
product.
• FIRE HAZARD! Do not add fuel with the
engine running. Do not operate if fuel has
been spilled. Instead move the machine
to a different location and avoid creating
sparks.
• Operate and fuel machine in a well ventilated area, free of devices featuring an
open pilot or flame such as boilers, water
heaters, etc.
• High pressure jets can be dangerous
if subject to misuse. The jet must not be
directed at persons, animals, electrical
devices, or the machine itself.
• Wear safety goggles.
• Do not use acids, solvents, or any other flammable material in this
product. These products can cause physical injuries to the operator and irreversible damage to the machine.
• The machine has hot surfaces which can
cause burns. Operate the unit in a safe
environment and away from children.
• Do not allow the high pressure hose to
come into contact with the muffler guard.
• Do not leave the machine running
unattended.
• Learn how to stop the machine and
release pressure quickly. Be thoroughly
familiar with the controls.
• Stay alert — watch what you are doing.
• Do not operate the product when fatigued
or under the influence of alcohol or drugs.
• Do not stand on unstable surfaces. Stand
with both feet balanced at all times.
• The Gun Safety Lock PREVENTS the
trigger from accidentally being engaged.
This safety feature DOES NOT lock trigger
in the “ON” position.
Water Supply
(Cold Water Only)
• Water hose must be at least 3/4 inch in
diameter.
• Flow rate of water supply must not fall
below 2.5 GPM (gallons per minute).
• Flow rate can be determined by running
the water for one minute into an empty
5-gallon container.
• The water supply temperature must not
exceed 104°F/40°C.
• Never use the pressure washer to draw in
water contaminated with solvents, e.g.
paint thinners, gasoline, oil, etc.
• Always prevent debris from being drawn
into the unit by using a clean water
source.
We strongly recommend that this high pressure washer not be left running for periods
of 5 minutes or longer without the trigger
gun being engaged.
This Kärcher high pressure washer is
equipped with thermal protection to extend
the life of your pressure washer. The thermal
protector will automatically activate at a predetermined high temperature ejecting hot
water before resetting. This ensures that the
pump does not become damaged.
Caution
• Follow the maintenance instructions specified in the manual.
• This machine has been designed
for use with cleaning detergent
supplied or recommended by the
manufacturer. The use of other
cleaning detergents may affect the
operation of the machine and void
the warranty.
1
NEVER!
MODEL K 1800 IB/2200 IB OVERVIEW
Never point nozzle at people or animals.
Never drink alcohol or use drugs while operating this equipment.
Never
spray electrical connections, electrical outlets or fixtures.
Never add
fuel with the engine running or operate where fuel has been spilled.
Never
touch hot surfaces or allow accessories to contact hot surfaces.
Never
operate in an enclosed space, exhaust fumes are dangerous.
Never
operate near utilities with open flames.
Never
operate without the water turned on and never use hot water.
NOTE: Engines controls shown may appear different.
15
13
12
11
10
14
9
8
7 6
5
3
4
2
1
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 2
G 1800 LB / K 1800 LB
4
Step 6
Model K 2200 IB: Slide the throttle
control to the fast position. Then move the choke
lever to the “CHOKE” position (only if engine is
cool). After starting, move the choke to “RUN”.
Step 7
Pull the starter handle. If
the engine fails to start after 3 pulls
squeeze the trigger gun to release
pressure, and repeat step 7.
OPERATING INSTRUCTIONS
Step 1 Connect the high pressure hose to the
unit’s high pressure outlet.
Step 2 Insert the Vario spray wand
into the gun. Push in and turn clockwise to lock spray wand in place.
Step 3 Connect
garden hose to unit’s
water inlet.
Step 4 Connect garden
hose to the cold water
source and turn water on
completely.
Step 5 Trigger the gun to
eliminate trapped air, wait for a steady
flow of water to emerge
from the spray nozzle.
Step 6
Model K 1800 IB:
Slide the throttle control to the fast
position. Then push primer ball three
times. Wait 3 seconds between each
push.
Note: in cold weather push 5 times
NOTE: Engines controls shown may appear different.
You are now ready to
operate your Kärcher
Pressure Washer.
3
ASSEMBLY INSTRUCTIONS
Step 1
Slide the handle through the
accessory rack.
Step 3
Check oil level. Oil level should
always be between the “FULL” and “ADD”
marks on the dipstick. Be sure the machine is
level when checking the oil level. (Refer to the
engine’s operating manual for seasonal
grades.)
Step 4
Insert the detergent tray into one
of the slots of your choice and screw in the
fastener. Fill with the proper detergent for
your cleaning project.
Important! Do
not run the engine
with a high or low oil level as this can
cause engine damage. If you have fur-
ther questions regarding the engine,
please refer to the engine’s operating
manual included with the unit.
Step 5
Fill gas tank with unleaded
gasoline. Do not use leaded gasoline.
Step 2
Align the holes of the accessory
rack to the handle and fasten the four (4) screws.
