Kyocera IUU19AC Users Manual

iBurst Terminal USB Model (UTU) Manual

Octo

ber

28, 200

8 Date:

1.00 Revision:

S40T-EE-005 Reference:

For Windows Vista/XP

Designed

Uetani Yamamoto

- 1 -

Approved

Koyama

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

Checked

Revision History

Revision

1.00 Uetani Oct 28, 2008 First Edition

Author Date Detail

iBurst Terminal USB Model (UTU) Manual

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 2 -

iBurst Terminal USB Model (UTU) Manual

CONTENTS

CONTENTS CONTENTS

Safety Precautions on iBurst Terminal

Safety Precautions on iBurst Terminal ................................

Safety Precautions on iBurst TerminalSafety Precautions on iBurst Terminal Chapter 1

Chapter 1 Introduction

Chapter 1Chapter 1

Components List

Components List................................

Components ListComponents List Requirements on your PC

Requirements on your PC ................................

Requirements on your PCRequirements on your PC Outlook of iBurst Terminal

Outlook of iBurst Terminal ................................

Outlook of iBurst TerminalOutlook of iBurst Terminal Indicators

Indicators................................

IndicatorsIndicators Outlook to use the iBurst Terminal

Outlook to use the iBurst Terminal................................

Outlook to use the iBurst TerminalOutlook to use the iBurst Terminal

Chapter 2

Chapter 2 Setup Procedure

Chapter 2Chapter 2

Installation for Window

Installation for Windows Vista/XP

Installation for WindowInstallation for Window Connection Settings for Windows Vista

Connection Settings for Windows Vista ............................................................................................ 14

Connection Settings for Windows VistaConnection Settings for Windows Vista

Creating a connection and starting the connection

Creating a connection and starting the connection ................................

Creating a connection and starting the connectionCreating a connection and starting the connection To disconnect

To disconnect ................................

To disconnectTo disconnect To connect again

To connect again ................................

To connect againTo connect again Tips for useful connection settings

Tips for useful connection settings ................................

Tips for useful connection settingsTips for useful connection settings

Connection Settings for Windows XP

Connection Settings for Windows XP ................................................................................................ 22

Connection Settings for Windows XPConnection Settings for Windows XP

Creating a connection

Creating a connection................................

Creating a connectionCreating a connection To connec

To connectttt ................................

To connecTo connec To disconnect

To disconnect ................................

To disconnectTo disconnect Tips for useful connection settings

Tips for useful connection settings ................................

Tips for useful connection settingsTips for useful connection settings

Cha

Chapter 3

pter 3 Utility Software

ChaCha

pter 3pter 3

Introduction ................................

IntroductionIntroduction

................................................................

Setup Procedure................................

Setup ProcedureSetup Procedure

................................................................

Utility Software ................................

Utility SoftwareUtility Software

................................................................

s Vista/XP..................................................................................................... 10

s Vista/XPs Vista/XP

................................................................

...........................................................

................................................................

.....................................................

................................................................

............................................................

................................................................

...................................................

................................................................

.......................................

................................................................

........................... 6666

......................................................

.....................................

................................................................

........................................................

................................................................

......................................................

................................................................

...............................................

................................................................

...........................................

................................................................

...................................................

................................................................

........................................

................................................................

...................................

................................................................

..........................................

................................................................

............................................

................................................................

........................................

................................................................

..........................................

................................................................

........................7777

................................................

......................7777

............................................

..................... 9999

..........................................

................... 14

......................................

............................ 22

........................................................

................... 30

......................................

....... 4444

..............

.....7777

..........

...............8888

..............................

...........8888

......................

........ 17

................

... 18

......

.......... 20

....................

............ 26

........................

........ 27

................

.......... 28

....................

