KYLAND Technology SICOM3024SM User Manual

SICOM3024SM Industrial Ethernet Switch

User’s Manual

KYLAND Technology Co., Ltd.

SICOM3024SM Industrial Ethernet Switch User’s Manual

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of KYLAND Corporation.

Publisher：KYLAND Technology CO., LTD.

Address：Chongxin Creative Building, Shixing East Road 18#, Shijingshan District,

Beijing, China

Website：http://www.kyland.cn

postcode：100041

Tel ：（+8610）88796676

FAX ：（+8610）88796678

E-mail：sales@kyland.biz

Ve r si o n ：V1, Jan. 2008

V2, Aug. 2009

No.：27030030-20

Preface

SICOM3024SM is a high-performance Gigabit industrial Ethernet switch specially designed by

KYLAND Technology CO., LTD. for industrial applications. The ports of SICOM3024SM

support POE function. IEEE802.3af, the standard of POE, divides power supply system into PSE

(Power-Sourcing Equipment) and PD (Powered Device). Its high-performance switch engine,

solid and closed case design, high-efficient single-ribbed casing for heat dissipation without fans,

over-current, overvoltage and EMC protection at power input side, and excellent EMC

protection of RJ45 port allow SICOM3024SM applicable in harsh and dangerous industrial

environments. The redundant function of optical fiber network and redundant power input

function provide multiplex guarantee for reliable operation of the system.

The user’s Manual for SICOM3024SM Industrial Ethernet Switch mainly introduces the

information on technical principles, performance indexes, installation and commissioning,

network management etc. to provide users with references in startup, expansion and routine

maintenance. It is a practical teaching material that can be used for knowledge and

understanding of SICOM3024SM industrial Ethernet Switch.

This manual mainly includes the following contents:

Chapter 1 Overview and system features of SICOM3024SM industrial Ethernet switch;

Chapter 2 Performance and service functions of SIOCM3024SM industrial Ethernet switch;

Chapter 3 Hardware structure of SICOM3024SM industrial Ethernet switch;

Chapter 4 Installation of SICOM3024SM industrial Ethernet switch;

Chapter 5 Field test methods for SICOM3024SM industrial Ethernet switch;

Chapter 6 Networking modes and system configuration of SICOM3024SM;

Chapter 7 WEB management of SICOM3024SM industrial Ethernet switch;

Appendix A Introduces twisted pair and pin distribution rules of SICOM3024SM industrial

Ethernet switch;

Appendix B Introduces cable types and specifications of SICOM3024SM industrial Ethernet

switch;

Appendix C Introduces abbreviations used in this manual.;

Appendix D FTP application of software upgrade.

Statement: as product and technology upgrades and improves constantly, the contents of this document may not completely accord with the actual product. For product upgrading information, please visit our company’s website or directly contact with our business representative.

Notice for Safety Operation

This product offers reliable performances as long as it is used within the designed

scope. Artificial damage or destruction of the equipment should be avoided.

z Carefully read this manual and well preserve this manual for future reference; z Do not place the equipments near water sources or damp places; z Do not place anything on power cable which should be placed in unreachable

places;

z Do not tie or wrap the cable to prevent fire. z Power connectors and connectors for other equipments should be firmly

interconnected and frequently checked.

In the following cases, please immediately disconnect the power supply and

contact with our company:

1. Water gets into the equipments;

2. Equipment damage or shell breakage;

3. Abnormal operation conditions of equipment or the demonstrated

performances have changed;

4. The equipment emits odor, smoke or noise.

z Please keep optical fiber plugs and sockets clean. During operation of equipments,

do not stare directly into the cross section of optical fiber;

z Please keep the equipment clean; if necessary, wipe the equipment with soft

cotton cloth;

z Do not repair the equipment by yourself, unless it is clearly specified in the

manual.

Explanation of Warning Marks:

This manual uses two kinds of noticeable warning signs to arouse special attention

of users during operation. The implications of these signs are as follows:

Warning: pay special attention to the notes behind the mark,

improper operation will result in serious damage of the switch or

injury of operation personnel.

Caution, attention, warning, danger: remind the positions

requiring attention during operation.

CONTENTS

Chapter 1 System Overview...............................................................................................................- 1 -

1.1 Product Overview .......................................................................................................................- 1 -

1.2 System Features ..........................................................................................................................- 1 -

1.3 Packing list and unpacking check ...............................................................................................- 3 -

Chapter 2 Performance Specifications..............................................................................................- 5 -

2.1 System Specifications .................................................................................................................- 5 -

2.2 Service Interface .........................................................................................................................- 6 -

2.3 Service Function .........................................................................................................................- 7 -

Chapter 3 Hardware Structure........................................................................................................- 11 -

3.1 System Structure .......................................................................................................................- 11 -

3.2 Switch Structure........................................................................................................................- 11 -

3.2.1 Case...............................................................................................................................- 11 -

3.2.2 Front Panel ....................................................................................................................- 12 -

3.2.3 Back panel.....................................................................................................................- 13 -

Chapter 4 Hardware Installation.....................................................................................................- 21 -

4.1 Installation requirement ............................................................................................................- 21 -

4.2 Mainframe installation ..............................................................................................................- 21 -

4.2.1 Stable rack mounting.....................................................................................................- 21 -

Chapter 5 Test methods........................................................................................................................ 25

5.1 Self inspection............................................................................................................................... 25

5.2 TP Port Test................................................................................................................................... 25

5.3 POE Port Test................................................................................................................................ 25

5.4 Fiber Port Test............................................................................................................................... 26

Chapter 6 Networking and Configurations ....................................................................................- 29 -

6.1 Networking................................................................................................................................- 29 -

6.2 System configure.......................................................................................................................- 29 -

Chapter 7 WEB Management..........................................................................................................- 31 -

7.1 Login Web Page........................................................................................................................ - 31 -

7.2 Device Status Display...............................................................................................................- 32 -

7.2.1 Basic Info...................................................................................................................... - 32 -

7.2.2 Port State....................................................................................................................... - 33 -

7.2.3 Port Traffic Flow........................................................................................................... - 33 -

7.3 Device Basic Configuration...................................................................................................... - 34 -

7.3.1 Configure IP Address.................................................................................................... - 34 -

7.3.2 Configure Device Name ...............................................................................................- 35 -

7.3.3 Port Configuration ........................................................................................................ - 35 -

7.3.4 Change Password.......................................................................................................... - 36 -

7.3.5 Upgrade Software ......................................................................................................... - 36 -

7.3.6 Software Version........................................................................................................... - 37 -

7.3.7 Configure upload and download................................................................................... - 38 -

7.4 Device Advanced Configuration...............................................................................................- 38 -

7.4.1 Port Traffic Flow........................................................................................................... - 39 -

7.4.2 VLAN ........................................................................................................................... - 39 -

7.4.3 Port Mirroring............................................................................................................... - 41 -

7.4.4 Port Trunking................................................................................................................ - 42 -

7.4.5 Static Multicasting Address Table.................................................................................- 43 -

7.4.6 IGMP-snooping ............................................................................................................ - 45 -

7.4.7 SNMP Configuration .................................................................................................... - 46 -

7.4.8 Alarm configuration...................................................................................................... - 47 -

7.4.9 ACL Configuration....................................................................................................... - 48 -

7.4.10 RSTP Configuration......................................................................................................- 49 -

7.4.11 DT-Ring Configuration................................................................................................. - 50 -

7.4.12 POE Configuration .......................................................................................................- 53 -

7.4.13 QoS Configuration........................................................................................................ - 54 -

7.4.14 Other configuration....................................................................................................... - 57 -

7.4.15 RMON Configuration................................................................................................... - 58 -

7.5 Device Management ................................................................................................................. - 61 -

7.5.1 Restart........................................................................................................................... - 61 -

7.5.2 Logout........................................................................................................................... - 61 -

7.6 Configurations...........................................................................................................................- 61 -

7.7 Load Default .............................................................................................................................- 62 -

Appendix A T wisted-pair and Pin Distribution....................................................................................- 63 -

Appendix B Cable Type and Specifications..........................................................................................- 65 -

Appendix C Glossary..............................................................................................................................- 67 -

Appendix D FTP Application for Switch Software Update.................................................................- 69 -

Chapter 1 System Overview

- 1 -

Chapter 1 System Overview

1.1 Product Overview

SICOM3024SM is a high-performance Gigabit industrial Ethernet switch specially

SICOM3024SM support POE function. IEEE802.3af, the standard of POE, divides

power supply system into PSE (Power-Sourcing Equipment) and PD (Powered Device).

