KYLAND Technology SICOM3028GPT, SICOM3424GPT, SICOM3424GP, SICOM3028GP Hardware Installation Manual
SICOM3028GPT/3424PT/3028GP/3424P
Series Industrial Ethernet Switch
Hardware Installation Manual
Kyland Technology Co., LTD.
Publication Date: Mar. 2012
Version: V1.2
Customer Service Hotline: (+8610) 88796676
FAX: (+8610) 88796678
Website: http://www.kyland.cn
E-mail: support@kyland.biz
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
1
SICOM3028GPT/3424PT/3028GP/3424P Series Industrial Ethernet Switch
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. T his document i s not g uaranteed t o b e
error-free, and we reserve the right to amend it without notice to users.
Copyright © 2012 KYLAND Technology CO., LTD.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, i n any form or by any m eans without t he pr ior w ritten permission o f
KYLAND Corporation.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
2
Notice for Safety Operation
This pr oduct per forms reliably as long as it is used acc ording t o t he g uidance.
Artificial damage or destruction of the equipment should be avoided.
Read this manual carefully and keep it for future reference;
Do not place the equipment near water sources or damp areas;
Do not place anything on power cable or put the cable in unreachable places;
Do not tie or wrap the cable, which may cause a fire risk;
Power co nnectors and ot her eq uipment co nnectors should be f irmly
interconnected and checked frequently;
Do no t r epair t he equipment by y ourself, unless it i s clearly specified i n t he
manual;
Please keep the equipment clean; if necessary, wipe the equipment with soft
cotton cloth.
In t he following cases, please immediately shut down your power s upply and
contact your Kyland representative:
Water gets into the equipment;
Equipment damage or shell damage;
Equipment operation or performance has abnormally changed;
The equipment emits odor, smoke or abnormal noise.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
3
Contents
1 Packing List ......................................................................................................... 5
2 Product Overview ............................................................................................... 5
3 Structure and Interface ....................................................................................... 6
3.1 Front Panel .................................................................................................. 6
3.2 Rear Panel .................................................................................................. 6
3.2.1 Rear Panel 1U Slot ............................................................................ 7
3.2.2 Rear Panel 0.5U Slot ......................................................................... 8
4 Interface Modules Mounting .............................................................................. 9
4.1 Interface Modules Mounting ...................................................................... 10
4.2 Interface Modules Removal ....................................................................... 12
5 Switch Chassis Mounting ................................................................................ 16
5.1 Dimension Drawing ................................................................................... 16
5.2 Mounting Steps ......................................................................................... 17
6 Cable Connection ............................................................................................. 19
6.1 10/100Base-T(X) Ethernet Port ................................................................. 19
6.2 100Base-FX Ethernet Port ........................................................................ 21
6.3 10/100/1000Base-T(X) Ethernet Port ........................................................ 22
6.4 1000Base-X, 10/100/1000Base-T(X) SFP Port ......................................... 23
6.4.1 Gigabit SFP Optical Module ............................................................. 23
6.4.2 Gigabit SFP Electrical Module ......................................................... 25
6.5 Console Interface ...................................................................................... 26
6.6 Power ........................................................................................................ 27
6.7 Grounding .................................................................................................. 28
6.8 Relay Contact ............................................................................................ 29
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
4
7 LED Indicators .................................................................................................. 29
8 Power-on Self-inspection ................................................................................. 31
9 Management Access ...................................................................................... 32
9.1 Connected through Console Port .............................................................. 32
9.2 Connected through Ethernet Cable ........................................................... 34
9.3 Web Access ............................................................................................... 35
10 Product Configuration Information ................................................................. 36
11 Basic Features and Specifications .................................................................. 38
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
5
1 Packing List
Industrial Ethernet Switch 1
CD (including Hardware Installation Manual, Web Operation Manual and
Windows utility) 1
Screwdriver 1
Mounting Bracket 2
Puller 1
Certificate of Quality (including Certificate of Compliance) 1
Note: After unpacking, please check the accessories and the appearance of the equipment. If
anything is missing or damaged, please contact us.