14

1414 17

1717 18

1818 20

2020

22

2222 26

2626 27

2727 28

2828

30

3030

Utility Software on Windows

Utility Software on Windows.............................................................................................................. 31

Utility Software on WindowsUtility Software on Windows

Chapter 4

Chapter 4 Uninstallation

Chapter 4Chapter 4

Uninstallation for Windows Vista

Uninstallation for Windows Vista...................................................................................................... 38

Uninstallation for Windows VistaUninstallation for Windows Vista Uninstallation for Windows XP

Uninstallation for Windows XP.......................................................................................................... 41

Uninstallation for Windows XPUninstallation for Windows XP

Appendix

Appendix ................................

AppendixAppendix

Utility software will be not uninstalled when back

Utility software will be not uninstalled when back----to

Utility software will be not uninstalled when backUtility software will be not uninstalled when back Trouble when disabling a built

Trouble when disabling a built----in wireless LAN device on Windows PC

Trouble when disabling a builtTrouble when disabling a built FCC Compliance Statement

FCC Compliance Statement............................................................................................................... 45

FCC Compliance StatementFCC Compliance Statement FCC RF Radiation Exposure Statement

FCC RF Radiation Exposure Statement........................................................................................... 46

FCC RF Radiation Exposure StatementFCC RF Radiation Exposure Statement

Uninstallation................................

UninstallationUninstallation

................................................................

in wireless LAN device on Windows PC ....................................... 45

in wireless LAN device on Windows PCin wireless LAN device on Windows PC

......................................................

................................................................

to----date on Windows Vista

date on Windows Vista ............................. 45

toto

date on Windows Vistadate on Windows Vista

...................... 37

............................................

..................................................

................................................................

.................. 44

....................................

37

3737

44

4444

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 3 -

iBurst Terminal USB Model (UTU) Manual

Safety Precautions on iBurst T

Safety Precautions on iBurst Terminal

Safety Precautions on iBurst TSafety Precautions on iBurst T

erminal

erminalerminal

• Things you must know

• When using the product, use it correctly according to the safety precautions.

• The product uses particular radio frequency band tuned for the network operator.

• The safety precautions, hardware, software, and the design of the product may be changed

in the future without any announcement to the customers.

• About use restriction

• The product is designed as an OA apparatus for home use. Please use it neither in the

medical apparatus directly to affect a human life, nor the system of which very high reliability is required.

• Do not use the product in the zone where the wireless machines are forbidden, such as an airplane and a hospital. An electric device and medical apparatus are affected and it becomes the cause of the accident.

• About Qualification

• Our company does not take any responsibility about the damage produced by use under

the conditions such as natural disasters, earthquake, flood, fires, misuse by intent or carelessness or other than the responsibility of our company.

• Our company does not take any responsibility about the damage produced by external factor, failure, malfunction, and fault of product, such as loss of enterprise profits, enterprise discontinuation, change and disappearance of the contents of memory etc.

• Our company takes no responsibility about the damage produced by not keeping the written contents of an owner's manual.

• Our company takes no responsibility about the damage produced from incorrect operation in combination with the connection apparatus and software in which our company is not participating etc.

• iBurst ™ is a registered trademark of ArrayComm, Inc.

• Windows and Windows Vista are registered trademarks of Microsoft Corporation.

• Mac OS X is a registered trademark of Apple Inc.

• In addition, the name of the software carried in this document and peripheral equipment is

each company’s trademark, or a registered trademark.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 4 -

iBurst Terminal USB Model (UTU) Manual

• For your safety

-------- Danger

( If used improperly, may cause death or serious injury. )

• Do not use with an abnormal condition, such as with emission of smoke or odor. It may

• Do not disassemble or remodel the product. It may cause fire or electrical shock.

• Do not use or place the product at places with high humidity such as in the bath room or

------- Warning

• Do not give a shock strong against the product, such as dropping and throwing. It becomes

• Do not put the product under direct sunshine or near equipment with high temperature

• Do not put the product at places with an extreme fluctuation of temperature, such as near

• Do not put the product at places with oil and steams such as in the kitchen. In addition, do

• Do not place the product on unstable places such as on an unsteady desk or slanted

• When the thunder occurs in near, do not use the product and its peripheral equipment. It

• Do not touch the connector pins directly with your hands. Static electricity may affect the

• Do not use it in the intense place of vibration. It becomes the cause of failure.

