Kyokuyo Electric KST-1000-W Quick Start Manual

SMART DIGITAL TUNER Worldwide

KST-1000-W
Quick Start Guide

Quick Start Guide

Quick Start Guide

Please keep
this guide
under the tuner.

Connecting to an analog worldwide TV

Recommended connection

pass-through connection

It is recommended that you connect the tuner and your analog TV as shown above.
By this connection, you can watch

- digital TV in regions (countries) where there is terrestrial digital broadcasting
using SMART DIGITAL TUNER.

- analog TV in regions (countries) where there is terrestrial analog broadcasting
using your analog worldwide TV.

1

Disconnect the end

A

of the antenna cable.

Check the shape of the connector

A

Connector type

F type IEC type

2-22-1

2-1

When the connector is F type

A

Connect the end of the antenna cable to the terminal marked “RF-OUT”
of the tuner.

A

Connect as shown below by an antenna cable.

2-2

When the connector is IEC type

A

Disconnect both ends (

and

A B

) of the antenna cable. You do not use this cable.

Prepare two antenna cables. This type of cable is option.

Connect as shown below.

2 pieces

F typeIEC type

Male Male

3

Connect as shown below. You can use an HDMI cable or an Audio/Video cable.
You can watch the highest quality of the picture with an HDMI cable.

＊

Do not use both an HDMI cable and an Audio/Video cable together.

4

Connect to an AC adapter.

If you do not have an analog worldwide TV, connect the tuner to a TV or a monitor
as shown below. You cannot watch the analog TV by this connection.

TV or Monitor

Continued overleaf

5

Turn on the TV and select the appropriate video input on the TV.
And then, turn on the tuner.

Channel Scan

1.

Check whether terrestrial digital broadcasting has been started
in the region (country) where the tuner will be used.
If you do not know whether it has been started or not,
scan terrestrial analog broadcasting channels using your
analog worldwide TV. (Set up a pass-through connection)

2.

If some channels are detected by your analog worldwide TV,
enjoy watching analog TV programs.

3.

If digital broadcasting has been started in the region (country)
where the tuner will be used or if not even one channel was
detected as a result of channel scan by your analog worldwide TV,
proceed to next step.

Region selection and channel scan

Region selection and channel scan are performed using the Scan button
on the remote control, or from "Region/Channel scan" on the Menu screen.
Select "Region/Channel scan" on the Menu screen, and press the OK button.

Scan button
or
Press Menu to display
the Menu screen.

Select with ▲▼,

and press OK.

1. Select the current region (broadcasting standard) from the screen,
and press the OK button. Channel scan will start automatically.

Select with ▲▼, and
press OK.

ISDB-T Japan
ISDB-TB South America, etc.
DVB-T/T2 EU, Russia, Australia, Taiwan, Singapore, UAE, etc.
ATSC North America, Korea, etc.
DTMB China, Hong Kong, etc.

As of March 2015

2. When channel scan is finished, a list of detected channels is displayed.
Select "OK" and press the OK button. The TV image will be displayed.

Select with ▼, and
press OK.

If not even one channel was detected as a result of channel scan or if you
do not know which broadcast standard is used at the current location,
select "All Scan" once on the region selection screen, and press OK.
"All Scan" scans all broadcasting standards in order, so it may take
about 30 minutes.

Select with ▲▼, and
press OK.

The possible reasons why it was impossible to detect the channel are
described on the Operating Instructions P.18.

*

Rescan same region Convenient method of use

When the location has been moved, within the same broadcasting standard,
you can also use "Rescan same region" from the immediately preceding
TV viewing time.
Examples: When you have moved within the same country,
or with the European (DVB-T/T2) region.

Select with , and
press OK.

▲

▲

Important Precautions for viewing terrestrial broadcasting

1.

Check whether terrestrial digital broadcasting has been started
in the region (country) where the tuner will be used.

This product has a receiver for terrestrial digital broadcasts, and does not
allow TV viewing in regions (countries) where there is no terrestrial digital
broadcasting. In addition, it cannot receive terrestrial analog broadcasts.
However, if terrestrial digital broadcasting is not provided in the area
where the tuner is used, there is a possibility that analog TV is provided.
If you have an analog TV, set up a pass-through connection (on the back
of this page) between this product and analog TV, and try viewing with the
analog TV.

Even in countries where terrestrial digital TV broadcasting has been started,
it may be impossible to view digital TV if the current location (anchor point)
is distant from the broadcasting station, or if it is impossible to obtain signal
strength sufficient for TV viewing at unfavorable locations such as those
where noise has an effect on TV signals.

2.

Standards for terrestrial digital broadcasting are not uniform
throughout the world, and thus before searching for channels
which can be viewed (channel scan),it is necessary to specify
the broadcast standard for channel scanning.

If channel scan is performed with a different broadcast standard,
channels will not be detected.

*

Broadcasting standards are established by regions (countries). With this
product, it is possible to perform channel scan with either of the following:

Scanning by designating a region (country) or broadcasting standard
Sequential scanning of all broadcasting standards

With "All Scan", all broadcasting standards are scanned in sequence,
and this takes time.
Therefore, if the broadcasting standard at the current location or geographical
point is known, it is recommended to perform channel scan with method .

A

A

B

B

2015.05v1