2 Product Overview
The s eries switches include SICOM3028GPT/3424PT/3028GP/3424P layer 2
switch as shown i n Table 1.They al l ad opt f lexible modular desi gn f or easy
expansion.
Table 1 Product Model
Model
Interface Description
PTP
SICOM3028GPT
Supports max 28 Gigabit ports
Supported
SICOM3424PT
Supports max 4 G igabit por ts and 24 f ast
Ethernet ports Supported
SICOM3028GP
Supports max 28 Gigabit ports
Unsupported
SICOM3424P
Supports max 4 G igabit por ts and 24 f ast
Ethernet ports Unsupported
The series switches support 19 inch 1U Rack mounting by their front/rear panel.
They provide one 1U slot and six 0.5U slots in the rear panel, applied extensively
in power, rail transit, coal mining and many other industries. They are compliant
with IEC61850-3 an d I EEE1613; provide Mini U SB C onsole p ort; su pport
IEC62439-6; support VCT (Virtual Cable Test).
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
6
3 Structure and Interface
3.1 Front Panel
Figure 1 Front Panel
1: Alarm-Alarm LED
2: Run-Running LED
3: Ring-Ring LED
4: Lock-Synchronization Finish LED
5: PWR2-Power 2 LED
6: PWR1-Power 1 LED
7: Slot (1-7) Speed (1-4)-4 port Speed LEDs (Slot (1-7))
8: Slot (1-7) Link/ACT (1-4)-4 port Link/ACTLEDs ((Slot (1-7))
9: Console-Console interface (Mini USB)
10: USB interface (for future release)
11: Front mounting bracket
3.2 Rear Panel
Figure 2 Rear Panel
1: 1U Slot1 for 4-port Gigabit interface module
2: 0.5U Slot2 for 4-port Ethernet interface module
3: 0.5U Slot3 for 4-port Ethernet interface module
4: 0.5U Slot4 for 4-port Ethernet interface module
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
7
5: 0.5U Slot5 for 4-port Ethernet interface module
6: 0.5U Slot6 for 4-port Ethernet interface module
7: 0.5U Slot7 for 4-port Ethernet interface module
8: Alarm contact
9: Grounding screw
10: Terminal block for power input
11: Rear mounting bracket
3.2.1 Rear Panel 1U Slot
SM6.6-4GX-1U
SM6.6-4GX-1U：
4 1000Base-X, 10/100/1000Base-T(X) SFP ports
Figure 3 SM6.6-4GX-1U
SM6.6-2GX-2GE-1U
SM6.6-2GX-2GE-1U：
2 1000Base-X, 10/100/1000Base-T(X) SFP ports
2 10/100/1000Base-T(X) RJ45 ports
Figure 4 SM6.6-2GX-2GE-1U
SM6.6-4GE-1U
SM6.6-4GE-1U:
4 10/100/1000Base-T(X) RJ45 ports
Figure 5 SM6.6-4GE-1U
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
8
3.2.2 Rear Panel 0.5U Slot
SM6.6-4GX-0.5U
Figure 6 SM6.6-4GX-0.5U
SM6.6-4GX-0.5U: 4 1000Base-X, 10/100/1000Base-T(X) SFP ports
SM6.6-2GX-2S/M-0.5U
Figure 7 SM6.6-2GX-2S/M-0.5U
SM6.6-2GX-2S/M-0.5U:
2 1000Base-X, 10/100/1000Base-T(X) SFP ports
2 100Base-FX, SM/MM ports, FC/SC/ST connector
SM6.6-4GE-0.5U
Figure 8 SM6.6-4GE-0.5U
SM6.6-4GE-0.5U: 4 10/100/1000Base-T(X) RJ45 ports
SM6.6-2GX-2GE-0.5U
Figure 9 SM6.6-2GX-2GE-0.5U
SM6.6-2GX-2GE-0.5U:
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
9
2 1000Base-X, 10/100/1000Base-T(X) SFP ports
2 10/100/1000Base-T(X) RJ45 ports
SM6.6-4S/M-0.5U
Figure 10 SM6.6-4S/M-0.5U
SM6.6-4S/M-0.5U:
4 100Base-FX, SM/MM ports, FC/SC/ST connector
SM6.6-2S/M-2T-0.5U
Figure 11 SM6.6-2S/M-2T-0.5U
SM6.6-2S/M -2T-0.5U:
2 100Base-FX, SM/MM ports, FC/SC/ST connector
2 10/100Base-T(X) RJ45 ports
SM6.6-4T-0.5U
Figure 12 SM6.6-4T-0.5U
SM6.6-4T-0.5U: 4 10/100Base-T(X) RJ45 ports
4 Interface Modules Mounting
Note: We recommend that the interface modules be installed and removed while the power is
disconnected.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
10
4.1 Interface Modules Mounting
The series switches provide one 1U Slot (Slot1) and six 0.5U Slots (Slot2-Slot7) in
the rear panel as shown in Figure 2. Interface modules can be installed into slots
as needed. The models of the interface modules are shown in Table 11.