Its high-performance switch engine, solid and closed case design, high-efficient

single-ribbed casing for heat dissipation without fans, over-current, over-voltage and

EMC protection at power input side, and excellent EMC protection of RJ45 port allows

SICOM3024SM applicable in harsh and dangerous industrial environments. The

redundant function of optical fiber network and redundant power input function

provide multiplex guarantee for reliable operation of the system.

SICOM3024SM series Gigabit industrial Ethernet switch offers strong

web-management which support CLI, Telnet, WEB, SNMP and OPC-based network

management.

SICOM3024SM supports 2U 19 inch stable rack mounting for installation. There are

four uplink redundant 1000M SFP interfaces and max 24 10Base-T/100Base-TX ports

or 24 pairs of 100Base-FX（SM/MM）fiber ports in back panel. The redundant fiber or

TP cable ring of 1000Mbit can be connected by redundant SFP interfaces with recovery

time less than 50ms. Each RJ45 port is self-adaptive, automatically configured to

10Base-T or 100Base-TX and full-duplex or half-duplex. Auto MDI/MDI-X

connection is also available. It supports up to 24 RJ45 ports of 10Base-T/100Base-TX

with POE function.

1.2 System Features

1. High performance industrial Ethernet switch

Plug and play for 1000M SFP, changeable

4G fiber port provide various network for customers

4 100M modules, each module provides six fiber ports or RJ45 ports

SICOM3024SM Industrial Ethernet Switch User Manual

- 2 -

Support various management software, easy entrance for user such as: WEB, CLI,

TELNET, SNMP, OPC.

10Base-T/100Base-TX self-adaptive Ethernet connector (full/half duplex),

MDI/MDI-X auto-connection

100Base-FX full duplex SM/MM redundant fiber connector

Recovery time < 50ms increase the system reliability　

Broadcast storm control

IEEE802.3/802.U/802.3X store and forward

IGMP Snooping

Port mirroring

Port trunking

DT-Ring, DT-Ring+, RSTP protocols, etc

VLAN Tag

ACL function

Alarm function

SNMP protocol

POE function

802.1P, IP TOS, DSCP priority

Transparent transmission of VLAN Tag packets;

FTP-based online software upgrade, easy for equipment management and renewal

2. Industrial Power Design

Provide industrial power input: DC24V、DC48V、DC110V、AC220V、DC220V

Power input over-current, over-voltage protection and EMC

3. Rugged Design

Single-Ribbed heat-removal design (fanless); operation at -40℃ to +75℃

Solid and closed case design, IP40, can be used in harsh environment

Chapter 1 System Overview

- 3 -

1.3 Packing list and unpacking check

１. Packing list: see the packing list

２.Unpacking check

Before opening the case, place it stably, pay attention to the direction of the packing

case, and ensure its right side is facing upward, so as to prevent SICOM3024SM

from falling apart after opening the case. If a hard object is used to unclench the

case, do not overly extend the hard object into the case to avoid damage of the

equipments inside the case.

After opening the case, check the amount of SICOM3024SM equipments (including

main unit of SICOM3024SM, parts of equipment, user’s manual, customer service

guideline) according to the packing list, and check the appearance quality of

SICOM3024SM.

Warning:

For the built-in precise parts of equipments, please handle with care and avoid

strenuous vibration to avoid affecting the performances of equipments.

Chapter 2 Performance Specifications

- 5 -

Chapter 2 Performance Specifications

2.1 System Specifications

The system performance specifications of SICOM3024SM industrial Ethernet

switch are shown in Table 2-1.

Table 2-1 System Specs

Specs Description

Quantity of RJ45 port

24×10Base-T/100Base-TX

Quantity of Gigabit redundant port

4×1000Base-SFP connectors

Quantity of 100M redundant port

24×100Base-FX-SM/MM ports

Quantity of POE port

24×10Base-T/100Base-TX ports with POE function

System performance

Standard: IEEE802.3、IEEE 802.3x、IEEE 802.3u、IEEE802.3af、 IEEE802.3ab、IEEE802.3z、IEEE802.1q、IEEE802.1p、IEEE802.1d、

IEEE802.1w

Max Store-and-Forward speed: 1488100 bps

Max. filtering speed: 1488100 bps

Switching mode: Store-and-Forward

Switching bandwidth of system: 12.8G

Electromagnetic compatibility interference: EN55022

Electromagnetic compatibility immunity: EN50082-2

Ethernet Port

Physical port: shielded RJ-45

RJ-45 port: 10Base-T/100Base-TX, supporting automatic negotiation

function

Port standard: in line with IEEE802.3 standard

Transmission distance: <100m

Fiber port

Optical power: >-13dbm(SM) >-20dbm(MM)

Receiving sensitivity: <-28dbm(SM) <-35dbm(MM)

Wave length: 1310nm(SM) 1550nm(SM) 1310 nm(MM) Transmission distance: 20～80Km(SM) <5Km(MM)

Connector type: LC, SC/FC/ST

Transmission rate: 1.2Gbps (Gigabit), 125Mbps (100M)

PoE Port

Feeding power: DC24V: signal (1,2,3,6), Voltage: +(1,2,4,5) –(3,6,7,8)

DC48V: Signal (1,2,3,6) Voltage: +(4,5) –(7,8)

Max power consumption for each port: 29W

Max power consumption of the end of 100m cable for each port: 15.6W

Output voltage: DC24V, DC48V

Feeding input terminal: 5 cores 9.5mm space inserting terminal

Power supply Input voltage: DC24V(18V~36V), DC48V(36V~72V),

SICOM3024SM Industrial Ethernet Switch User Manual

- 6 -

DC110V(82V~185V),AC220V(85V~264),DC220V(120V~370V)

Input power consumption: 35W

Over-current Protection: build-in

Mechanical parameter

Physical dimensions (height´width´depth): 88 ㎜×482.6 ㎜×245 ㎜

Mounting mode: 19inch 2U stable rack mounting

Heat removal method: Single-ribbed aluminum casing for heat

dissipation without fan.

Outlet type: back outlet for service,

Shell protection: IP40 Weight: 6 ㎏

Ambient conditions

Operating temperature: -40℃～75℃ Storage temperature: -45℃～85℃ Humidity: 5%～95% （non-condensing）

2.2 Service Interface

1． 1 to 24 10Base-T/100Base-TX RJ45 ports，Each RJ45 port has self adaptation

function, capable of automatically configuring to 10Base-T or 100Base-TX state and

automatically working in full duplex or half duplex operation mode. Support

MDI/MDI-X auto-connection. The transmission distance is 100m max.

2． 1 to 24 pairs of redundant 100Base-FX single mode or multi-mode optical fiber

interfaces. The maximum throughput of each pair of optical fiber interface is 100Mbps,

and it is forced to work in 100M full duplex mode. They support optical fiber line

redundancy technology, with the recovery time less than 50ms.

3． Four redundant 100Base-LX/LC single mode or multi-mode optical fiber

interfaces or 10/100/1000Base-TX RJ45 ports. The maximum throughput of each pair

of optical fiber interface is 1000Mbps, and it is forced to work in 1000M full duplex

mode. They support optical fiber line redundancy technology, with the recovery time

less than 50ms.

4. Conform to IEEE802.3/802.3U/802.3X /802.3Z/802.ab/IEEE802.3af

5. Meanings of RJ45 port indicator: yellow lamp – rate indicator; on:100M, off:

10M; RJ45 Green lamp – connection state indicator, on: effective connection of

network; blink: network active; off: no connection. After power connection, all the

indicators light up. 30 seconds later, they work into the state described above

Chapter 2 Performance Specifications

- 7 -

2.3 Service Function

The service functions for SICOM3024SM mainly include:

LED Indicator

The LEDs (front panel) indicate the port status correctly including transmission rate,

link status and system status.