Danger --------

Danger Danger

cause fire or electric shock.

near the humidifier. It may cause fire or electric shock. And do not touch the product with wet hands.

Warning --------

Warning Warning

( If used improperly, may cause disability or physical damage. )

the cause of failure. Moreover, do not ride on the product. It may become the cause of an injury.

such as a stove and a heater. It may raise the temperature of the interior and cause fire.

the air conditioner or a heater. The dew condensation may occur in the interior and cause fire, electrical shock, and malfunction.

not put it at dusty places and places where metal powder and toxic gas occur. It may cause fire or electric shock.

surfaces. In addition, do not put any object on the product. It may loose balance and tumble, or fall and cause injury.

may become the cause of an electric shock.

components. As static electricity is created from both the cloth and the human body, before putting or removing the product, release static electricity by touching a metal object such as a small cabinet.

--------

----------------

--------

----------------

-------- Caution

• Do not put the product at low temperature. The product may not function properly.

• Do not put the product on the top of magnetic objects and places where electromagnetic

• The product lifetime may shorten if used at places with hydrogen sulfide such as at a hot

• Data communication will be disabled or a data file may corrupt if the PC is turned off or

• When connecting the product onto PC via USB cable, use the enclosed USB cable.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

Caution --------

CautionCaution

( If treated improperly, the equipment may not perform or work properly. )

waves occur. This includes electrical appliances, AV, and OA (microwave oven, speaker, TV, radio, fluorescent light, inverter air conditioner, and electric kitchen appliances). The product will not be able to make communication properly if effected by magnetism or electronic noise. Putting the product near TV or radio may cause RF receive error.

spring.

the product is separated from the PC during the communication. Important data must be verified against the original data.

- 5 -

Chapter 1

Chapter 1 Introduction

Chapter 1Chapter 1

Introduction

IntroductionIntroduction

This chapter

This chapter describ

This chapter This chapter using iBurst

using iBurst Terminal

using iBurst using iBurst

iBurst Terminal USB Model (UTU) Manual

describes what should be confirmed

describdescrib

Terminal....

TerminalTerminal

es what should be confirmed before

es what should be confirmed es what should be confirmed

before

before before

7

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 6 -

iBurst Terminal USB Model (UTU) Manual

USB

connector

Link/Communication Indicator

Antenna

Components List

Components List Components List The table below shows the list of components. Please confirm items in the package.

USB model

Component

Component Notes

ComponentComponent

iBurst Terminal Unit of USB model

*Refer to the picture shown below.

USB Extension Cable Type: USB1.1

Length: 1m

Holder *Refer to the picture shown below 1

Requirements on your PC

Requirements on your PC Requirements on your PC

Notes Q’

NotesNotes

Q’ty

Q’Q’

1

ty

tyty

• PC/AT Compatible PC with Windows Vista/XP (x86 based); or

version 10.4 to 10.5 of Mac OS X. (Refer to the manual for Mac OS X.)

• 1 USB1.1 port or a later version of USB port.

Outlook of iBurst Terminal

Outlook of iBurst Terminal Outlook of iBurst Terminal

USB model

Holder

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 7 -

iBurst Terminal USB Model (UTU) Manual

USB Cable

UTU

Indicator

Indicators

IndicatorIndicator

s

s s

The table below describes meaning of each indicator.

Indicator State Meaning

Link/Communication Indicator OFF Turned OFF Amber No signal receiving Yellow Weak signal receiving

Flashing when communicating.

Green Strong signal receiving

Flashing when communicating.

Amber/Yellow Fault (Flashing)

Outlook to use the iBurst Terminal

Outlook to use the iBurst Terminal Outlook to use the iBurst Terminal A USB model shall be connected to a USB port of your PC directly or via USB cable. Before

connecting the USB interface, you have to install iBurst software which includes device drivers.

Please read through every sections related with the operating system for details.