Note: Not all the slots need to be installed with the interface modules; you can choose the
appropriate slots according to specific requirements.
0.5U interface modules installation in upper slots(Slot2,Slot4 and Slot6)
Step 1: C hoose the appropriate 0.5U interface m odule. Insert the interface
module with the port numbers (1, 2, 3, 4) facing up . I nsert t he g uide r ail of
interface module into the guide rail slot, as shown in Figure 13 , and t hen
push the interface module into the slot completely along the guide rail slot.
Figure 13 0.5U Interface Module Mounting 1
Step 2: Secure the interface module into the switch chassis with two screws
(M2.5×5), as shown in Figure 14.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
11
Figure 14 0.5U Interface Module Mounting 2
0.5U interface modules installation in lower slots(Slot3,Slot5 and Slot7)
Step 1: C hoose the appropriate 0 .5U i nterface module. Insert the i nterface
module with the port numbers (1, 2, 3, 4) upside down. Insert the guide rail of
interface module into the guide rail slot, as shown in Figure 15, and then push
the interface module into the slot completely along the guide rail slot.
Figure 15 0.5U Interface Module Mounting 3
Step 2: Secure the interface module into the switch chassis with two screws
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
12
(M2.5×5), as shown in Figure 16 .
Figure 16 0.5U Interface Module Mounting 4
1U interface modules mounting in Slot1
The installation instructions for 1U interface modules in Slot1 are the same as
in upper slots (Slot2, Slot4 and Slot6). Please refer to the instructions above.
4.2 Interface Modules Removal
0.5U interface modules removal
When removing the 0.5U interface modules, a puller as shown in Figure 17 is
needed.
Figure 17 Puller
The specific mounting steps are as follows: (removal for upper and lower slots
is the same)
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
13
Step 1: Remove the two fastening screws of the interface module and switch
chassis.
Step 2: Insert the long tab into the handle of the interface module, as shown in
Figure 18; then move the puller left to ensure adequate space for inserting the
short tab.
Figure 18 Interface Modules Removal 1
Step 3: Insert the short tab of the puller into the other handle of the interface
module as shown in Figure 19; move the puller to the right to keep both of the
tabs inserted into the two handles of the interface module, as shown in Figure
20.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
14
Figure 19 Interface Modules Removal 2
Figure 20 Interface Modules Removal 3
Step 4: Grip the handle of puller; push the handle in the direction of arrow 1
with your t humb, an d at t he sa me t ime pull the handle out wards with your
fingers in the direction of arrow 2. The i nterface module will pop-up. Pull the
interface module outwards along the guide rail slot, until it completely comes
out of the switch chassis.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
15
Figure 21 Interface Modules Removal 4
Note: When using the puller, ensure to insert the long tab into the handle of the interface module
first and then insert the short tab; otherwise the long and s hort tabs will not be inserted into the
handles because of the specific design of the puller.
1U interface modules removal
Step 1: Remove the three fastening screws o f the i nterface m odules and
switch chassis.
Step 2: Pull the handle of the interface module outwards along the guide rail
slot, until i t co mpletely comes out of the switch chassis, as shown in Figure
22.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
16
Figure 22 Interface Modules Removal 5
5 Switch Chassis Mounting
5.1 Dimension Drawing
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
17
Figure 23 Mounting Dimension Drawing
Note: The switch housing is part of the heat dissipation system, which becomes hot during
operation. Please use caution when coming in contact and avoid covering the ventilation
holes of the switch housing when the switch is operating.