Layer-2 Switching

Switches work in two ways: Cut-Through and Store-and-Forward. In Cut-Through, a

data packet is immediately relayed further after detecting the target address; in

Store-and-Forward, a data packet is first read-in completely and checked for errors

before the switch relays the same. SICOM3024SM employs Store-and-Forward that is

a switching mode widely used.

VLAN

VLAN will divide one network into multiple logical subnets. Data packets cannot be

transmitted between different VLANs so as to control the broadcast domain and

segment flow and improve the reliability, security and manageability. SICOM3024SM

series supports IEEE802.1q VLAN tag. It can be divided into up to 4094 VLANs based

on ports. The VLAN division can be realized via WEB, CLI, etc. VLAN Tag packet is

transmitted transparently.

QoS Priority

IEEE 802.1p is the most popular priority solution in the LAN environment.

SICOM3024SM series supports 802.1p, as well as IP TOS and DSCP, by which you

can configure the port-based priority when the terminal does not support the above

trhee configurations, and different priority for the ports is wanted. This configuration

can only affect the packets without priority in the port. SICOM3024SM supports four

class of priority.

Port T runking

In SICOM3024SM, multiple physical ports can be aggregated into one logic port,

which has the same rate, duplex and VLAN ID. Port Trunking can be configured in one

single switch for max 4 ports. In this way, the pressure of network traffic is reduced.

Port Mirroring

The data of one port can be mapped to another port for user to real-time monitor the

SICOM3024SM Industrial Ethernet Switch User Manual

- 8 -

communication.

Configure Port Working Modes

SICOM3024SM is able to configure the working mode of all ports through

management: full/half duplex adaptive, 10M/half duplex, 100M/half duplex, 10M/full

duplex, 100M/full duplex, etc.

Configure Port Traffic Flow

You can configure the TX and RX rate of all ports via the management software of

SICOM3024SM. For port of 100Mbps, it can be set as 128K、256K、512K、1M、2M、

10M、50M、100M. For Gigabit port, it can be set as 100M、500M、1000M.

Static Multicasting Communication

You can add multicasting users by adding static multicasting table manually. Compared

to dynamic multicasting, it is more simple, reliable and faster without protocols. You

can forward the multicasting data by configuring static multicasting forwarding tables.

Users can manually configure the multicasting communication according to their needs.

Static multicasting can not be used together with IGMP simultaneously.

IGMP

IGMP is Internet Group Multicast Protocol. SICOM3024SM series offers IGMP

monitor and query functions. Data packets can be transmitted to multiple necessary

host computers to prevent overloading. This solves the problems of occupied

bandwidth when broadcasting.

Broadcasting Storm Control

SICOM3024SM series offers broadcast storm protection ensuring the smooth

communication platform of the switch network. The switch will filter out the over flow

once the bandwidth of broadcast flow exceed the limit.

DT-Ring

DT-Ring is specially designed and developed by Kyland. It determines the state of ring

& port and ensures the redundant network won’t form ring by inspecting the ring port

state and less protocol messages. It make sure the Ethernet redundant ring is fast and

reliable to meet the high requirements of industrial communications.

DT-Ring+

Chapter 2 Performance Specifications

- 9 -

Based on DT-Ring, DT-Ring+ realizes standby between two rings and determines the

ring and port state according to the standby device ID ensuring the redundant network

does not form ring.

RSTP

RSTP and STP offer network redundancy protection for the switch network. RSTP can

realize all the functions of STP, and additional reduce the delay from block to forward,

resuming the network ASAP.

ACL

SICOM3024SM offers ACL（Access Control List） function to define the access rules

by using the protocols of source or object MAC addresses. It can limit the network

traffic, increases the networking performance and control the communication flow.

Alarm Output

Alarm is significant when it is used for real-time transmission of device alarm output.

SICOM3024SM offers the alarming functions for port and ring. Through management

software, all the alarming functions can be enabled or disabled. The alarming

information is shown from management interface.

SNMP

SNMP（Simple Network Management Protocol）offers frame structure for low

level network management. SNMP protocol is used so widely that many kinds of

networking devices, software and system employ it. It is easy to realize, open and free,

and can be used to control various devices.

RMON

RMON is a standard monitoring regulation to switch the network monitoring data

between network monitor and console system. It offers more selections for network

operator to use the suitable console and network monitor for special requirements. It is

also the expansion to SNMP functions and is specially useful for monitoring and

managing LAN. The purpose of developing RMON is to provide statistic result of

information flow and analyze network parameters so as to work out a comprehensive

diagnoses, plan and regulation.

By RMON, you can operate among multiple manufacturers for SNMP management

and monitoring agent. What’s more, it can offer a standard for a group of MIB to

SICOM3024SM Industrial Ethernet Switch User Manual

- 10 -

collect the network statistics which is not available via SNMP. RMON realizes

previous network diagnoses by using powerful alarm group, it allows that a domain

value is set for critical parameters so as to automatically send alarm signal to manager

control center.

POE function

SICOM3024SM support POE function. SICOM3024SM- POE board can be used as an

independent module group. It supports max 6 FE ports with POE function. Each FE

port is compliant with the power supply of IEEE802.3af standard. The module group

can work under 24V and 48V.

Chapter 3 Hardware Structure

- 11 -

Chapter 3 Hardware Structure

3.1 System Structure

SICOM3024SM hardware is structured as Figure3-1:

Figure 3-1 Hardware Structure

System hardware mainly consist the following parts:

1． Switching network controller employs ASIC chip technology, offering layer-2

wire-speed transfer of data packets.

2．Integrated module of transmitting and receiving for fiber interfaces.

3．Industrial power supply with protection of over-current, over-voltage and EMC.

4．EMC protection for all RJ45 ports.

3.2 Switch Structure

3.2.1 Case

SICOM3024SM case is 19inches 2U stable rack mounting type structure. The entire unit

has a six-side-enclosed structure, with protection class up to IP40. The case’s top side

plates made of ribbed aluminum profile are a part of the heat dispersion system of the

SICOM3024SM Industrial Ethernet Switch User Manual

- 12 -

entire unit. The single-ribbed structure can double heat dissipation area. The heat

generated when the unit is working is effectively dissipated into the environment via the

ribbed heat-dissipation surface in the form of radiation and convection greatly increasing

the high temperature resistance of equipment. Discarding the traditional form of axial

fan heat dispersion reduces power consumption of the entire unit and increases the

stability of the system. The figuration of SICOM3024SM case is shown in Figure 3-2.

Its contour dimension is 88 ㎜×482.6 ㎜×245 ㎜（height×width×thickness）

Figure 3-2 outline drawing of SICOM3024SM

Warning:

The shell of this switch is a part of the heat dissipation system of the unit. It may get

hot during working, so never touch the shell when the equipment is working to avoid

burning.

3.2.2 Front Panel

SICOM3024SM Industrial Ethernet switch front panel is show as Figure 3-3：

Chapter 3 Hardware Structure

- 13 -

Industrial Ethernet Switch

SICOM3024SM

G4G2G1

RUN

13109 11 1287

DPX LINK

54 6213

slot1 slot2

17 181615

LINK/ACT

10M/100M

2321 22 2419 20

slot3 slot4

indicators for Gigabit

ports

operation indicator

indicators for 100M

ports

Figure 3-3 Front panel of SICOM3024SM

3.2.3 Back panel

SICOM3024SM Industrial Ethernet switch front panel is show as Figure 3-4

CONSOLE

G1 G4G2 G3

POWER

OFF

AC/DC220V

21 534 6

RJ45 ports

SFP module

RS232 console ports

9.5mm-POE power input terminal

AC power input terminal

AC power

switch

Figure 3-4 Back panel of SICOM3024SM

SFP Gigabit Optical Fiber/TP interface

SICOM3024SM offers four pairs of redundant 1000Base-LX full duplex single mode

or multi-mode optical fiber interface (LC connector), or 1000Base-TX RJ45 interface

（RJ45 connector）Port numbers are G1,G2, G3and G4. Optical fiber interface should

be used in pairs (TX and RX are a pair), TX interface is the transmitting end connected

to the receiving end RX of the optical fiber interface of another remote switch; RX is

the receiving end connected to the transmitting end TX of the same optical fiber

interface of the same remote switch. Four pairs of redundant 1000Base-LX optical fiber

interface can be used to form an optical fiber redundant ring network. In the event of

the system fault, the recovery time of the redundant ring network is less than 50ms,

effectively increasing the reliability of network operation.