USB Connection

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 8 -

Chap

Chapter 2

ChapChap

ter 2 Setup Procedure

ter 2ter 2

Setup Procedure

Setup ProcedureSetup Procedure

iBurst Terminal USB Model (UTU) Manual

This chapter describes how to install

This chapter describes how to install iBurst software,

This chapter describes how to install This chapter describes how to install

guides you how to make a network connection so as to use

guides you how to make a network connection so as to use guides you how to make a network connection so as to use

data communication service.

data communication service.data communication service.

iBurst software, then

iBurst software,iBurst software,

then

then then

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 9 -

iBurst Terminal USB Model (UTU) Manual

Installation

Installation for

Installation Installation

This section shows the procedure to install iBurst software on your PC for utilizing iBurst

Terminal. The procedure shall be done once before using it.

for Windows Vista/XP

Windows Vista/XP

forfor

Windows Vista/XP Windows Vista/XP

ATTENTION: If you have installed an old version of iBurst software or you updated Windows

version, you have to uninstall the existing iBurst software first. Otherwise

performance and/or throughput through iBurst Terminal may be restricted.

NOTE: All screen copies in this section are examples on Windows Vista.

1. Make sure to remove the iBurst Terminal from your PC. ATTENTION: Don

2. Turn your PC on.

3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or

execute the appropriate installation software.

4. On Windows Vista, click [Allow] to proceed installing when Windows prompts [User Account

Control].

Don’’’’t

t plug

plug the iBurst Terminal

DonDon

the iBurst Terminal into

t t

plugplug

the iBurst Terminal the iBurst Terminal

into your PC until completion of installation.

your PC until completion of installation.

intointo

your PC until completion of installation. your PC until completion of installation.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 10 -

5. The software will show progress of preparation.

6. iBurst Terminal Setup starts. Click the [Next >] button.

iBurst Terminal USB Model (UTU) Manual

7. Read through the license agreement. If you can agree it, select [I accept the terms the license

agreement] and click the [Next >] button.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 11 -

iBurst Terminal USB Model (UTU) Manual

8. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder.

9. Click the [Next >] button.

10. The following dialog window will appear, and installation of software begins.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 12 -

iBurst Terminal USB Model (UTU) Manual

The iBurst icon will

ed when a UT

11. When the installing process finishes, the dialog window shown below will appear. Select [Yes, I

want to restart my computer now] and click the [Finish] button in the dialog window.

NOTE: Before restarting the PC, you can find an iBurst icon on the task tray.

12. After finish of restarting, plug the iBurst Terminal into an appropriate port. The iBurst

Terminal will be recognized and will be ready to use automatically. Only when the iBurst

Terminal is plugged into every port at the first time, you will see installation status on balloon

messages as follows.

NOTE: The pictures below are examples on Windows Vista.

A balloon message when Windows detects the iBurst Terminal as a new hardware.

A balloon message when Windows finishes installation of the iBurst Terminal.

be vari recognized

13. To connect to the Internet, jump to the page listed below depending on Windows version.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

Windows Vista  page 14

Windows XP  page 22

- 13 -

Connection

Connection Settings

Connection Connection

Creating a connection and

Creating a connection and starting the connection

Creating a connection andCreating a connection and

1. Make sure to plug the iBurst Terminal into your PC.

Settings for Windows Vista

SettingsSettings

for Windows Vista

for Windows Vista for Windows Vista

starting the connection

starting the connection starting the connection

iBurst Terminal USB Model (UTU) Manual

2. Click the [Start] button and click [Connect To] as shown below; or

Right click on the network icon at the task tray and select [Connect to a network].

or

oror

3. Click [Set up a connection or network] in the [Connect to a network] display.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 14 -

4. Select [Connect to the Internet] and click the [Next] button.

5. Select [Broadband (PPPoE)].

iBurst Terminal USB Model (UTU) Manual

6. Enter user name and password assigned by the internet service provider (ISP) you subscribed.

It is recommended to enable [Remember this password]. Any connection name is acceptable

but this manual uses [iBurst] as an example of a connection name. It is not recommended to

enable [Allow other people to use this connection]. And then, click the [Connect] button.