5.2 Mounting Steps
The series switches support rack mounting by its front/rear panel.
The steps of mounting by the front panel
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
18
Step 1: Select the mounting position for the switch in the rack and ensure that
there is adequate space for it.
Step 2: As shown in Figure 24, move the switch in the direction of arrow 1 and
align the holes in the switch mounting brackets and the corresponding holes
in the rack; use 4 screws (M5×14) to fix the switch in the rack.
Figure 24 Mounting by Front Panel
Removal steps
Step 1: U nscrew 4 sc rews fastening t he switch and t he r ack as shown i n
Figure 25.
Step 2: Remove the switch from the rack along the direction of arrow 1.
Figure 25 Removal
The steps of mounting by the rear panel
Step 1: Select the mounting position for the switch in the rack and ensure that
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
19
there is adequate space for it.
Step 2: As shown in Figure 26, move the switch in the direction of arrow 1 and
align the holes in the mounting br ackets and the corresponding holes in the
rack; use 4 screws (M5×14) to fix the switch in the rack.
Figure 26 Mounting by Rear Panel
Removal steps
Step 1: U nscrew 4 sc rews fastening t he switch and t he r ack as shown i n
Figure 27.
Step 2: Remove the switch from the rack along the direction of arrow 1.
Figure 27 Removal
6 Cable Connection
6.1 10/100Base-T(X) Ethernet Port
10/100Base-T(X) Ethernet RJ45 port can be connected to terminal equipment and
network devices with st raight-through c ables or cr ossover ca bles. R J45
connectors must be equipped at both ends of cable.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
20
Pin definition of 10/100Base-T(X) RJ45 port
Pin number of 10/100Base-T(X) RJ45 port is shown in Figure 28
Figure 28 RJ45 Port
Pin definition of 10/100Base-T(X) RJ45 port is shown in Table 2
Table 2 Pin Definition of 10/100Base-T(X) RJ45 Port
Pin
MDI-X Signal Name
MDI Signal Name
1
Receive Data+(RD+)
Transmit Data+(TD+)
2
Receive Data-(RD-)
Transmit Data-(TD-)
3
Transmit Data+(TD+)
Receive Data+(RD+)
6
Transmit Data-(TD-)
Receive Data-(RD-)
4, 5, 7, 8
Unused
Unused
Note: “+”“-”means level polarity.
Wiring Sequence
Figure 29 10/100M Straight-through Cable Wiring
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
21
Figure 30 10/100M Cross-over Cable Wiring
6.2 100Base-FX Ethernet Port
100Base-FX Ethernet port is equipped with FC/SC/ST connector, and each port
consists of TX (transmit) port and RX (receive) port, as shown on the left in Figure
31.
100Base-FX port wiring is shown on the right in Figure 31 (Take SC port as
example; ST/FC wiring method is the same with SC). Connect the TX (transmit)
port of switch A to the RX (receive) port of switch B, and the RX (receive) port of
switch A to the TX (transmit) port of switch B in order to transmit data between
switch A and switch B.
Figure 31 100Base-FX Port Wiring
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
22
Note: A laser is used to transmit signals in fiber cables. The laser meets the requirements of
level 1 laser products. Routine operation is not harmful to your eyes, but do not look directly
at the fiber port or fiber connector when the switch is powered on.
6.3 10/100/1000Base-T(X) Ethernet Port
10/100/1000Base-T(X) E thernet R J45 por t can be co nnected t o t erminal
equipment and network devices with straight-through cables or crossover cables.
RJ45 connectors must be equipped at both ends of cable.
Pin definition of 10/100/1000Base-T(X) RJ45 port
Pin number of 10/100/1000Base-T(X) RJ45 port is shown in Figure 32.
Figure 32 RJ45 Port
Pin definition of 10/100/1000Base-T(X) RJ45 port is shown in Table 3.