SICOM3024SM Industrial Ethernet Switch User Manual

- 14 -

Figure 3-5 SFP Plug and Play unit

Gigabit SFP FX/TX Plug and play steps：Figure3-6

Insert SFP unit:

z There are two breaks on Fiber-port (LC) and one break on Ethernet port (RJ45)

of SFP unit.

z Insert the SFP into case backward to the PCB board. The position is right

when you hear a sound. Ready for use if the SFP handle horizontal with

connector.

Pull SFP unit:

z The fiber part could be pulled out from SFP case when angle 90 degree

between handle of SFP unit and connector.

z Pull out the fiber part from case

Figure 3-6 SFP Process for Plug and Play

Chapter 3 Hardware Structure

- 15 -

Optical Fiber interface

SICOM3024SM offers 1 to 24 pairs of redundant 100Base-FX full duplex single mode or

multi-mode optical fiber interface, with SC, FC and ST connector. Optical fiber interface

should be used in pairs (TX and RX are a pair). TX interface is the transmitting end

connected to the receiving end RX of the optical fiber interface of another remote switch;

RX is the receiving end connected to the transmitting end TX of the same optical fiber

interface of the same remote switch. Eight pairs of redundant 100Base-FX optical fiber

interface can be used to form an optical fiber redundant ring network. In the event of the

system fault, the recovery time of the redundant ring network is less than 50ms,

effectively increasing the reliability of network operation.

RJ45 interface

SICOM3024SM offers 1 to 24 10Base-T/100Base-TX RJ45 Ethernet ports. Each RJ45

port has self-adaptation function, support MDI/MDI-X auto-connection and can be

connected to end equipments, servers, hubs or other switches in straight-through or

cross-over way. Each port supports IEEE802.3x self-adaptation, so the most suitable

transmission mode (half duplex or full duplex) and data rate (10 Mbps or 100Mbps) can

be automatically selected (the connected equipment should also support this

characteristic). If the equipment connected to these port does not support self-adaptation,

the ports will be able to send at proper speed but transmission mode is defaulted as half

duplex.

POE Interface

SICOM3024SM has 1 to 24 RJ45 ports of 10Base-T/100Base-TX with POE function.

Each RJ45 port supports feeding output of DC24V and DC48V and provides maximum

current of 600mA to remote Ethernet devices or industrial Ethernet switch at the power

receiving end. The maximum power consumption of port is configured to 5W, 10W and

15W through the network management. Each RJ45 port supports self-adaptive function

and MDI/MDI-X auto-connection.

LED Indicators

The indicators on the front panel of SICOM3024SM can show system operation and port

status, helping detect and eliminate faults. Table 3-1 describes the meanings of all

indication lights on the front panel.

Table 3-1 descriptions for LED indicators

SICOM3024SM Industrial Ethernet Switch User Manual

- 16 -

LED Condition State

System state LED

Blinking

1Hz

Switch operates normally

RUN

OFF Switch not operate

Gigabit Optical fiber interface state LED（optical fiber interface G1、G2、G3、G4）

DXP On

Effective network connection has been established for the

port.

LINK Blinking Network activities are available for the port.

Ethernet RJ45 port state LED

Each RJ45 Ethernet port has two indicators, a yellow lamp and a green lamp. The yellow

lamp indicates port speed, and the green lamp indicates port link state.

100M working status（i.e. 100Base-TX）

10M/100M

(Yellow)

Off

10M working status (i.e. 10Base-T）

Effective network connection has been established for the

port

Blinking Network activities are available at the port

LINK/ACT

（Green）

Off

No effective network connection has been established for the

port.

DC Power input terminal

DC24V or DC48V: multi-strand wires of more than 0.75 mm are used for power

connection. Connection sequence is shown in Figure 3-7. Connection and mounting

procedures are as follows:

1． Strip 5mm-long sheath from power cable and twist the bare copper wires together

into a bundle;

2. Use a 2.5 ㎜ one-slot screwdriver to unscrew the “power cable locking screw”,

insert the power cable into the hole at the terminal tail, and screw down the “power

cable locking screw”;

3． Insert the power terminal into the DC power socket of the equipment and use a

2.5mm one-slot screwdriver to screw down the two “terminal locking screws” to

firmly connect the terminal with the power connector.

Chapter 3 Hardware Structure

- 17 -

+24V

terminal locking screws

power ground

protection ground

Locking screws for power cables

Figure 3-7 DC Power connection

AC Power input terminal：

AC220V: Single-phase three cores wire is used to for power connection. The terminal

integrates a fuse socket which is convenient to fix new AC power fuse. Steps of

replacing fuse are as follows:

1. Pull-out fuse holder from the AC power outlet as shown in Figure 3-8a. Push a 2A

fuse into the holder, and also can put a standby fuse into spare slot.

2. As shown in Figure 3-8b, insert the fuse holder into AC power outlet.

Figure 3-8a STEP 1

SICOM3024SM Industrial Ethernet Switch User Manual

- 18 -

Figure 3-8b STEP 2

POE Power input terminal (9.5mm)

The terminal of POE power input is 5 cores terminal (as Figure 3-9). 1 and 2 are positive

poles, 3 and 4 are negative poles, 5 is for grounding protection. Using POE should

connect power into the 5 cores terminal. RJ45 ports connect PD. The procedures of

5-core terminal power connection refer to the DC power input terminal connection.

+-+-

Figure 3-9 9.5mm POE power input terminal

RS232 Network management interface（CONSOLE）

The network management interface of SICOM3024SM is shielded RJ45 connector and

its interface communication standard is 3-wire RS232. Users can use a network

management cable with end bearing RJ45 plug and another end DB9F plug to connect

the network management interface of SICOM3024SM with the 9-pin serial port of the

control computer. Operating the local management software to set up SICOM3024SM

by CLI. The wiring sequence for network management interface of SICOM3024SM and

the 9-pin serial port of PC computer is shown in Figure 3-10.

Chapter 3 Hardware Structure

- 19 -

Figure 3-10 CONSOLE wiring diagram

Grounding

SICOM3024SM Series Industrial Ethernet switch has a grounding screw hole in the rear

panel. After connecting one terminal of grounding wire with the cold-pressing terminal,

insert it to the grounding hole and screw it down with grounding screws. The other

terminal of grounding wire connects to the ground. The section of grounding wire is not

less than 2.5 ㎜

Chapter 4 Hardware Installation

- 21 -

Chapter 4 Hardware Installation

4.1 Installation requirement

As a monomer structure switch, it can be fixed on standard 19’ rack. Before installation,

make sure all condition match the installation requirement.

1. Power supply: DC24V、DC48V、DC110V、AC220V、DC220V. Please pay attention

to voltage level.

2. Environment: -40℃～75℃ Relative humidity: 5％～95% (non-condensing)

3. Earth resistance: <5Ω

4. Make sure all fiber cables and connectors are ready for use

5. Avoid sunshine, and strong EMC area

6. 19 inches rack is ready for SICOM3024SM

7. Check if you have all necessary cables and connectors.

4.2 Mainframe installation

4.2.1 Stable rack mounting

SICOM3024SM industrial Ethernet switch can be installed in any standard 19 Inch Rack.

Before mounting; make sure the following is ready:

1．Make sure there is enough space on the rack for SICOM3024SM installation

2．The power supply is available for SICOM3024SM.

After selecting the mounting location, fix the SICOM3024SM with four screws

(M5×14)

SICOM3024SM Industrial Ethernet Switch User Manual

- 22 -

Figure 4-1 SICOM3024SM mounting drawing

Cable wiring should meet the following requirements:

1． Before wiring, check whether the specifications, models and quantities of all

cables comply with the construction drawing design and contract requirements.

