www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
2018. 02. 07
Prepared(작성)
Reviewed(검토)
Approved(승인)
Bae wonsik
FMS-HF1
User’ Manual
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 2 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
Revision History
Rev.
date
history
the person in
charge
1.0
2017.11.21
First Release
Bae wonsik
2.0
2018.02.07
Change the list
Bae wonsik
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 3 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
– Contents –
Revision History
1. Synopsis
2. Product Size
3. Specification
4. Postal address
Appendix. Operating method
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 4 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
1. Synopsis
-. It is installed inside the forklift and it manages the information such as vehicle information, driving
record, vehicle condition, workload, driver information from the central server, and on the contrary,
Supports mobile communication network (WCDMA, GSM) and WIFI network for group unit
management system
-. Additional functions include GPS for preventing theft of equipment, RF reader for reading driver
information, and electrostatic touch-type LCD for password input
2. Product Size
Weight
450g
Size
Horizontal
130.7mm
Vertical
132.3mm (Except antenna)
Thickness
53.5mm
3) Certification LABEL location
48
12
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 5 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
3. Specification
3.1. General Specification
1) Rated Voltage: 12/24Vdc
2) Operating Voltage: 9 ~ 32Vdc
3) Operating Temperature: -20℃ ~ +65℃
4) Storage Temperature: -40℃ ~ +85℃
5) Power Consumption: Max. 5W
3.2. 3G Modem(UBLOX / LISA-U200): This device is not supported the voice function.
1) WCDMA
- RMC mode only
- Band 2 & Band 5
2) GSM
- GPRS mode only
- GPRS 850 & 1900
3.3. WIFI
1) TYPE: IEEE 802.11 b/g/n
2) Frequency range: 2 412 MHz ~ 2 472 MHz
3) MODULE: WIS3000XXSR
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 6 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
3.4. GPS
1) TYPE: SMART MODULE
2) GPS receiver With Patch Antenna
3.5. RFID
1) 13.56 MHz [Mifare], ISO 14443 Type A
2) Antenna type: Loop antenna type
3.6. Material of Device: ABS+PC
Substance
Flame Class
Manufacturer
UL File no.
LUPOY GN-5001RF(T)
V-0
LG CHEMICAL
E67171
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 7 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
3.7. PCB Material
PCB
Division
Manufacturer/ Trademark
Layer
/Thickness
Flame
Class
Standard
Mark
UL File
no.
MAIN B/D
JM ELECTRONICS CO
LTD
6layer
/ 1.6T
V-0
UL 796
E117655
POWER
B/D
2layer
/ 1.6T
RFID B/D
2layer
/ 0.4T
3.8. Product label Explanation of graphic symbols used
Symbol
Description
Communaute Europeenne Marking
Federal Communication Commision Marking
Electrical waste and electronics equipment
Direct current
4. Postal address
Kyungwoo Systech, Inc. Office: +82-2-985-8085
#401, Daeryung Post Tower 5, 68, Digital-ro 9, Geumcheon-gu, Seoul, South Korea
E-mail: Webmaster@kyungwoo.com
www.kyungwoo.com
Copyright © 2014 Kyungwoo Systech Inc.
Pages 8 / 8
FMS-HF1 USER’MANUAL
Rev (2.0)
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
To comply with RF exposure compliance requirements, the antenna used for this transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
This device comply with part15 of FCC rules.
Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device & its accessories must accept any interference received, including interference that may cause
undesired operation.
This equipment should be installed and operated with minimum 30 cm between the radiator and your body.
Loading...