Table 3 Pin Definition of 10/100/1000Base-T(X) RJ45 Port
Pin MDI MDI-X
1 Transmit/Receive Data(TRD0+)
Transmit/Receive Data(TRD1+）
2 Transmit/Receive Data(TRD0-) Transmit/Receive Data(TRD1-)
3 Transmit/Receive Data(TRD1+) Transmit/Receive Data(TRD0+)
4 Transmit/Receive Data(TRD2+) Transmit/Receive Data(TRD3+)
5 Transmit/Receive Data(TRD2-) Transmit/Receive Data(TRD3-)
6 Transmit/Receive Data(TRD1-) Transmit/Receive Data(TRD0-)
7 Transmit/Receive Data(TRD3+) Transmit/Receive Data(TRD2+)
8 Transmit/Receive Data(TRD3-) Transmit/Receive Data(TRD2-)
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
23
Note: “+”“-”means level polarity.
Wiring Sequence
Figure 33 10/100/1000M Straight-through Cable Wiring
Figure 34 10/100/1000M Cross-over Cable Wiring
6.4 1000Base-X, 10/100/1000Base-T(X) SFP Port
1000Base-X, 10/ 100/1000Base-T(X) S FP p ort na mely i s 1000Base S FP sl ot.
Insert SFP module to SFP slot, and then plug twisted pair or optical fiber into SFP
module t o t ransmit d ata. Choose t he model of SFP m odule to m eet your
requirements, as shown in Table 12.
6.4.1 Gigabit SFP Optical Module
Figure 35 shows an example of a Gigabit SFP optical module;
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
24
Figure 35 Gigabit SFP Optical Module
Gigabit SFP op tical module is equipped w ith LC c onnector, an d each por t
consists of TX (transmit) por t and R X (receive) port, as shown on the left in
Figure 36.
Connect the TX (transmit) port of switch A to the RX (receive) port of switch B,
and the RX (receive) port of switch A to the TX (transmit) port of switch B in
order to transmit data between switch A and switch B, as shown on the right in
Figure 36.
Figure 36 Gigabit SFP Optical Module Wiring
Confirm Gigabit SFP optical module RX port and TX port
1. Insert the two connectors in one end of optical fiber into SFP optical module,
and then insert the two connectors in the other end of the optical fiber into
SFP optical module of another switch to communicate.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
25
2. Check the corresponding port Link/ACT indicator in the front panel:
Indicator flashing means link connectivity;
Indicator o ff means no l ink connectivity and i t may be b ecause of the
incorrect link between RX port and TX port in SFP optical modules. Try to
swapping connectors in any one end of optical fiber.
The use of SFP optical module
While wiring, first insert the SFP optical module into the SFP slot in the switch,
and then plug the optical fiber into the SFP optical module. See Figure 37.
Figure 37 SFP Optical Module
6.4.2 Gigabit SFP Electrical Module
Figure 38 shows an example of a Gigabit SFP electrical module;
Figure 38 Gigabit SFP Electrical Module
The use of SFP electrical module
While wiring, first insert the SFP electrical module into the SFP slot in the
switch, and then plug the twisted pair into the SFP electrical module. See
Figure 39.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
26
Figure 39 SFP Electrical Module
6.5 Console Interface
Install the driver for Mini USB onto your PC. The driver “Mini USB driver.exe” is in
the software download folder, which i s on the s upplied C D. Connect the U SB
port on t he PC to the Console interface on the switch with ca ble equipped with
Mini U SB co nnector and U SB c onnector at b oth ends. R un Hyper T erminal
software in WINDOWS o perating sy stem to co nnect t o console s oftware of the
switch, which will allow you to configure, maintain and manage the switch.
Mini USB connector
Mini USB connector pin number is shown in Figure 40.
Figure 40 Mini USB Connector
Mini USB connector pin definition is shown in Table 4.
Table 4 Mini USB Pin Definition
Mini USB Pin
Definition
1
VBUS
2
D- 3 D+ 4 ID 5 GND
USB connector
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
27
USB connector pin number is shown in Figure 41.
Figure 41 USB Connector
USB pin definition is shown in Table 5.
Table 5 USB Pin Definition
USB Pin
Definition
1
VBUS
2
D-
3
D+
4
GND
6.6 Power
According to the power input requirements, use a 5.08mm-spacing terminal block
to connect power cable.