2． Before cable wiring, it is necessary to check whether there is damaged cable

and whether the cables are accompanied by ex-factory records and vouchers

attesting their quality such as quality assurance certificate etc.

3． The specifications, quantities, route directions and laying position of the

cables to be laid should meet the design requirements of construction drawings.

The laying length of each cable should be determined according to its actual

position.

4． No intermediate break or joint is allowed for the cables to be laid.

5． User’s cables and power cable should be laid separately.

6． Inside walkways, the cables should be properly arranged in good order, with

uniform, smooth and flat turnings.

7． Cables should be straightly laid in cable channels. Extruding of cable from

cable channels to block other outlet or inlet holes is not allowed. The cables at

Chapter 4 Hardware Installation

- 23 -

the outlet part of cable channel or at turnings should be bundled and fixed.

8． If cables, power line and grounding conductor are laid in the same channel,

cables, power line and grounding conductor should be not folded or blended

together. If a cable line is overly long, coil and place it in the middle of the

cabling rack, do not let it cover on other cables.

9． When laying the pigtail, avoid knotting of optical fiber cable, minimize the

amount of turnings and avoid turnings with overly small radius. Bundle

pigtails in proper tightness and avoid too tightly bundling. If laid on a cabling

rack, it should be placed separately from other cables.

10. There must be the relevant marks at both ends of cable and the information on

the marks should be explicit to facilitate maintenance

Attention: When laying pigtails, prevent optical fiber cable from knotting, minimize the

amount of turnings and avoid turnings with too small radius, because turning with too small radius

will result in serious consumption of optical signal of links, affecting communication quality.

Chapter 5 Test methods

5.1 Self inspection

When electrify the equipment, all service indicator lights will flash one time, After 30

seconds, the RUN indicator will keep flashing, showing the devices work well.

5.2 TP Port Test

As shown in Figure 5-1, SICOM3024SM is powered on, connecting any two RJ45 ports

to two PCs by straight-through cable and send Ping command to each other, they can

both get command from each other without packet loss, The yellow light of the port

should be always on (PC work on 100M) or always off (PC work on 10M), the green

light should be blinking. In the same way, test all other RJ45 ports (Operations on PING

command is shown as the following example).

PC1

PC2

Figure 5-1 TP port test

5.3 POE Port Test

As shown in Figure 5-2, SICOM3024SM is powered on, connecting any two RJ45 ports

to uplink Ethernet ports of PD at two sides by cross-over or straight-through cable, and

connecting any RJ45 port of PD at two sides to the test computer, sending Ping

command to each other, they can both get command from each other without packet loss,

The corresponding yellow light of the port is always on, the corresponding green light is

blinking, showing the testing RJ45 ports run well. In the same way, test all other RJ45

SICOM3024SM Industrial Ethernet Switch User Manual

ports (Operations on PING command is shown as the following example).

PC1

PC2

PD1

PD2

Figure 5-2 POE port test

5.4 Fiber Port Test

As shown in Figure 5-3, two units of SICOM3024SM are connected to fiber chain

network, connecting any one RJ45 port in each device to PCs by straight-through cable

and sending Ping command to each other. They can both get command from each other

without packet loss, and the LINK/ACT light of the fiber port should be always on.,

showing the testing fiber ports work well. In the same way, test another pair of fiber

ports. (Operations on PING command is shown as the following example).

Chapter 5 Test methods

Figure 5-3 Fiber port test

PING commands example：

Suppose the IP address for one computer is. 192.168.100.10 and the other one is

192.168.100.11, operate the “begin” menu on the one computer, and select the:

operation” item. input “cmd” or ”command”, sending Ping 192.168.100.11 –l 1000

-t，operate the “begin” menu on the second computer, and select the: operation” item.

input “cmd” or ”command”, sending ping 192.168.100.10 –l 1000 –t. return

“Reply from 192.168.100.11：bytes=1000 time<10ms TTL=128”,for the second

computer, Return “ Reply from 192.168.100.10 ： bytes=1000 time<10ms

TTL=128”,after ten minutes for operating ,use CTL+C command to Stat. the missing

rate. If the missing rate is “0” shows the equipment are in good condition

Chapter 6 Networking and Configurations

- 29 -

Chapter 6 Networking and Configurations

6.1 Networking

SICOM3024SM industrial Ethernet switch provides one to twenty-four

10Base-T/100Base-TX Ethernet RJ45 ports, each of which can provide link directly to

the terminal devices, or to another industrial Ethernet switch/hub before terminal device

as link share. SICOM3024SM has four (4) pairs of redundant fiber ports of 100Base-LX

single mode or multimode. The redundant Gigabit fiber ports can form backbone

redundant fiber ring of 1000M with recovery time less than 50ms. Furthermore,

SICOM3024SM supply maximum 24 pairs of redundant fiber port of

100Base-FX-SM/MM or RJ45 ports, which can form 100M redundant ring network with

the recovery time less than 50ms. It is widely used in electric power, transportation,

energy, water treatment and factory automation etc.

The typical networking topology of SICOM3024SM is redundant ring network.

SICOM3024SM can form the redundant fiber ring network as shown in Figure 6-1, in

which one device is set as master and the rest are slave. The network can re-configure

within 50ms when failure occurs.

Figure 6-1 SICOM3024SM build the redundancy fiber ring

6.2 System configure

SICOM3024SM is a integrative industrial Ethernet switch, offering the system main

board, power supply, backplane, 4 self-adaptive SFP interfaces of 100/1000M, 4

SICOM3024SM Industrial Ethernet Switch User Manual

- 30 -

expansion slots which can connect to plug and play module of 100M. Each of the four

100M modules (plug and play) offer 6 ports, which can be RJ45 ports of

10Base-T/100Base-TX with POE function or 100M single mode/multimode fiber ports.

The power supply for SICOM3024SM should be DC24V、DC48V、DC110V、AC220V、

DC220V. Detailed configuration showing as table 6-1

Table 6-1 SICOM3024 configure table

Model Description

SICOM3024SM-4GX 4 expansion slots, up to 24 × 100M ports,battery feed input

SM3-6S(M) 6 × 100Base-FX-SM/MM fiber ports (FC/SC/ST)

SM3-5S(M)-1TX 5× 100Base-FX-SM/MM fiber ports (FC/SC/ST)

1× 10Base-T/100Base-TX RJ45 port

SM3-4S(M)-2TX 4 × 100Base-FX-SM/MM fiber ports (FC/SC/ST)

2 × 10Base-T/100Base-TX RJ45 ports

SM3-3S(M)-3TX 3 × 100Base-FX-SM/MM fiber ports (FC/SC/ST)

3 × 10Base-T/100Base-TX RJ45 ports

SM3-2S(M)-4 TX 2 × 100Base-FX-SM/MM fiber ports (FC/SC/ST)

4 × 10Base-T/100Base-TX RJ45 ports

SM3-S(M)-5TX 1 × 100Base-FX-SM/MM fiber port (FC/SC/ST)

5 × 10Base-T/100Base-TX RJ45 ports

SM3-6TX 6 × 10Base-T/100Base-TX RJ45 ports

SM3-6TX-PSE-24V 6 × 10Base-T/100Base-TX RJ45 ports

Support POE, feeding output of 24V, 12W

SM3-6TX-PSE-48V 6 × 10Base-T/100Base-TX RJ45 ports

Support POE, feeding output of 48V, 12W

Chapter 7 WEB Management

- 31 -

Chapter 7 WEB Management

SICOM3024SM support WEB page management, through web page, you can monitor

the working state of the switch, and configure and upgrade the switch online.

7.1 Login W eb Page

Connecting the SICOM3024SM switch with a computer, input the IP address, eg.

“192.168.0.2” in the IE browser, a window will appear as Figure 7-1, the default user

name and password are admin and 123.click “OK” to enter.

Figure 7-1 Login Page

The main page is as Figure 7-2

At the left of the page is the management tree menu including device state, basic

configuration, advanced configuration, device management, save all changes, restore

default settings and so on. , each menu may include some submenu.

