Kyosho of America KT 19 User Manual
TRANSMITTER KT-19
产品介绍 Introduction
KT-19 遥控系统主要是用来遥控摩托车模型，通过对发射机进行操作，可以分别
实现相对应的马达驱动及舵机摆动遥控控制；发射机采用 6V/DC 供电，摩托车采用
3.7V 锂聚合物电池进行供电。
KT-19 radio system mainly uses for remote control the motorcycle model.
Through operating transmitter, it can succeed in moving the motor system and the
servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will
be supplied by 3.7V li-poly battery.
产品套装：发射机+摩托车（接收机）+USB 线+充电器+使用说明书。
Product includes: transmitter + motor (receiver)+USB cable + charger + manual
KT-19 遥控系统使用方法及操作步骤
Instruction of KT-19
1. 将发射机与摩托车（接收机）靠近；
1. Keep the transmitter and model closer.
2. 将发射机手轮顺时针拧到底，然后按下电源开关“POWER”，此时发射机 LED 指示
灯会处于闪烁状态；
2. Turning the steering wheel to the end clockwise, and at the same time press the
POWER, then the LED will be flashing.
3. 打开接收机电源开关，接收机 LED 指示灯会长亮 2 秒时间，然后处于闪烁状态，
同时，无刷电机也会发出“滴、滴、滴”的响声；
3. Switch on the power of receiver, then the LED of receiver will be lighting for 2
seconds, after that it will be flashing, and at the same time the brushless motor will
be beeping.
4. 重启发射机电源开关，此时发射机和接收机的 LED 灯都会处于常亮状态，摩托车无
刷电机连续发出 15 声“滴、滴、滴”的响声，然后陀螺马达开始转动;
4. Switch on the transmitter once more, both of the LED of transmitter and receiver
will keep lighting. The brushless motor will keep beeping 15 times after that the
motor of gyro starts to move.
5. 约 5 秒后运转速度达到正常，就可以通过控制发射机的手轮、扣机和陀螺仪的微调，
达到遥控摩托车的方向及车速的目的。
6. The motor will be at the correct speed after 5 seconds. Through operating the trim
of steering wheel, trigger and gyro to adjust the steering and speed of motor.
发射机相关技术参数：
The parameter of transmitter
1. KT-19 发射机工作在 2405.5MHz-2475 MHz 频段内；
1. The frequency of KY-GT2 is between 2405.5MHz to 2475MHz
2. 静态工作电流 17mA 左右；
2. The quiescent current is about 17mA
3. 有效遥控距离 30 米；
3. The range is 30M
4. 符合 CE，FCC 要求；
4. It conforms to the CE and FCC requirement.
5. 发射机重量 280g；
5. The weight of transmitter is 280g
6. 发射机机身长、宽、高：162 x 71 x 295mm。
6. The size of transmitter is 162*71*295mm
摩托车（接收机）体积参数：
Loading...