KYOKUTOH KIKK, KIKK-EL Teaching Manual Instruction Manual

（

）

First edition, June 28, 2019.

KIKK Teaching Guide Instruction Manual

for Auto Tip Changer

Please read this instruction manual carefully and use it correctly before using it.

TT-ATC-**

※KIKK is sold separately.

1. Precautions

2. Suitability Mode

3. How to use

Contacts

Content

2

3

4

10

1

1. Precautions

※

Be careful to follow directions as specified, as an error could lead to

Be careful to follow direction as specified, as an error could lead to

This product is different from the suitable product by the shape of the
cap tip.
If you work with a improper teaching guide,
It cannot be performed.
Please carry out the work after you check the suitability.

■ Precautions

The teaching guide for KIKK auto tip changer is used to in our manufacturing tip changer,

that it is easy to carry out teaching of robot gun.

This product reduces errors caused by teaching precision, and ensures proper

performance of the remover and normal operation of the facility.

This product supports the teaching of the tip changer. It cannot be used for any other

purpose. Also, it cannot be used for the tip changer other than the specified type.
①Use other than specified model ②Use other than correct purpose ③ Use other than

correct purpose

We cannot hold responsible for any failures, repairs, accidents, or other errors that

occurred in the event of carrying out above 3 items, so please understand it in advance.

■ Symbol

possible injury or death.

malfunction and serious damage.

■ Usage Precautions

 Do not perform the remove operation during use of the teaching guide to prevent

damage to the tip changer.

This symbol indicates operations that should not be done.

This symbol indicates operation that should be done.

 Be sure to remove the teaching guide after confirming the middle of the gun and

the tip changer.

If a re-move operation is carried out with the teaching guide installed, there is a

risk of damage to the tip changer.

2

2. Suitability Mode

■Line up

The matching list of this product is as follows:

3

3. How to use

＜

■ Precautions before using

・Cap tip must be equipped with new products and operate.
・Check whether the robot is horizontal or vertical.
・Check the suitability for shape of cap tip and teaching guides.
・When operating a robot, make sure that there is no danger around it.

1. Upper Teaching＞

■ Work Order

1. Check if the tip changer groove is containment.

2. Install the teaching guide.

※Check if it is mounted slopingly.
※There is no upper or lower part of the product.

4

3. Close the gun to the teaching guide.

4. Adjust horizontal and vertical and move directly on the center of the teaching guide.

5

5. Finely adjust and insert the cap tip into the teaching guide about 10mm.

If it is inserted correctly, horizontal and vertical are adjusted.

Make sure that the cap tip do not reach to the bottom.

If it is continued to insert into the bottom, it may damage the product.

Cross section

6. After inserting the cap tip into the center, and retreat it in the upward direction of the

Z-direction.

6

7. After retreating, remove the teaching guide.

8. Insert the cap tip back into the center of the groove of remover, adjust the cap tip

surface to parallel with the remover face

※Make sure that the two red sides of the picture on the right are parallel.

◆ As shown in the picture on the right

above, the center of the cap tip and

the groove are adjusted as the cross

-sectional view, if adjust aligning

the cap tip surface with the remover

Cross section

face.

9. When adjustment is complete and position is registered, the top teaching is complete.

7

＜

2. Bottom teaching＞

■ Work order

1. After finishing the top teaching, retract the gun to work on the bottom.

2. Check if the grooves are containment in the same way as above.

3. Install the teaching guide.

8

4. Finely adjust and insert the cap tip into the teaching guide about 10mm.

※

If it is inserted correctly, horizontal and vertical are adjusted.

5. If it is inserted to the center, remove the teaching guide as above,

Insert the cap tip again to parallel the surface of cap tip and remover.

6. When you register position, the bottom teaching is completed.

Completed

For teaching other than the remover section, please refer to the

[teaching page] in the KIKK instruction manual.

9

Contacts

TEL [phone] FAX [phone]

Contact us if there is any damage or machine defects in our products.

KYOKUTOH CO., LTD

181-1, Nakayashiki, Orido-cho, Nisshin, Aichi 470-0115 Japan

TEL [phone] FAX [phone]

E-Mail: [e-mail]

http://www.kyokutoh.com

KANTO SALES OFFICE

TEL [phone] FAX [phone]

HIROSHIMA SALES OFFICE

CHANGER ＆ DRESSER CORPORATION

1527 ITC Way, Anniston, AL 36207 U.S.A
TEL [phone] FAX [phone]
http://www.changer-dresser.com

KYOKUTOH CHINA

73 Huagang Street, Xiuquan Town, Huadu District,
GuangZhou City, GuangDong Province, China.
TEL [phone] FAX [phone]
http://www.kyokutoh.com.cn

KYOKUTOH THAILAND

339/2 Soi Phattanakarn 69, Phattanakarn Road, Prawet,
Bangkok 10250 THAILAND
TEL [phone] FAX [phone]

KYOKUTOH KOREA

117, Tawon TAKRA II Industry Center, Dongsan-ro 76,
Danwon-gu, Ansan-si, Gyeonggi-do, Korea 15434
TEL [phone] FAX [phone]

KYOKUTOH EUROPE

Radlkoferstr. 2 81373 Muenchen, Germany
TEL [phone] FAX [phone]

10