SICOM3024SM Industrial Ethernet Switch User Manual

- 32 -

Figure 7-2 Main Page

7.2 Device Status Display

The menu of device status includes three submenus: Basic Information; Port state, Port

Traffic Flow.

7.2.1 Basic Info

Click “Basic info” and enter the interface as shown in Figure 7-3, which displays MAC

address, IP address, software version, hardware version etc

Figure 7-3 Basic Info

Chapter 7 WEB Management

- 33 -

7.2.2 Port State

Click “Port State” and enter the page as shown in Figure 7-4, which displays the link

state, port speed, full/half duplex and flow control state etc.

Figure 7-4 Port State

7.2.3 Port Traffic Flow

Click “Port Flow” and enter the page as shown in Figure 7-5 which displays the port

flow statistics of each port.

SICOM3024SM Industrial Ethernet Switch User Manual

- 34 -

Figure 7-5 Port Flow

7.3 Device Basic Configuration

In the menu of “Device Basic Configuration”, there are functions to configure IP address,

device name, port, to change password, query software version and upgrade software,

upload and download configuration, etc.

7.3.1 Configure IP Address

Click the “IP address” in the left menu and enter the page (as Figure 7-6), where you can

modify IP address, subnet mask and gateway with click on “Apply” button. To make the

modification take effect, you need to restart the switch.

Chapter 7 WEB Management

- 35 -

Figure 7-6 Configure IP Address

7.3.2 Configure Device Name

Click the “Device Name” in the left menu and enter the page (as Figure 7-7), fill in the

device name and click “Apply” button.

Figure 7-7 Configure Device Name

7.3.3 Port Configuration

Click the “Port Configuration” in the left menu and enter the page (as Figure 7-8), where

you can configure port state (enable/disable), auto-negotiation (enable/disable), port

speed (10/100M), duplex (full/half), flow control (open/close). After configuration, click

“Apply” to make it take effect.

SICOM3024SM Industrial Ethernet Switch User Manual

- 36 -

Figure 7-8 Port Configuration

7.3.4 Change Password

Click the “Change Password” in the left menu and enter the page (as Figure 7-9), enter

old password and new password, click “Apply” to take effect.

Figure 7-9 Change Password

7.3.5 Upgrade Software

Click the “Upgrade Software” in the left menu and enter the page (as Figure 7-10). For

Chapter 7 WEB Management

- 37 -

detailed upgrading instructions, please refer to the Appendix D.

z Enter the main WEB page, click “upgrading bar” of basic configuration in

navigation bar to enter into the upgrading page as shown in the following Figure:

Figure 7-10 Upgrade Software

z Configure IP address, user name, password and software name of the FTP server,

click “Apply” button and record upgraded software ID. As figure 7-10, the address of FTP server and IP address of switch should be in the same network segment.

z Wait for upgrading and see the successful message. z Click “Software Version” in navigation bar, set the software ID as startup version

and click “OK” as shown in the Figure 7-11 of software version.

z Click “reset” in the navigation bar and click “reset” z Wait for 30 seconds to start up network management system. Click “Device

Basic Info”, check software version to confirm if it is upgraded successfully.

7.3.6 Software V ersion

Click the “Software Version” in the left menu and enter the page (as Figure 7-11), which

displays two versions: one is startup and another is closed. This function is for the

purpose of upgrading software.

Figure 7-11 Software Version

SICOM3024SM Industrial Ethernet Switch User Manual

- 38 -

7.3.7 Configure upload and download

Click the “Upload/Download Configuration” in the left menu and enter the page (as Figure

7-12), enter server IP address and file name to be uploaded/downloaded, user name, password

and click “Apply” to take effect. See the details of FTP configurations in “Appendix D”.

z Select “upload” or “download” file and set FTP server IP address, file name, user

name, password and file name to be upgraded, click “Apply” as shown in Figure

7-12. FTP server address and IP address of switch should be in the same segment.

z After clicking “Apply”, upload or download successfully.

Figure 7-12 Upload & Download Configuration

Figure 7-13 Upload sample

7.4 Device Advanced Configuration

The advanced configurations include port traffic flow, VLAN, port mirroring, port

trunking, static multicasting address, IGMP Snooping, SNMP, Alarm, ACL, RSTP,

DT-Ring, POE, QoS and other settings etc.

Chapter 7 WEB Management

- 39 -

7.4.1 Port Traffic Flow

Click the “Port Flow” in the left menu and enter the page (as Figure 7-14), where you

can configure the RX/TX speed of each port as the range of 128K、256K、512K、1M、

2M、10M、50M、100M for 100Mbps port and 100M、500M、1000M for Gigabit port.

Click “Apply” to finish configuration.

Figure 7-14 Port Traffic Flow

7.4.2 VLAN

Click the “VLAN” in the left menu and enter the page (as Figure 7-15) and select “based

on 802.1Q” as VLAN mode, click “Add” to enter into the page as Figure 7-16. Enter

VLAN name, ID(VLAN1 is the default), select VLAN member, tag or untag, click

“Apply” to finish configuration.

Note: in the default state, VLAN ID is “1”, the range of ID no. is from 2 to 4093.

SICOM3024SM Industrial Ethernet Switch User Manual

- 40 -

Figure 7-15 Add VLAN

Figure 7-16 VLAN Configuration

Figure 7-17 VLAN configuration successfully

Chapter 7 WEB Management

- 41 -

Figure 7-18 Untagged Port VLAN List

7.4.3 Port Mirroring

Click the “Port Mirroring” in the left menu and enter the page (as Figure 7-19), select

mirroring port from range of Module1-4/FE1~FE6、Module0/ GE1~GE4 and mirrored

port from the range of TX、RX、TX&RX, click “Apply” to finish configuration.

Figure 7-19 Port Mirroring

SICOM3024SM Industrial Ethernet Switch User Manual

- 42 -

Figure 7-20 Port Mirrored

7.4.4 Port Trunking

Click the “Port Trunking” in the left menu and enter the page (as Figure 7-21), six trunk

groups are supported. Each group allows max 4 ports. Choose the port from the froup,

and Click

、 , to add or delete trunked port. Click “Apply” to finish configuration.

See the sample at figure 7-22,

Figure 7-21 add trunking group

Note:

G1-G4can be in one trunk group independently, but can not be in one group with

ports of 100Mpbs. The ports on the same VLAN can be trunked

Chapter 7 WEB Management

- 43 -

Figure 7-22 Port trunking sample

7.4.5 Static Multicasting Address Table

Click the “Static FDB Multicasting” in the left menu and enter the page (as Figure 7-23),

select “enabled” and click “Apply”, Add static multicasting MAC address, VLAN ID and

select port as shown in Figure 7-24, click “Apply”. When it is finished, click the “Static

Multicasting Address Table” in left menu, and see figure 7-25. To configure the

multicasting address, click Add and reset MAC address. To delete the mutlcasting

address, select the serial No. and delete.

Note: Before enabling static multicasting address table, “IGMP Snooping” must be

closed firstly.

SICOM3024SM Industrial Ethernet Switch User Manual

- 44 -

Figure 7-23 Static Multicast address table

Figure 7-24 Static Multicast filling sample

Chapter 7 WEB Management

- 45 -

Figure 7-25 Static Multicast configure successfully

7.4.6 IGMP-snooping

Click the “IGMP-Snooping” in the left menu and enter the page (as Figure 7-26), enable

IGMP-SNOOPING and auto query, click “Apply” to finish configuration. Click

“IGMP-Snooping” in the left menu again to show configuration result as Figure 7-27.

Note: Before enabling IGMP Snooping, static multicasting address table must be

closed firstly. The switch only support 256 pieces of multicast address, never

over this range during the operation.

SICOM3024SM Industrial Ethernet Switch User Manual

- 46 -

Figure 7-26 IGMP-SNOOPING

Figure 7-27 IGMP Snooping configure successfully

7.4.7 SNMP Configuration

Click the “SNMP Configuration” in the left menu and enter the page (as Figure 7-28),

enable SNMP and set read/read&write name, enter TRAP server IP address, TRAP port

no. and click “Apply” to finish configuration.

