KYE SYSTEMS GTAA1 Users manual

ENGLISH

GENIUS GRAP H I C TABL E T

Q U I C K I N S TA L L A T I O N G U I D E

CAUTION: INSERT T H E D R I V E R C D I N T O YOU R C O M P U T E R F I R S T AND THEN

FOLLOW T H E IN S T R U C T I O N S TO COMPLET E YOUR SETUP PROCESS.

NOT E : RE M O V E T H E S C R E E N P R O T E C T O R B E F O R E U S I N G T H E TA B L ET.

INTRODUCTIO N

1 —Express Key
2 —LED indicator
3 —Hot cells
4 —Working area
5 —Button 2
6 —Button 1
7 —Pen tips

8 —USB Dongle
9 —Left button
10 —Scroll wheel
11 —Right button

12 —Power switch
13 —USB port
14 —Digital pen slot
15 —Dongle slot
16 —Battery slot
17 —Resume button

DRIVER INS TA L L AT ION

Windows:

1. Insert the driver disc into your computer’s CD-ROM drive. When prompted, select “Driver Setup”, and press OK to
install driver.

Note: In most systems, the Setup Wizard will start automatically. If Automatic Setup does not begin, start the Setup
program manually by selecting “Start/Run”, type "E:\setup", where “E:” represents the location of the CD-ROM
drive, then press “Enter”.
Note: In certain cases, Windows might ask for your permission because it cannot recognize the driver you are
downloading. If this occurs, select “Continue Anyway” and continue to install.

Macintosh:

1. Insert the driver disc into your computer’s CD-ROM drive.

2. Check to see if the “Genius Tablet” is shown on the screen. Double click the icon then follow the instructions.

3. Enter your administrator name and password to process the next step till it’s finished.

Note: For more information, refer to the MAC user manual on the driver disc.

CAUTION: ONCE THE INSTALLATION HAS BEEN COMPLETED, REBOOT YOUR MACINTOSH BEFORE

PLUGGING THE DEVICE INTO YOUR COMPUTER.

1

ENGLISH

HARDWARE INSTA L L AT I O N

CAUTION: MAKE SURE THAT YOU HAVE INSTALLED THE DRIVER

SOFTWARE (SEE ABOVE) INTO YOUR COMPUTER BEFORE
INSTALLING THE HARDWARE.

1. Put the batteries into the back of tablet.

2. Plug the tablet dongle into your computer’s USB port (located on the computer,

display, or keyboard). The tablet’s LED light will indicate the operational status,
and your computer screen will display a “found new hardware” message.

Note : Do not mix or use different types of batteries at the same time such as
Li-Ion, Alkaline, etc; and remember do not put the batteries in the wrong direction.

VERIFYING T H E INSTA LL AT I O N

To ensure that everything has been installed properly, follow the procedures below. Check the User’s manual on the
CD-ROM for more information.

VERIFYING H ARDWAR E A ND DRI VER FU NCTIONS

The LED light on the tablet is the main indicator for hardware operation. The light normally stays off, and will light up
in various situations. Watch the status of the tablet LED light as you go through these steps. None of the steps, except
the last two, require the tablet driver to be installed.

1. As soon as the tablet detects the presence of the digital pen or the pressure of express keys or the wireless
mouse, the LED light will come on briefly, and will normally stay off.

2. When the working area detects the presence of the pen, the LED light will stay on. This happens when the
pen tip is directly above the working area of the tablet and is low enough.

3. When you press a button on the body of the pen or the mouse, the LED light will come on.

4. When you press the pen tip against the tablet anywhere in the working area, the light will also come on.

5. If the tablet driver has been properly installed, a small tablet icon ( ) will appear in system the Task Bar
area, normally at the lower right corner of the screen.

6. With the tablet driver properly installed, moving the pen tip or the mouse over the working area will cause the cursor
on the screen to move accordingly.

7. Test your wireless stylus pen in the tablet working area, if it doesn't work, change the
battery or plug the USB cable into your PC.

8. When in low battery status, the red LED of the tablet will be blinking continuously; it will
stay off when the batteries have been changed. You can remove the USB cable from your
PC and the tablet.

Note : Do not mix or use different types of batteries at the same time such as Li-Ion,
Alkaline, etc; and remember do not put the batteries in the wrong direction.

EXPRESS KEY FUNCTION

Undo Eraser Zoom in Zoom out

These keys are programmable. Go to the Tablet Menu ( ) to set up (check the electronic manual for more information).

2