Gigabit Ethernet Multiplexerr User’s manual www.kyopto.com Gigabit Ethernet Multiplexer User’s manua www.kyopto.com
Gigabit Ethernet Multiplexer
（2×1.25G to 2.5G）3 x SFP
User’s Manual
1．Overview
The Gigabit Ethernet Multiplexer aggregates
2 port Gigabit Ethernet into 1 port 2.5G uplink,
reducing the conversion CAPEX and increasing
the fiber utilization effectively. The multiplexer
can be used either in point-to-point topology
fuctioning as a media converter for transporting
two Gigabit Ethernet services over one fiber or
in CWDM system working as a wavelength
converter for extending the system’s transmitssion capacity doubly. The multiplexer is
equipped with three SFP-based ports: SFP1 is
2.5G uplink port, SFP2 and SFP3 are Gigabit
Ethernet service ports.The multiplexer must be
used in couples.
2. Checklist
Before you installing the Multiplexer, verify
that the package contains the following：
1． The Gigabit Ethernet Multiplexer.
2． AC/DC Power Adapter.
3． This User’s Manual.
Piease notify your sales representative
immediately if any of the aforementioned items
is missing or damaged.
3. LED Description
There are five LED At Front of Multiplexer:
2.5G Lit when SFP1 speed is 2.5Gbps
P1
Lit when SFP1 connection is good.
Blinks when SFP1 data is transmitting.
P2
Lit when SFP2 connection is good.
Blinks when SFP1 data is transmitting.
P3
Lit when SFP3 connection is good.
Blinks when SFP3 data is transmitting.
PWR
Lit when +5V power is coming up.
4. Installing Gigabit Ethernet Multiplexer
The multiplexer must be used in couples.
1. Attach one 2.5G SFP module to SFP1 Cage on the
Multiplexer. Attach two 1.25G SFP modules to
SFP2 and SFP3 Cage on the Multiplexer.
2. Link fiber from the SFP1 on one Multiplexer with
SFP1 on another Multiplexer. It can link through
CWDM system.
3. Link fiber from the SFP2 and SFP3 on the
Multiplexer to Gigabit Ethernet Service.
Note: SFP2 on one Multiplexer link pass only
with SFP2 on another Multiplexer. SFP3 on one
Multiplexer link pass only with SFP3 on another
Multiplexer.
4. Connect the power cord to the Multiplexer and
check that the Power LED lights up. The Px
LEDs will light when all the cable connections
satisfactory.
5. T echnical Specifications
The Multiplexer conforms to the following standards:
z Standerds: IEEE 802.3AB 1000Base-T
1000Base-SX/LX/LH
z Fiber Cable:
Molti-mode: 50/125，62.5/125µm
Single-mode: 9/125µm.
z Data T ransfer Rate:
2.5Gbps for SFP1, 1Gbps for SFP2 and SFP3.
z LED Indicators:
Power, P1 2.5G, P1 Link/Act, P2 Link/Act,
P3 Link/Act,
z Power Requirement: 220V(110-245V)AC，50Hz
z Ambient Temperature: 0 ～ 50℃
z Humidity: 5% ～ 90%
z Dimensions: 26×70×93mm（H×W×D）
6．Typical Application
1. Application 1
Fiber
Multiplexer
Mu ltiplexer
2.5G
2.5G
P1
P1
Gigab it
Eth ernet
Ser vice
Gigab it
Ethernet
Service
Gigabit
Ethernet
Service
Gigab it
Ethernet
Service
P2P2P3P3
1G
1G
1G
1G
2. Application 2
Fiber
2.5G
P3
P3
1G
1G
P1
P2
P1
P2
Muktiplexer1
Mu lt ip lex er 2
Gigabit Ethern et
Service 2
Gigabit Ethernet
Service 3
Gigabit Ethern et
Service 4
Gigabit Ethernet
Service 1
1G
1G
CWDM
Mux/De-mux
CWDM
Mux/De-mux
2.5G
Fiber
Gigabit Ethernet Multiplexerr User’s manual www.kyopto.com Gigabit Ethernet Multiplexer User’s manua www.kyopto.com
Gigabit Ethernet Multiplexer
(2×1.25G to 2.5G)
User’s Manual
Loading...