By SNMP configuration, the device only receive the message which name is line with the

setting name of read and read&write;

By setting the Trap IP address, device can selectively transmit TRAP message to those IP

addresses in the Trap IP address table;

By setting the Trap port number, EMS management server just receives TRAP messages

on those port numbers.

Chapter 7 WEB Management

- 47 -

Figure 7-28 SNMP configuration

7.4.8 Alarm configuration

Click the “Port Alarm” in the left menu and enter the page (as Figure 7-29) to configure

port and ring alarm, click “Apply” to take it effect.

SICOM3024SM Industrial Ethernet Switch User Manual

- 48 -

Figure 7-29 Ring Alarm Configuration

7.4.9 ACL Configuration

Click the “ACL Configuration” in the left menu and enter the page (as Figure 7-30),

click “port configuration” and enter the page (as Figure 7-31), choose “anble/disable”

for all ports, click “apply” to finish port status configuration. Click “Add List” from

Figure 7-30, enter the page as Figure 7-32, select “Group number”, “Item number”,

“Action” and “Control port”; fill out the items: “Source MAC”, “Destination MAC”,

“Ethernet Type”, “Vlan Tag”; click “apply” to finish configuration.

Figure 7-30 IP ACL

Chapter 7 WEB Management

- 49 -

Figure 7-31 Port state configuration

Figure 7-32 ACL protocol configuration

7.4.10 RSTP Configuration

Click the “RSTP” in the left menu and enter the page (as Figure 7-33), select “RSTP” or

“STP” to configure; fill out in the items “Spanning Tree Priority” (From 0 to 65535. The

default is 32768 with the step of 4096), “Hello Time” (from 1 to 10. The default is 2),

“Max Age Time” (From 6 to 40. The default is 20), “Forward Delay Time” (From 4 to 30.

The default is 15) and “Message-age inc” (default or compulsion). Additionally, you can

configure protocol state of each port, priority, path cost etc. After configuration, click

SICOM3024SM Industrial Ethernet Switch User Manual

- 50 -

“apply”.

Figure 7-33 RSTP configuration

7.4.11 DT-Ring Configuration

Click the “DT-Ring” in the left menu and enter the page (as Figure 7-34) to configure

redundant ring based on port or VLAN. Click “Add” to enter page (such as Figure 7-35

and Figure 7-36). Enter domain ID No. (ID=1~32）, domain name, set master or slave

station, select ring port (Module 1-4/FE1~FE6, 0/GE1~GE4). Additionally, there is

DT-Ring+ in this device, you can select this function and enable it, select standby port

and click “Apply”. Click ring name and see ring state in the DT-Ring page as Figure

7-37, see it as Figure 7-36.

Attention：

Each ring only support one master, the others are slaves. The devices in one ring

have the same ring ID. The port with different ID No. can’t be in one ring network.

Redundant ring support DT-Ring. You can only configure ring based on port or

VLAN. One of ports on the master is in block state, the other is in transfer state. If

the port for transferring is blocked, the port in blocking state can be used as

Note: RSTP can not be used together with DT-Ring.

Chapter 7 WEB Management

- 51 -

transferring port with the recovery time less than 50m.

Configure four switches connecting by DT-Ring+: there are only two standby ports

in two rings. The two standby ports are chosen from one ring.

Figure 7-34 DT-Ring

Figure 7-35 DT-Ring configuration based on VLAN

SICOM3024SM Industrial Ethernet Switch User Manual

- 52 -

Figure 7-36 DT-Ring configuration based on ports

Chapter 7 WEB Management

- 53 -

Figure 7-37 DT-Ring configuration successfully

7.4.12 POE Configuration

Click the “POE Configuration” in the left menu and enter the page (as Figure 7-38),

select “Enable” or “Disable” for all ports. In the “Enable” state, POE function can work.

The output power consumption is 5W, 10W and 15W, which can be chosen according to

the power consumption of PD. Support function of voltage detection. Under the Enable

state of voltage detection, the power is automatically disconnected when the voltage

lowers than 22V or 28V. Web page shows output current, voltage, power consumption,

etc.

SICOM3024SM Industrial Ethernet Switch User Manual

- 54 -

Figure 7-38 POE configuration

7.4.13 QoS Configuration

Click the “QOS Configuration” in the left menu and enter the page (as Figure 7-39),

enable QoS: weight (WRR) and preemption mode. Priority based on 802.1P or IO TOS,

DSCP and port are for options. The priority based on 802.1p and IP TOS/DIFF can be

used at the same time and they can not be used together with priority based on port.

Attention：

There are two classes for priority based on port and four queues for others.

Chapter 7 WEB Management

- 55 -

Figure 7-39 Qos configuration

Click “802.1P Priority” and enter the page as figure 7-40. There are total 8 classes for

802.1P. SICOM3024SM supports four classes. You can select it and click “Apply”.

Figure 7-40 802.1P priority configuration

SICOM3024SM Industrial Ethernet Switch User Manual

- 56 -

Click “IPTOS Priority” and enter the page as figure 7-41. There are total 8 classes for

IPTOS. SICOM3024SM supports four of them. You can select it and click “Apply”.

Figure 7-41 IPTOS priority configuration

Click “DSCP Priority” and enter the page as figure 7-42. There are total 64 classes for

DSCP. SICOM3024SM supports four of them. You can select it and click “Apply”.

Chapter 7 WEB Management

- 57 -

Figure 7-42 DSCP Priority configuration

7.4.14 Other configuration

Click the “Other Configurations” in the left menu and enter the page (as Figure 7-43),

which include two configurations of broadcasting storm control and MAC aging time.

There are totally five options for broadcasting storm control: disable、1/2、 1/4、1/8、

1/16、1/32. When the broadcasting packets occupy 1/2、1/4、1/8、1/16、1/32 of bandwidth,

the packet are dropped. Disable state won’t control the broadcasting messages. MAC

address aging time is selected from 10-3600sec and 300sec is selected normally. Click

“Apply” to finish.

SICOM3024SM Industrial Ethernet Switch User Manual

- 58 -

Figure 7-43 Other configuration

7.4.15 RMON Configuration

RMON configurations include statistics, history, Alarm and Event.

7.4.15.1 RMON statistics

Click “RMON Statistics” in the left menu to configure as figure 7-44. Enter index

no.(from 1-65535) , owner serial no. (1-32), and select port no. (ifindex.0/1-4,1/1-6,

2/1-6, 3/1-6, 4/1-6). Click “Apply” to finish.

Figure 7-44 RMON Statistics configuration

7.4.15.2 RMON history

Click “RMON History” in the left menu to configure as figure 7-45. Enter index no.

(From 1-65535), owner serial no. (1-32), and select port no. (ifindex.0/1-4, 1/1-6, 2/1-6,

3/1-6, 4/1-6), sampling no. (1-65535, default number is 50), and sampling interval

(1-3600, default number is 1800). Click “Apply” to finish.

Chapter 7 WEB Management

- 59 -

Figure 7-45 RMON History Configuration

7.4.15.3 RMON Alarm

Click “RMON Alarm” in the left menu to configure as figure 7-46. Select alarm node in

the MIB list and double click, the OID will finish automatically. In this page, enter index

no.(from 1-65535) , owner serial no. (1-32), and select port no. (ifindex.0/1-4,1/1-6,

2/1-6, 3/1-6, 4/1-6), sampling type( absolute/ delta), alarm type (rising alarm/ falling

alarm/ rise or fall alarm), sampling interval (1-65535), rising threshold value(1-65535),

falling threshold value(1-65535), rising event index(1-65535) and falling event

index(1-65535). Click “Apply” to finish.

SICOM3024SM Industrial Ethernet Switch User Manual

- 60 -

Figure 7-46 RMON Alarm configuration

7.4.15.4 RMON Event

Click “RMON Event” in the left menu to configure as figure 7-47. Enter index no.(from

1-65535) , owner serial no. (1-32), event type (LOG/SNMP-trap/Log-and-Trap), event

description (1-127), and event group (1-127). Click “Apply” to finish.

Chapter 7 WEB Management

- 61 -

Figure 7-47 RMON Event configuration

7.5 Device Management

Device Management includes reset, logout.