Note: The cross section area of power cable is required to be greater than 0.75mm2 and
less than 2.5mm
2
. The grounding resistance requirement: <5Ω.
5 pin 5.08mm power terminal block
Figure 42 5-pin 5.08mm-spacing Plug-in Terminal Block
Table 6 5 Pin 5.08mm Power Terminal Block Contact Definition
Contact Number DC Wiring Definition AC Wiring Definition
1 PWR1: + PWR1: L
2 PWR1: - PWR1: N
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
28
3 Protection Ground Protection Ground
4 PWR2: - PWR2: N
5 PWR2: + PWR2: L
Wiring and mounting
Step 1: Take the power terminal block off the switch.
Step 2: Insert the power cable into the terminal block and connect the power
cable.
Step 3: Put the terminal block back to the switch with the connected cable.
6.7 Grounding
There is a grounding screw on t he rear panel of the switch, which is for chassis
grounding. One e nd of t he c hassis grounding ca ble i s connected w ith t he
grounding screw and the other end of the cable is reliably grounded.
Figure 43 Grounding
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
29
Note: T he cross section ar ea of chassis grounding ca ble should be more than 2. 5mm2. T he
grounding resistance requirement: <5Ω.
6.8 Relay Contact
The relay contact is used for alarm output. When the switch works normally, the
normally-open co ntact of t he al arm r elay is closed a nd t he n ormally-closed
contact is open; when the alarm occurs, the normally-open contact is open an d
the nor mally-closed c ontact is closed. The al arm i s outputted through a 3-pin
5.08mm spacing terminal block as shown in Figure 44.
Figure 44 3-pin 5.08mm Spacing Alarm Terminal Block
The electrical parameters of the relay:
Max Switch Voltage: 250VAC/220VDC;
Max Switch Current: 2A
Max Switch Power: 60W
Note: P in 1 a nd pin 2 are nor mally-open c ontacts; pi n 2 an d pi n 3 ar e normally-closed
contacts. When the switch works normally, the pin 1 and 2 are closed, pin 2 and pin 3 are
open; when the alarm occurs, the pin 1 and 2 are open; pin 2 and 3 are closed.
Wiring and mounting
Step 1: Take the alarm terminal block off the switch.
Step 2: Insert the cable for alarm output into the alarm terminal block according to
the requirements and fix the cable.
Step 3: Put the alarm terminal block back to the switch with the connected cable.
7 LED Indicators
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
30
Table 7 SICOM3028GPT/3424PT/3028GP/3424P Front Panel LEDs
LED State Description
System Running LED
Run
ON
CPU operates abnormally or the switch is in the
power on and startup process
Blinking
(1Hz)
CPU operates normally
OFF CPU does not start up
Alarm LED
Alarm
Blinking
(5Hz)
System alarm
OFF No system alarm
Power LEDs
PWR1
ON Power 1 connects and operates normally.
OFF Power 1 disconnects or operates abnormally.
PWR2
ON Power 2 connects and operates normally.
OFF Power2 disconnects or operates abnormally.
Ring LED
Ring
Blinking Ring mode and the switch is slave of ring.
ON Ring mode and the switch is master of ring.
OFF No ring mode.
Synchronization Finish LED
Lock
ON The switch has finished PTP synchronization.
Blinking(1HZ) PTP synchronizing.
OFF The switch does not st art up with PTP
synchronization.
Port LEDs
Speed 10/100/1000Base-T(X)
ON 1000M working state
OFF 10/100M working state or no connection
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
31
1000Base-X
ON 1000M working state
OFF 100M working state or no connection
10/100Base-T(X)
ON 100M working state
OFF 10M working state or no connection
100Base-FX
ON 100M working state
OFF no connection
Link/ACT
ON Effective network connection in the port
Blinking Network activities in the port
OFF No effective network connection in the port
Table 8 SICOM3028GPT/3424PT/3028GP/3424P Rear Panel LEDs
Note: The 100M port Speed LEDs in the front and rear of SICOM3028GPT and SICOM3028GP
panel are never on.