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 4
6
WORKING WITH DETERGENT
Step 1 Install the Vario spray wand and
set the Vario spray wand to the low pressure
setting (-) by turning the wand collar. The
wand must be set in the low pressure
(-) position to apply detergents.
Step 3 Fill a container with Kärcher
detergent. Place the filter end of detergent
suction tube into the container.
Step 4 With the engine running, pull
trigger to operate unit: Liquid detergent is
drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
Detergents can only be applied at low pressure (-).
For best results see Cleaning
Tips on pages 8 & 9 for specific
information on how to clean
different surfaces.
Always Use Kärcher
Detergents for Best Results.
Kärcher biodegradable detergents are
specially formulated to protect the
environment and your pressure washer.
The special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a longer
life. For Kärcher Detergents, check your
retailer or call:
The following Kärcher detergents
are available:
• Vehicle Wash • House Wash
• Degreaser • Deck Wash
• All Purpose Cleaner
USA: 1-800-537-4129
www.karcher-usa.com
CAN: 1-800-465-4980
www.karcher.ca
Step 2 Adjust the filter end of the
detergent tube for light (-), or maximum (+)
detergent coverage.
5
USING THE ACCESSORIES
The Vario spray wand allows you to adjust the cleaning pressure. To clean at maximum pressure, the Vario wand must be positioned to the high pressure setting (+). To apply detergent,
the wand must be positioned to the low pressure setting (-).
For high pressure turn
wand collar in the plus
(+) direction.
For low pressure turn
wand collar in the
minus (-) direction.
Warning
TO AVOID SERIOUS INJURY,
NEVER POINT SPRAY NOZZLE AT
YOURSELF, OTHER PERSONS
OR ANIMALS
Vario spray wand
Caution
Never use:
• Bleach, Chlorine products and other
corrosive chemicals
• Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 6
CLEANING TIPS
8
Deck Cleaning
(with or without detergent)
Pre-rinse deck and surrounding area with
fresh water. If using Kärcher Deck Wash,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of approximately 25 square feet. Allow Kärcher Deck
Wash to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. Rinse
at high pressure in a long sweeping motion
keeping the spray nozzle approximately 3-6
inches from the cleaning surface. Always
clean from top to bottom and from left to
right. When moving on to a new section of
the cleaning surface, be sure to overlap the
previous section to eliminate stop marks
and ensure a more even cleaning result.
Caution: Do not use rotating nozzle
spray wand on wood surface as it
may cause damage.
House Siding
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher House Wash, place detergent suction tube directly into cleaning
solution and apply to surface at low pressure (for best results, limit your work area
to sections of approximately 6 feet and
always apply detergent from bottom to top).
Allow Kärcher House Wash to remain on
surface 1-3 minutes. Do not allow detergent
to dry on surface, if surface appears to be
drying, simply wet down surface with fresh
water. If needed, use special Wash Brush
Attachment to remove stubborn dirt. Rinse
at high pressure from top to bottom in an
even sweeping motion keeping the spray
nozzle approximately 6 inches from the
cleaning surface.
Caution: Do not use rotating nozzle spray
wand on siding as it may cause damage.
Cement Patios,
Brick and Stone
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher All Purpose Cleaner, place
detergent suction tube directly into cleaning
solution and apply to surface at low pressure. For best results, limit your work area
to smaller sections of approximately 25
square feet. Allow Kärcher All Purpose
Cleaner to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure in a sweeping
motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and
from left to right. For removing extremely
stubborn stains, use Kärcher Rotating
Nozzle Spray Wand.
Cars, Boats & Motorcycles
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Kärcher Vehicle Wash, place detergent suction tube directly into cleaning solution and
apply to surface at low pressure. For best
results, clean one side of vehicle at a time
and always apply detergent from bottom to
top, do not allow detergent to dry on surface. If needed, use special Wash Brush
Attachment to remove stubborn dirt. Rinse
at high pressure in a sweeping motion
keeping the spray nozzle approximately 6-8
inches from the cleaning surface (distance
should increase when rinsing pin-striping
or other sensitive surfaces). Always clean
from top to bottom and from left to right.
For best results, wipe surface dry with a
chamois or soft dry cloth.
Caution: Do not use rotating nozzle
spray wand on vehicles as it may
cause damage.
7
SHUTTING DOWN & CLEAN-UP
Step 1 Remove
detergent suction tube
from container and insert
into one gallon of fresh
water. Siphon water at low
pressure for one minute.
Step 2
Turn off the
engine.
Step 3
Turn off the water
source.
Step 4
Press trigger to
release water
pressure.
Step 5 Disconnect the
garden hose from the
water inlet on the unit.
Step 6 Disconnect the high pressure hose from the
high pressure outlet and engage the gun safety lock.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
2. Start the machine for a few seconds,
until the water which had remained in the
pump exits. Turn off immediately.
3. Drain the gas and oil from the engine.
4. Do not allow high pressure hose to
become kinked.
5. Store the machine and accessories in
a room which does not reach freezing
temperatures.
Caution: Failure to follow the above directions will result in damage to the pump
assembly and accessories.
TAKING A BREAK... five minutes or more
Step 1 Turn off the
engine.
Step 3 Engage gun
safety lock.
Step 2 Press trigger
to release water pressure.
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 8
TROUBLE SHOOTING
Symptom Cause Solution
No gasoline. Fill gas tank.
Choke is not in correct
position.
Slide choke lever to “CHOKE”
position.
Low oil level. Add oil.
Engine throttle is not in
correct position.
Position the throttle to “FAST”.
Diameter of garden hose is
too small.
Replace with a 3/4 inch garden hose.
Water supply is restricted.
Check garden hose for kinks, leaks
and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in warm
water.
Spray wand is in low
pressure position.
Turn spray wand tip to high pressure
position.
Not enough inlet water supply. Turn w ater on ful l fo rce. Check garden
hose for kinks, leaks or blockage.
Pump is sucking air. Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Water inlet filter is clogged. Remove filter and rinse out in warm
water.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Calcified gun, hose or spray
wand.
Run distilled vinegar through
detergent suction tube.
10
Pressure built up in the
high pressure washer.
Squeeze the trigger to release the
pressure.
Engine will not
start.
Unit does not reach
high pressure.
Output pressure
varies high and low.
For additional
engine problems
refer to the engine
owners manual.
Model K 1800 IB:
Slide the throttle control to the
fast position. Then push primer
ball three times. Wait 3 seconds
between each push.
Note: in cold weather push 5 times.
Model K 1800 IB:
Engine
needs to be primed.
9
CLEANING TIPS
- continued
Barbecue Grills, Outdoor
Power Equipment &
Gardening Tools
(with or without detergent)
Pre-rinse cleaning surface with fresh water. If
using Kärcher All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Kärcher
detergent to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action. To remove
caked on mud from garbage cans, lawn
mower blades, wheel barrels or other
non-sensitive metal surfaces, you may
want to use the Kärcher Rotating Nozzle
Spray Wand.
Caution: Do not use rotating nozzle spray
wand on cloth, plastic or other sensitive
surfaces as it may cause damage.
Patio & Lawn Furniture
(with or without detergent)
Pre-rinse furniture and surrounding area with
fresh water. If using Kärcher All Purpose
Cleaner, place detergent suction tube directly into cleaning solution and apply to surface
at low pressure. Allow Kärcher All Purpose
Cleaner to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface. If
needed use special Wash Brush Attachment
to remove stubborn dirt. Rinse at high pressure in a sweeping motion keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For best results, clean from
top to bottom and from left to right.
Caution: Do not use rotating nozzle spray
wand on patio or lawn furniture as it may
cause damage.
Recommendations
• Before cleaning any surface an inconspicu-
ous area should be cleaned to test spray
pattern and distance for maximum cleaning results.
• If painted surfaces are pealing or chipping,
use extreme caution as pressure washer
may remove the loose paint from the
surface.
OPTIONAL CLEANING ACCESSORIES
Optional cleaning accessories are available to further enhance your cleaning capabilities:
See accessories order form for product descriptions and ordering instructions.
• Rotating Wash Brush
• Wash Brush
• House Washing Wand
• Extension Wand
• Rotating Spray Wand
• Flexible Spray Wand
• Underbody Spray Wand
• Telescopic Spray Wand
• Pipe Drain Cleaner
• Floor Washing Tool
• Sandblasting Attachment
• Detergent Foamer Attachment
• Water Pumping Kit
• Water Suction Hose
• Extension Hose 25’
USA: 1-800-537-4129
www.karcher-usa.com
CAN: 1-800-465-4980
www.karcher.ca
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 10
11
TROUBLE SHOOTING
- continued
If you encounter any additional
difficulties not listed, please call
our service center for help.
Symptom Cause Solution
No detergent.
Garden hose
connection leaks.
Spray wand leaks.
Pump is noisy.
Water leaks from
pump (up to 10
drops per minute
is permissible).
Oil Drip.
Detergent is too thick. Dilute detergent, for best results use
Kärcher detergent.
Filter on detergent suction
tube is clogged.
Run warm water through filter to
remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand is in high
pressure position.
Turn spray wand tip to low pressure
position.
Discharge nozzle is
obstructed.
Blow out or remove debris with a
fine needle.
Loose fitting. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand not properly
attached.
Broken o-ring or plastic
insert.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Loose fittings. Check that all fittings are tight.
Call service center.
Water seals are damaged
or worn.
Thermal protection device will
automatically reset.
Thermal protection device
has been activated.
Call Kärcher customer service
hotline and order repair kit
(part no. 2.883-111.0).
Pump is sucking air.
Oil seals are damaged or
worn.
Call service center.
Insert the spray wand into the trigger
gun. Carefully press in against the
spring tension and twist into the
locked position.
Detergent suction tube not
properly connected to the
machine.
Check connection.
USA: 1-800-537-4129
www.karcher-usa.com
CAN: 1-800-465-4980
www.karcher.ca
K1800IB/2200IB Washer ManV2.2 9/25/02 6:03 PM Page 12
Loading...