7.5.1 Restart

Click “Reboot” in the left menu and enter the page as figure 7-48. Click “Reboot” to

reset the device.

Figure 7-48 Reboot

7.5.2 Logout

Click “Logout” in the left menu and enter the page as figure 7-49. Click “Logout” to

exit.

Figure 7-49 Logout

7.6 Configurations

Click “Save Configurations” in the left menu and enter the page as figure 7-50. Click

“Save” to save all settings.

Figure 7-50 Save Configurations

SICOM3024SM Industrial Ethernet Switch User Manual

- 62 -

7.7 Load Default

Click “Load Default ” in the left menu and enter the page as figure 7-51. Click “Load

Default” to restore all default settings.

Figure 7-51 Load Default

Appendix A Twisted-pair and Pin Distribution

- 63 -

Appendix A Twisted-pair and Pin Distribution

For the connection of 10Base-T/100Base-TX, the twisted-pair must have two pair cable.

Each pair is distinguished with two different colors. For example, one strand is green,

and the other is the alternate of green and white stripes. RJ-45 connector should be

equipped at both ends of the cable.

Fig. A-1 Shows how the connector of RJ-45 is numbered please make sure that the

inserting direction is correct.

Figure A-1 Connector of RJ-45

Pin distribution of 10Base-T/100Base-TX

Unshielded twisted- pair (UTP) or shielded twisted-pair (STP) will be used for the

connection of RJ-45: for the connection of 10Mbps, category 3, 4 and 5 of 100 ohm will

be used, and cat.5 of 100 ohm will be used for 100Mbps. Additionally, do make sure that

the connecting length of any twisted-pair shall not exceed 100 meter.

Port of RJ-45 supports automatic MDI/MDI-X operation, PC or server may be

connected with straight-through cable, or connect with other switch or hub. In

straight-through cable, pin 1, 2, 3 and 6 at one end of the cable are connected to pin 1, 2,

3 and 6 at the other end of the straight-through cable respectively. Cross-over cable must

be used for switch or hub with MDI-X port. The pin distribution of

Warning:

Don’t insert a telephone plug into any RJ-45 port. Only use twisted-pair with RJ45

connectors at both ends conforming to FCC standard.

SICOM3024SM Industrial Ethernet Switch User Manual

- 64 -

10Base-T/100Base-TX is listed in the table A-1.

Table A-1 Pin distribution of 10Base-T/100Base-TX

Pin MDI-X signal name MDI signal name

Receiving data ＋（RD+） Output data＋（TD+）

Receiving data －（RD-） Output data －（TD-）

Output data ＋（TD+） Receiving data＋（RD+）

Output data－（TD-） Receiving data －（RD-）

4，5，7，8

Unused Unused

Note: “+”“-”denoting cable polarity.

Definition of straight-through cable from RJ45 (8-pin) to RJ45 (8-pin)

Figure A-2 Cable sequence of straight-through cable

Definition of Cross-over cable from RJ45 (8-pin) to RJ45 (8-pin)

Figure A-3 Cable sequence of cross-over cable

Appendix B Cable Type and Specifications

- 65 -

Appendix B Cable Type and Specifications

The cable type and specifications are shown as table B-1:

Table B-1 Cable type and specification

Cable Type Max. length

Connect

10Base-T Cat 3,4 and 5 100 ohmUTP 100m RJ-45

100Base-TX Cat 5 -100ohmUTP 100m RJ-45

100Base-FX

50/125 or 62.5/125μm core

multi-mode fiber（MMF）

5km（1310nm MM）

SC/FC/ST

100Base-FX

9/125μm single-mode fiber

（SMF）

40km（1310nm SM）

80km (1550nm SM)

SC/FC/ST

1000Base-T Cat 5-100 ohm UTP 100m RJ-45

1000Base-LX

9μm or 10μm core sigle-mode

fiber (1310nm)

5km LC

1000Base-LX

50/125 or 62.5/125μm core

multi-mode fiber （ MMF ）

(850nm)

550m LC

Appendix C Glossary

- 67 -

Appendix C Glossary

Terminology Explanation

10Base-T

Twisted-pair standard of Cat3, Cat4 and Cat5 in IEEE specification for 10Mbps

Ethernet

100Base-TX

Twisted-pair standard of Cat5 or above in IEEE specification for 100Mbps Fast

Ethernet

100Base-ＦX

Fast Ethernet which uses one pair of multi-mode or single mode optical fiber to

transmit.

1000Base-T

Gigabit Ethernet which using Cat.5 UTP as transmission medium, max effective

transmission distance is up to 100m. U

1000Base-LX

Gigabit Ethernet which uses one pair of multi-mode or single mode optical fiber to

transmit.

Adaptive

A characteristic that is automatically configured to adaptive mode for the speed,

duplex and traffic control port.

Bandwidth

The information capacity that the channel can transmit. For instance, the bandwidth of

the Fast Ethernet is 100Mbps（bit per second）.

Baud Rate

It expresses the signaling rate which is defined as the change times of the status for

the electric or optical transmission medium within 1 second.

Bridge

One of network equipments which run on the layer2 in the OSI layer7 model, and it

can be connected to the LAN or network segment which uses the same protocol. It

presents the automatic network address learning and network configuration function.

Broadcast One data packet is sent to all equipments on the network.

Broadcast storm

Restless forward broadcast frame or multicast frame on bridge caused by the bridge

ring.

SICOM3024SM Industrial Ethernet Switch User Manual

- 68 -

IGMP IGMP means Internet Group Multicast Protocol.

Full Duplex

Use switches to set up the point to point connection among nodes in the LAN and

allow them to receive and send data packet at the same time.

Half Duplex

The communication for two nodes can only move toward one direction at the same

time, but can not move toward both directions.

MDI

It is the Medium Dependent Interface, in which, one Ethernet port is taken as the

receiving terminal to connect to the port of other equipment.

MDI-X Medium Dependent Interface Cross-over

Appendix D FTP Application for Switch Software Update

- 69 -

Appendix D FTP Application for Switch

Software Update

You can use web management to upgrade SICOM3024SM software through switch by

FTP protocol (Switch as Ftp client；PC as Ftp server）. Before update, you need to setup

the Ftp server；FTP server is well-known software, and can be downloaded on the

internet. Here is the step for configuring FTP server.

1. Install WFTPD in PC. Startup WFTPD；shown in figure D-1:

Figure D-1 start up WFTPD software

2. Type in user name, password, main path; click on Security menu, click on

Users/rights, click on the New User in the User/Rights Security Dialog window. As

Figure D-2

SICOM3024SM Industrial Ethernet Switch User Manual

- 70 -

Figure D-2 WFTPD configure user name and password

3. Type in your user name in New User window; here is “test”, click OK, as Figure D-3

Figure D-3 WFTPD configure user name

4. In Change Password window, type in the password in New Password and Verify area,

for example ”test”, click OK.

Figure D-4 WFTPD configure password

5. Set main path in “home directory”; here is E:\study\

Figure D-5 configure user information

Click “Done” to finish FTP server setup

Upload the software to home directory on FTP server, here is under E:\study\

FTP server setup is finished now. For the successful setup we support two software

versions: Host and Backup. The Host version is the one we currently used which is not

Appendix D FTP Application for Switch Software Update

- 71 -

allowed to update for the purpose of protecting software. We use WEB management

software to upgrade it, steps:

1． Enter into WEB management page, click navigation bar to set Update, as Figure

D-6:

Figure D-6 Software Update

2． Set FTP server IP address, user name, password, Update software name, click

Apply button, record update software ID;

3． Wait for upgrade software, Update successful;

4． Click on navigation bar to check version; set updated software ID as startup version;

as FigureD-7:

FigureD-7 inquire Software Version

5. Click Restart under equipment management in navigation bar; as Figure D-8:

Figure D-8 reboot

SICOM3024SM Industrial Ethernet Switch User Manual

- 72 -

6. Wait for 30 seconds，start Web management system; click on navigation bar to check

equipment basic information; software version; sure about the update successfully. As Figure D-9:

Figure D-9 basic information

Update is finish.

KYLAND Technology SICOM3024SM User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual