KYE SYSTEMS GKZGK, GMZGM User Manual

Hardware Installation

1.
You can connect the receiver to a USB port of a PC.

2.
Install two AA rechargeable batteries in the mouse and two AA rechargeable batteries in the keyboard.

3.
Turn on your computer.

4.
After you open Windows, please press the button on the receiver first (RB) and then press the button under
the mouse (MB) and keyboard (KB) for ID channel setting. You only have six seconds to press the receiver,
the channel button on the keyboard (KB), then the receiver button again and the channel button on the
mouse (MB). So you press RB, KB, RB, MB to set the channel setting.
Important: You can use the battery charger receiver to recharge two AA or two AAA rechargeable batteries
each time when you use the PC. Plug the battery charger receiver USB connector into the PC directly and
remember do not put the batteries in the wrong direction, use the same types of batteries, and do not
recharge via the USB hub, that will make your receiver, main-board and hub burn or become non-usable
easily. Also, keep all drinks away! If any spill occurs on the receiver, unplug the USB connector first and
clean the receiver immediately. Please remove the batteries if you do not use this device for at least two
weeks.
Warning: (Troubleshooting)

1.
Please do not use Wireless TwinTouch+ Optical Value on a desk which is made of glass, mirror, iron, or
black velvet. Also, a flat surface is necessary or the Optical Sensor will error easily. When you use
Wireless TwinTouch+ Optical Value on a desk that is made of metal, try using a pad or reduce the
receiving distance.

2.
Before the first installation is completed (channel setting ready), the keyboard will not work in DOS. If
your USB keyboard does not work in BIOS, DOS or Windows, then use another PS2 keyboard to make the
USB controller (USB function) and USB legacy (USB keyboard) “On” in the BIOS setup. This may occur
with older BIOS versions. Then unplug the PS2 keyboard and plug in your USB keyboard and everything
should be working properly.

3.
The Wireless TwinTouch+ Optical Value channel provides 256 ID-codes, and it automatically selects the
ID # for your keyboard and mouse. You can only set up one Wireless TwinTouch+ Optical Value at a time.
But if you have additional Wireless TwinTouch+ Optical Value sets in an area of 10 square meters, more
interference may occur between the receiver and your keyboard and mouse.

4.
If you feel the mouse does not move smooth as usual or the keyboard does not work when typing, then the
batteries have lost their charge, so please replace them. Also, the wireless icon will be blinking “red” when
there is a battery-low situation. The LED on the receiver shows the battery-recharging status (from shining
to LED completely “on” for battery full). You should set up the channel every time you replace the
batterires.

5.
If you need to buy new batteries, please choose Ni-MH (Nickel-Metal-Hydride) AA batteries, 1.2V, 1300
to 1600 mAH. Please do not mix or use other types of batteries (Li-ion, Ni-Cd, Alkaline, etc.).

6.
The Wireless TwinTouch+ Optical Value with radio frequency gives you free movement and an enjoyable
experience. For optimal performance, place the receiver at least 8 inches (about 20 cm) away from the
mouse and other electrical devices, such as the computer, monitor, and etc.
Software Installation

1. Make sure the mouse and keyboard is connected to the computer.

2. Put the Setup disk (or CD) into the disk drive.

3. Follow the instructions on the screen to finish the software installation.
Factory Setting

1. Mouse:
Button Assignments
The Button Assignment feature lets you work in a more efficient way because you can assign the most
frequently used commands in Windows to the mouse buttons.

Magic-Roller
Press the “Magic-Roller” to surf the Internet and Windows documents
Left Button
Provides traditional mouse functions such as click, double click and drag.
Right Button
You can assign this button frequently used keyboard and mouse functions in addition to features like
EasyJump, Auto-Panning, Zoom, etc.
Roller Button
You can assign this button frequently used keyboard and mouse functions in addition to features like
EasyJump, Auto-Panning, Zoom, etc.

2. Keyboard:

1. Rewind: Previous track of audio or video CD’s

2. Play & Pause: Play and pause of audio or video CD’s

3. Stop: Stop play of audio or video CD’s

4. Forward: Next track of audio or video CD’s

5. Vol.-& +: decrease or increase volume

6. My favorite: Open my favorite folder

7. E-mail: Open mail folder

8. Back: See last page when viewing the Internet

9. www: Open browser in Netscape or IE

10. Forward: Go to next page when viewing the Internet

11. Sleep: Turn system into wake up mode

MouseMate Software Features
Browsing Speed
You can adjust the browsing speed when you surf the Internet or Windows documents.
Browsing
Direction
Move the “Magic-Roller” forward and the screen will browse to the top of the document. Move it in
reverse and the document will go in the opposite direction
Button Find
Automatically positions the cursor on the default button, usually the OK button, when the dialog box
appears on your screen.
Trails
This option makes it easier to find the cursor when using an LCD monitor. This option cannot be used if
your monitor does not support it.
Loop
When you move the cursor to the top (or bottom) of the screen, it will automatically move the cursor to the
bottom (or top) of the screen.
Mouse Speed
This function lets you adjust the speed at which the pointer moves across the screen.
Double Click
Speed
Use this function to set the double click speed of the mouse.