Enabling it is recommended.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 15 -

iBurst Terminal USB Model (UTU) Manual

7. The dialog shows [Connecting to <the connection name>…] in several seconds.

8. After connected, the dialog shows [Testing your Internet connection…] in several seconds.

9. When the dialog shows [You are connected to the Internet], click [Close] button. Of course you

may choose [Browsing Internet] to open the Internet Explorer.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 16 -

iBurst Terminal USB Model (UTU) Manual

10. When the dialog shows [Set a location for the ‘<the connection name>’ network], click [Cancel]

button. Of course you may choose a location among them.

To disconnect

To disconnect To disconnect

1. Right click on the network icon at the task tray, select [Disconnect from] and click the

appropriate connection name.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 17 -

iBurst Terminal USB Model (UTU) Manual

To connect

To connect again

To connectTo connect

This section shows the procedure to connect to the Internet again through iBurst. You have to do

this every time before starting Internet accessing.

1. Click [Start] button and click [Connect To]; or

again

again again

Right click on the network icon at the task tray and select [Connect to a network].

2. Choose the connection name for iBurst service and click [Connect].

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 18 -

iBurst Terminal USB Model (UTU) Manual

3. When a dial-up connection dialog is popped up, fill items and click [Connect].

4. When connected successfully, click [Close].

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 19 -

iBurst Terminal USB Model (UTU) Manual

Tips for useful connection settings

Tips for useful connection settings Tips for useful connection settings

When you open Internet Explorer, Windows Vista will attempt to make the Internet connectivity

according to a particular setting in the Internet Explorer if not connected. The tips below will

give you useful information.

1. When the dial-up connection dialog for iBurst service as shown below appears, it is

recommended to enable [Connect automatically]. This will make Windows Vista to connect to

the Internet without any your key action when Windows Vista needs the Internet connectivity.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 20 -

iBurst Terminal USB Model (UTU) Manual

Selecting

“

Always dial ...

”

The connection name of

2. You can enable always connection on the [Internet Properties] as follows. In order to open the

dialog, open the Internet Explorer, select [Tools] -> [Internet Options]. You can find the

setting on [Connections] tab of the dialog.

iBurst service must be the default connection.

is recommended

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 21 -

iBurst Terminal USB Model (UTU) Manual

Connection

Connection Settings

Connection Connection

Creating a connection

Creating a connection Creating a connection

1. Make sure to plug the iBurst Terminal into your PC.

2. Click the [Start] button, and click [Control Panel] as shown below.

Settings for Windows XP

SettingsSettings

for Windows XP

for Windows XP for Windows XP

3. Click [Network and Internet Connections] in the [Control Panel] display.

4. Click [Set up or Change your Internet connection].

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 22 -

iBurst Terminal USB Model (UTU) Manual

5. When the [Internet Properties] dialog window appears, click the [Setup] button.

6. [New Connection Wizard] will begin and the dialog window as shown below will appear.

Click the [Next >] button in the dialog window.

7. Select [Connect to the Internet] and click the [Next >] button.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 23 -

iBurst Terminal USB Model (UTU) Manual

8. Select [Set up my connection manually] and click the [Next >] button.

9. Select [Connect using a broadband connection that requires a user name and password] and

click the [Next >] button.

10. Fill in [ISP Name]. Any ISP name is acceptable. And then, click [Next >] button.

NOTE: “iBurst” in the picture below is an example.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 24 -

iBurst Terminal USB Model (UTU) Manual

11. Enter user name and password and make sure that the [Make this the default Internet

connection] check box is checked. Click the [Next >] button.

Check it if you want.

Nothing in case SP2 and SP3 of Windows XP.

12. Click the [Finish] button.

Check it if you want.

13. Close [Network and Internet Connection] window.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 25 -

iBurst Terminal USB Model (UTU) Manual

iBurst

To connect

To connect To connect

This section shows the procedure to connect to the Internet through iBurst. You have to do this

every time before starting Internet accessing.

1. Click [Start] button, [Connect To] and <Connection name you created>.

NOTE: The connection name “iBurst” in the picture below is an example.