8 Power-on Self-inspection
Once the power is on, all the port LEDs in the front panel will be on for a short time,
LED State Description
RJ45 Port LEDs
Each RJ45 port has two indicators, a yellow LED and a green LED. The yellow LED indicates port
rate, while the green LED indicates port connection state.
Speed
(Yellow)
10/100/1000Base-T(X)
ON 1000M working state
OFF 10/100M working state or no connection
10/100Base-T(X)
ON 100M working state
OFF 10M working state or no connection
Link/ACT
ON Effective network connection in the port
Blinking Network activities in the port
OFF No effective network connection in the port
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
32
proving that the corresponding ports are operating normally.
9 Management Access
Access the switch by one of the following three ways.
9.1 Connected through Console Port
1. Install the driver for Mini USB onto your PC. The driver “Mini USB driver.exe” is
in the software download folder, which is on the supplied CD.
2. Use the Console cable t hat i s equipped with Mini U SB c onnector at one end
and U SB c onnector a t t he ot her en d t o co nnect t he C onsole i nterface o n t he
switch with the USB port on PC.
3. On Windows desktop, cl ick Start → All programs → Accessories →
Communications → Hyper Terminal.
Figure 45 Hyper Terminal
4. Build a new connection named “aa”
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
33
Figure 46 New Connection
5. Select COM port as the connection type.
Figure 47 Choose Port
6. Set the parameters of COM port (Bits per second: 115200, Data bits: 8, Parity:
None, Stop bits: 1, Flow control: None)
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
34
Figure 48 Set COM Parameters
7. Click “OK” to enter the CLI interface, and type in a CLI command from Table 9.
Table 9 CLI Command
View
Command
Description
User View
SWITCH>enable
Enter management view
Management View
SWITCH#show i nterface
vlan 1
Show t he default IP addr ess of cu rrent
switch
Management View
SWITCH#show version
Show version of the switch
Management View
SWITCH#reload
Reboot
Management View
SWITCH#set default
SWITCH#write
Reload factory default settings
Management View
SWITCH#config terminal
Enter configuration view
9.2 Connected through Ethernet Cable
1. Connect any RJ45 port o f t he switch with t he E thernet por t of a per sonal
computer with a RJ45 cable.
2. Open Run window from the start menu, then input “telnet + ‘IP address’”. Click
“OK” to enter the Telnet interface. The default IP address is 192.168.0.2.
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
35
Figure 49 Enter Telnet
3. Click “OK”, and input a default user name “admin” and password “123” to enter
the Telnet configuration interface, see Figure 50.Type in a CLI command from
Table 9.
Figure 50 Telnet Configuration Interface
9.3 Web Access
1. Connect the Ethernet port on the PC to any RJ45 port on the switch.
2. Input t he I P a ddress of the current switch in w eb browser, the default IP is
192.168.0.2. The W eb interface access screen will appear as shown below i n
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
36
Figure 51, login with default user name “admin” and password “123”.
Figure 51 Access Web Interface
10 Product Configuration Information
Table 10 SICOM3028GPT/3424PT/3028GP/3424P Chassis Tabl e
Model
Slot
Power
0.5U Slot
1U Slot
SICOM3028GPT-Chassis 6 1
24DC,48DC,
220AC/DCW
redundant
SICOM3424PT-Chassis 6 1
SICOM3028GP-Chassis 6 1
SICOM3424P-Chassis 6 1
Table 11 SICOM3028GPT/3424PT/3028GP/3424P Interface Modules
Model Description Remark
SM6.6-4GX-0.5U
0.5U interface module, supports 4
1000Base-X,10/100/1000Base-T(X)SFP ports
Only
SICOM3028GPT,
SICOM3028GP
SM6.6-2GX-2S/M-0.5U
0.5U interface module, supports 2
1000Base-X,10/100/1000Base-T(X)SFP ports; 2
100Base-FX,SM/MM ports, FC/SC/ST connector
Only
SICOM3028GPT,
SICOM3028GP
SM6.6-4GE-0.5U
0.5U interface module, supports 4
10/100/1000Base-T(X) RJ45 ports
Only
SICOM3028GPT,
SICOM3028GP
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
37
SM6.6-2GX-2GE-0.5U
0.5 interface module, supports 2
1000Base-X,10/100/1000Base-T(X)SFP ports; 2
10/100/1000Base-T(X) RJ45 ports
Only
SICOM3028GPT,
SICOM3028GP
SM6.6-4S/M-0.5U
0.5U interface module, supports 4
100Base-FX,SM/MM ports, FC/SC/ST connector
For al l pr oduct
models
SM6.6-2S/M -2T-0.5U
0.5U interface module, supports 2
100Base-FX,SM/MM ports, FC/SC/ST connector
2 10/100Base-T(X) RJ45 ports
For al l pr oduct
models
SM6.6-4T-0.5U
0.5U interface module, supports 4 10/100Base-T(X)
RJ45 ports
For al l pr oduct
models
SM6.6-4GX-1U
1U interface module, supports 4
1000Base-X,10/100/1000Base-T(X)SFP ports
For al l pr oduct
models
SM6.6-2GX-2GE-1U
1U interface module, supports 2
1000Base-X,10/100/1000Base-T(X)SFP ports; 2
10/100/1000Base-T(X) RJ45 ports
For al l pr oduct
models
SM6.6-4GE-1U
1U interface module, supports 4
10/100/1000Base-T(X) RJ45 ports
For al l pr oduct
models
SM6.6-GPS-OI-0.5U
GPS clock synchronization module, conversion from
GPS signal to PTP,
support one GPS signal input port,
one PPS output port
Only
SICOM3028GPT,
SICOM3424PT
SICOM6028GPT
SICOM6424PT
SM6.6-PTP-BO-0.5U
IRIG-
B P TP clock c onverter output module,
conversion f rom PTP t o IRIG-B out put,
two
IRIG-B(DC) output ports, two IRIG-
B(AC) output ports,
one PPS output port
Only
SICOM3028GPT,
SICOM3424PT
SICOM6028GPT
SICOM6424PT
Table 12 SICOM3028GPT/3424PT/3028GP/3424P Optional Accessories
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
38
Model Description
DT-FCZ-RJ45-01 RJ45 dustproof shield
DT-XL-Mini USB-USB-2m USB console cable, Mini USB to USB, 2m
Gigabit SFP Module
IGSFP-TX-RJ45 10/100/1000Base-T(X) RJ45 port; transmission distance is 100m
IGSFP-M-SX-LC-850-0.55 1000Base-X port; multi mode, LC connector; w avelength is 850nm,
transmission distance is 550m
IGSFP-S-LX-LC-1310-10 1000Base-X
port; si ngle m ode, LC co nnector; w avelength i s
1310nm, transmission distance is 10Km
IGSFP-S-LH-LC-1310-40 1000Base-
X por t; si ngle m ode, LC co nnector; w avelength i s
1310nm, transmission distance is 40Km
IGSFP-S-ZX-LC-1550-60 1000Base-X por t; si ngle m ode,
LC co nnector; w avelength i s
1550nm, transmission distance is 60Km
IGSFP-S-ZX-LC-1550-80 1000Base-
X por t; si ngle m ode, LC co nnector; w avelength i s
1550nm, transmission distance is 80Km
11 Basic Features and Specifications
Power Requirements
Power module: 24DC (18~36VDC),
or 48DC( 36~72VDC)
or 220AC/DCW (77~300VDC/85~264VAC)
Power terminal: 5-pin 5.08mm-spacing plug-in terminal block
Power consumption: <40W
Physical Characteristics
Housing:Metal,fanless
Installation: 19 inch 1U Rack mounting
SICOM3028GPT/3424PT/3028GP/3424P User’s Manual-v1.2
39
Dimensions (W×H×D): 482.6mm×44mm×360mm
Weight: <10Kg( 22.046 pound)
Environment Limits
Operating Temperature: -40℃ to 85℃
Storage Temperature: -40℃ to 85℃
Ambient Relative Humidity: 5% to 95% (non-condensing)
MTBF
SICOM3028GPT/3424PT: 359000h
SICOM3028GP/3424P: 360000h
Warranty
5 years
For more information about KYLAND products, please visit our website:
http://www.kyland.cn/
Loading...