2. When a dial-up connection dialog is popped up, fill items and click [Connect].

3. When the connection establishment process is complete, a message indicating completion of the

connection will appear at the task tray as shown below.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 26 -

iBurst Terminal USB Model (UTU) Manual

To disconnect

To disconnect To disconnect

1. Click [Start] button, [Connect To] and <Connection name you created>.

NOTE: The connection name “iBurst” in the picture below is an example.

2. When a connection status dialog is popped up, click [Disconnect].

3. It will be disconnected.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 27 -

iBurst Terminal USB Model (UTU) Manual

The ISP name specified when

Tips for useful connection settings

Tips for useful connection settings Tips for useful connection settings

1. You can enable always connection on the [Internet Properties] as follows. In order to open the

dialog, open the Internet Explorer, select [Tools] -> [Internet Options]. You can find the

setting on [Connections] tab of the dialog.

2. When the [Internet Options] dialog window appears, select [Connections] tab. Confirm the

connection name, select [Always dial my default connection], and then click [OK].

creating a connection must be the default connection.

Select “Always dial ...”.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 28 -

iBurst Terminal USB Model (UTU) Manual

the Internet.

3. When you open Internet Explorer, the [Dial-up Connection] dialog as shown below will appear.

Click the [Connect] button to connect to the network.

NOTE:

If you don’t choose “Always dial my default connection” at step 2 above, you have to open this dial-up connection dialog manually every when you want to connect to

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 29 -

Chapter 3

Chapter 3 Utility Software

Chapter 3Chapter 3

Utility Software

Utility SoftwareUtility Software

iBurst Terminal USB Model (UTU) Manual

This chapter describes the features and usage of the

This chapter describes the features and usage of the This chapter describes the features and usage of the

Utility Software

Utility Software for iBurst Terminal.

Utility Software Utility Software

for iBurst Terminal.

for iBurst Terminal.for iBurst Terminal.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 30 -

iBurst Terminal USB Model (UTU) Manual

Utility Software on Windows

Utility Software on Windows Utility Software on Windows

To open the utility dialog.

1. To open the utility dialog, double click the icon on the computer’s task tray; or

click [Start] -> [All Programs] -> [iBurst Terminal] -> [iBurst_Terminal UTL]. When the

dialog opens, the [Link Info] pane will be displayed as shown below.

2. To close the utility dialog window, click the [OK] button, the [Cancel] button or the ‘X’ button at

upper-right corner of the dialog window.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 31 -

iBurst Terminal USB Model (UTU) Manual

Link Info Pane

[Link Info] pane indicates several communication statuses about iBurst Terminal.

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

The following descriptions are about each item on the pane.

(1) UTID

UTID

UTIDUTID

UTID is an identifier assigned to the iBurst Terminal. This will be used for maintenance

support.

(2) Link Status

Link Status

Link StatusLink Status

This indicates current link status between the iBurst Terminal and the access point.

Connect :

Connect : The link is connected.

Connect :Connect : No Connect

No Connect : The iBurst Terminal is connected with your PC but the link is not

No Connect No Connect

connected.

No iBurst_Terminal :

No iBurst_Terminal : There is no iBurst Terminal connected with your PC.

No iBurst_Terminal :No iBurst_Terminal :

(3) Link Speed

Link Speed

Link SpeedLink Speed

This indicates current bandwidth allocated automatically between the iBurst Terminal

and a radio base station.

(4) Frame Error Rate

Frame Error Rate

Frame Error RateFrame Error Rate

This indicates current Frame Error Rate on the downlink air.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 32 -

(5) Signal Strength

Signal Strength

Signal StrengthSignal Strength

This indicates current signal strength of the received radio signal. The signal bar

indicates the level visually in percentage and the status words are categorized according

to the percent level as follows.

No Signal :

No Signal : 0%

No Signal :No Signal : Poor :

Poor : In the range of 1 to 24%

Poor :Poor : Fair :

Fair : In the range of 25 to 49%

Fair :Fair : Good

Good : In the range of 50 to 74%

GoodGood Excellent :

Excellent : In the range of 75 to 100%

Excellent :Excellent :

(6) Current Data Rate

Current Data Rate

Current Data RateCurrent Data Rate

This indicates current throughputs on both directions.

(7) Total Byte Received

Total Byte Received

Total Byte ReceivedTotal Byte Received

Total Byte Received indicates the total number of bytes received from the access point

iBurst Terminal USB Model (UTU) Manual

since the communication link is established.

(8) Total Byte Sent

Total Byte Sent

Total Byte SentTotal Byte Sent

Total Byte Sent indicates the total number of bytes transmitted to the access point since

the communication link is established.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 33 -

iBurst Terminal USB Model (UTU) Manual

Setup Pane

[Setup] pane can be displayed in the main dialog window by clicking the [Setup] tab. This pane

controls enabling/disabling to show each indicator on the [Link Info] pane.

(1)

(2)

(3)

(4)

(5)

The following descriptions are about each item on the pane.

(1) Selecting [ON] enables the corresponding indicator on the Link Info pane.

All are [ON] as the default.

(2) Selecting [OFF] disables the corresponding indicator on the Link Info pane.

(3) [Apply] button activates every setting above.

(4) [Reset] button enables and activates all settings above.

(6)

(5) [OK] button activates every setting above and close the dialog.

(6) [Cancel] button closes the dialog without activation of the settings.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 34 -

About Pane

iBurst Terminal USB Model (UTU) Manual

[About] pane shows the version information about software, hardware and copyrights.

(1)

(2)

(3)

The following descriptions are about each item on the pane.

(1) This shows the version number and the build date of this Utility Software.

(2) This shows the firmware version and the build date of it.

(3) This shows the hardware version and the manufactured date of the iBurst Terminal.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 35 -

iBurst Terminal USB Model (UTU) Manual

Icon Display in task tray

When the Utility Software for iBurst Terminal is running, an icon of the Utility Software will be

displayed in the task tray of the computer monitor according to communication status of the iBurst

Terminal.

The table below shows icons with status descriptions.

Icon

Icon Statu

IconIcon

Status of iBurst Terminal

s of iBurst Terminal

StatuStatu

s of iBurst Terminals of iBurst Terminal

iBurst Terminal is not plugged into your PC.

There is no transmission nor reception on iBurst Terminal.

iBurst Terminal is transmitting data.

iBurst Terminal is receiving data.

iBurst Terminal is both transmitting and receiving data.

Link Status, Total Byte Received,

Pointing on the iBurst icon on the task tray, a balloon indicates

Total Byte Sent

Total Byte Sent and Signal Strength

Total Byte Sent Total Byte Sent pane.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

Signal Strength as shown below, but depending on the settings on the [Setup]

Signal Strength Signal Strength

Link Status, Total Byte Received,

Link Status, Total Byte Received, Link Status, Total Byte Received,

- 36 -

Chapter 4

Chapter 4 Uninstallation

Chapter 4Chapter 4

Uninstallation

UninstallationUninstallation

This chapter describes how to uninstall

This chapter describes how to uninstall iBurst software

This chapter describes how to uninstall This chapter describes how to uninstall

iBurst Terminal USB Model (UTU) Manual

iBurst software....

iBurst softwareiBurst software

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 37 -

iBurst Terminal USB Model (UTU) Manual

Uninstallation for Windows

Uninstallation for Windows Vista

Uninstallation for Windows Uninstallation for Windows

1. Close all programs currently running.

2. Remove the iBurst Terminal from your PC.

3. Click [Start] -> [Control Panel] to open the Control Panel, and then click [Uninstall a program]

beside the [Programs] icon.

Vista

Vista Vista

4. Select [iBurst Terminal] software, and click the [Uninstall] button.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 38 -

iBurst Terminal USB Model (UTU) Manual

5. When Windows prompts [User Account Control], click [Continue] to proceed uninstalling.

6. The software will show progress of preparation.

7. Click the [OK] button after appearing dialog window as shown below.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 39 -

iBurst Terminal USB Model (UTU) Manual

8. The following dialog window will appear, and select to delete or not to delete installation

history files before uninstallation, then click the [Next >] button. Selecting “Yes” is

recommended.

9. The following dialog window will appear, and uninstallation of software begins.

10. Click the [Finish] button after appearing dialog window as shown below.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 40 -

iBurst Terminal USB Model (UTU) Manual

Uninstallation for Windows XP

Uninstallation for Windows XP Uninstallation for Windows XP

1. Close all programs that are currently running.

2. Disconnect the iBurst Terminal from your PC.

3. Click the [Start] button, and click [Control Panel] to open Control Panel, and then double click

[Add or Remove Programs].

4. Select [iBurst Terminal] software, and click the [Remove] button.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 41 -

iBurst Terminal USB Model (UTU) Manual

5. Click the [OK] button after appearing dialog window as shown below.

6. The following dialog window will appear, and select to delete or not to delete installation

history files before uninstallation, then click the [Next >] button. Selecting “Yes” is

recommended.

7. The following dialog window will appear, and uninstallation of software begins.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 42 -

iBurst Terminal USB Model (UTU) Manual

8. Click the [Finish] button after appearing dialog window as shown below.

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 43 -

Ap

Appendix

pendix

ApAp

pendixpendix

iBurst Terminal USB Model (UTU) Manual

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 44 -

iBurst Terminal USB Model (UTU) Manual

Utility software will be not uninstalled when b

Utility software will be not uninstalled when back

Utility software will be not uninstalled when bUtility software will be not uninstalled when b

If you uninstall the latest iBurst Terminal software by executing the old software package on

Windows Vista and you restart the PC, you will find a warning pop-up message “Help path isn’t

found.” and will find the utility software on the task tray against UNINSTALLING.

To clear this situation, please install the latest one again and uninstall it following the standard

procedure from “Add/Remove Programs” on “Control Panel” shown in this manual.

Trouble when disabling a bui

Trouble when disabling a builllltttt----in wireless LAN

Trouble when disabling a buiTrouble when disabling a bui

On some particular models of Windows PC, disabling a built-in wireless LAN device on “Device

Manager” will make a trouble that the PC doesn’t recognize iBurst User Terminals, not only iBurst

devices, when attaching or removing it. Since such PC shall have a wireless LAN utility to

control and monitor wireless LAN devices, please turn the wireless LAN device off by utilizing the

in wireless LAN device on Windows PC

in wireless LAN in wireless LAN

ack----to

to----date

date on Windows

ackack

toto

device on Windows PC

device on Windows PC device on Windows PC

on Windows Vis

date date

on Windows on Windows

Vista

ta

VisVis

tata

utility to avoid such trouble if you want to disable it.

FCC Compliance Statement

FCC Compliance Statement FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 45 -

iBurst Terminal USB Model (UTU) Manual

▬

Reorient or relocate the receiving antenna.

▬

Increase the separation between the equipment and receiver.

▬

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

▬

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

This equipment has been tested for compliance with FCC RF exposure limits in the laptop

computer(s) configurations with a USB port and can be used in laptop computers with

substantially similar physical dimensions, construction, and electrical and RF characteristics.

And also this equipment has been tested with original antenna.

Note

If this equipment is intended for use in any other portable device, you are responsible for

separate approval to satisfy the SAR requirements of Part 2.1093 of FCC rules.

FCC RF Radiation Exposure Statement

FCC RF Radiation Exposure StatementFCC RF Radiation Exposure Statement

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

The available scientific evidence does not show that any health problems are associated with using

low power wireless devices. There is no proof, however, that these low power wireless devices are

absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the

microwave range while being used. Whereas high levels of RF can produce health effects (by

heating tissue), exposure to low-level RF that does not produce heating effects causes no known

adverse health effects. Many studies of low-level RF exposures have not found any biological

effects. Some studies have suggested that some biological effects might occur, but such findings

have not been confirmed by additional research.UTU03-1890F-US-A has been tested and found to

comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the

FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.

[The end of this manual]

Kyocera Corporation S40T-EE005 Rev.1.00 Oct.28.2008

- 46 -

Kyocera IUU19AC Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual