Kwikset SmartCode 913 Installation and user guide

61035003

Rev 03

ENGLISH

Installation and User Guide

Required too ls

Ruler4 AA Batterie s

Phillips head screwdriver

Additional Tools (depending on application)

Hammer Wood block

Prepare the door and check dimensions

1

If drilling a new door, use the supplied template and the comp lete
door drilling instructions available at ww w.kwikset.com/doorprep.

Measure to conirm that the ho le in

A

the door is either 21/8" ( 54 mm) or
11/2" (38 mm).

21/8"

54 mm

or

11/2"

38 mm

Note: Additiona l door preparation may be
required for doo rs with 11/2" (38 mm) h oles.
Consult the de adbolt drilling ins tructions at
www.kwikset.com/doorprep.

B C D

Kwik set

1-800-327-5625

www.kwikset.com

Measure to conirm that the b ackset is
either 23/8" or 23/4" (60 or 70 mm).

23/8" or 23/4"

60 or 70 mm

backset

Parts in the box

Latch

“B” is not inc luded. If nee ded,

please cont act Kwikset to order

a drive-in latch fo r your lock.

StrikeCKeys

Adapter
Ring

D

Measure to conirm that the ho le in
the door edge is 1" ( 25 mm).

E

A

B

Mounting
Plate

Interior Assemb ly

M

K L

G

Trad iti ona l

1"

25 mm

Contemporary

M

SmartKey
Too l

Exterior Assem bly

Trad iti ona l

F F

Fasteners

03809 46780

N

P

48654 64109

49191

T

H

Measure to conirm that the do or is
between 13/8" an d 2" (35 mm and
51 mm) thick.

13/8" –2"

35 – 51 mm

Contemporary

Q

S

U

V

Install the latch and strike

2

Is the door edge chi seled? Which latch are you insta lling?

A D

Hold the latch in front of the do or hole, with the latch

B

face lush against th e door edge.

YES NO

or

chiseled

Use latch “A”. If the
latch bolt is not alre ady
extended, ex tend the
latch bolt as shown .

A

not
chiseled

Use latch “B” (n ot
included). If th e latch
bolt is not alread y
extended, ex tend the
latch bolt as shown .

B

A

Is the D-shape d hole centered in the door hole?

C

B

actual

size

NPSQ

Latch “A” Latch “B”

A

YES NO

or

D-shaped hole D-shaped hole

No adjustmen t is required.
Proceed to next st ep.

Rotate latch face as
shown to extend latch .

A

B

Install strike on the door fra me.

E

Make sure the hole in the doo r frame is drilled a

minimum of 1" (2 5 mm) deep.

or

N or P

(2x)

Longer screws
install clos est to
the door jamb.

S (2x)

Q (2x)

B

wood
block

C

door frame

Install the exterior keypad

3

What is the diameter of the hol e in the door?

A

Diameter is 21/8"

(54 mm)

or

21/8"

54 mm

“D” is require d for installation.
Install “D” o n “F”.

F

D

Locate screws for step 3C an d keep them within reach.

B

T

Diameter is 11/2"

(38 mm)

11/2"

38 mm

“D” is not nee ded for
installatio n. Discard “D”.

D

Install exterior keypad a nd mounting plate.

C

a

Cable goes
underneath latch.

c

Keep parallel to

Tighten

screws evenly.

edge of door.

T (2x)

actual

size

T

b

Support exterior
assembly during
mounting plate
installation.

G

F

Route cable throug h
center hole, t hen push
cable into bot tom hole.

d

E

Insert key and
test latch. If latch
does not extend o r

T

retract smoothly,
adjust screws ( T).

Remove key when
inished and make
sure the latch bolt
is fully extende d.

Install the interior assembly

4

Remove battery cover and bat tery pack from interior assemb ly.

A

a

Make sure turnpie ce is in
the vertical p osition.

c

Make sure
turnpiece shaf t is
rotated as shown.

L

Install the batteries and perform the door handing process

5

This step will teach your loc k the orientation of your door and is cruci al to lock operation.

Install 4 AA bat teries in battery pack.

A

b

M

d

K

Do not install

batteries

until step 5.

L

Press and HOLD the Lock b utton

B C

while installing bat tery pack.

Hold button until the latc h bolt
starts moving on its own .

actual

size

U

Install interior a ssembly onto mounting plate.

B

a

L

L

Ensure tight cab le
connection.

align

c

Did the latch bolt retrac t and extend on its own
when the battery pac k was installed?

b

Lay excess cabl e lat inside the
bottom of the inter ior housing.

d

U

(2x)

bottom

hole

Ensure correc t polarity.

For best results , use
new, non-rechargeable
Alkaline batte ries only.

Note: Latch
bolt will only

K

YES NO

Door handin g process

was successfu l! Proceed

to next step after l atch

bolt stops movin g.

or

retract half way.

Remove battery pa ck,

wait 15 second s, then

attempt the proc ess again.

Add user codes (16 max)

6

Programming Timeout

During program ming, if no button is p ressed for ive secon ds, the system will tim e out (indicated by
three beeps an d a red lashing keypad), a nd you will need to resta rt the procedure.

Make sure the door is ope n. Press

A B C

the Program button once .

What lights and sound s does the lock produce?

D

One green la sh with one beep Three red lash es with three beeps

green

Programming wa s successful. Programming wa s unsuccessful.

*Beeping so und will only be heard if sw itch #3 (on the lock interior) is in th e on positon. See “Swi tches and Status LED Col ors” on page 4.

Enter user code. A tot al of 16 user
codes may be programme d.

1x

Press Lock button o nce.

Each user cod e

must be a unique

code betwee n 4

and 8 digits.

or

red

Make sure not to paus e for more than 5 seconds d uring programming.

Make sure the user c ode is not a duplicate an d that it is between 4 and 8 d igits
durin g your n ext at tempt . Make sure the lock h as room for an additio nal code. If

all user code p ositions are ille d, delete a code to make ro om for this one.

Mastercode

For enhanced security, a masterco de may be used when adding and del eting user codes. For more information abo ut the mastercode,
download the Programmin g and Troubleshooting Guide on the Smart Code 913 page at www.kwikset.co m.

3x

Test the lock (review normal operation)

7

Conirm that the code( s) added in previous step can unlock th e door.

Locking the Do or Unlocking t he Door

Press Lock butto n once. Enter user code .

Re-key the lock (if needed) and install the battery cover

8

Re-key the lock (if ne eded). Install the batter y cover.

A B

a a

IMPORTANT:
Remove battery
pack before
re-keying.

b b

K

Re-key the lock
to work with your
existing key. See
the supplied
SmartKey Re-key
instruction s for
more information.

c

Reinstall
battery
pack.

K

H

actual

size

V

M

V (3x)

Reference Guide

SmartCode at a Glance

Exterior

Keypad

SmartKey

tool hole

Lock
button

Keyway

Interior (cover removed)

Back

panel

Program

button

Status

LED

Note: When the cove r is removed,
the turnpiece sh aft can be used to

manually lock a nd unlock the door.

Switches

Turn pi ec e
shaft

System Alerts

Alert Reason Solution

Keypad lashes red three
times with three beeps*.

Keypad lashes red 15 times
with 15 beeps*

Keypad lashes red with fast
beeping sound for three to
four seconds.

Keypad lashes green with
continuous beeping sound
for two seconds.

*Beeping s ound will only be hea rd if switch #3 is on.

Switches and Status LED colors Troubleshooting

Switches

On

1 2 3 4

Switch Function

Door lock status LED blinks every 6

1

seconds

Lock automatically re-locks door 30

2

seconds after unlocking. Disabled if no
codes are programmed.

3 Audio

4 Not used.

O

Status

LED

Color Lock Status

Blinking green Unlocked

Blinking amber Locked

Blinking red Low battery

Door handing process

Solid red

did not work properly.
See the online
Programing and
Troubleshooting Guide.

available on the S martCode 913 pag e at www.kwikset.c om.

One incorrect code entered. Re-enter code.

No user code programmed. Program at least one user code.

Programming timeout after ive
seconds.

Unsuccessful programming.

Three incorrect codes entered
within one minute.

Low battery. Replace batteries.

Door jammed while attempting
to lock.

A complete Progra mming and Troubleshootin g Guide is

Attempt programming procedure again.

Re-enter code after 60 second keypad
lockout.

Manually re-lock door. If needed,
reposition strike.

Deleting a single user code

Note: All codes m ay be deleted at once if the m astercode is enabl ed. For more information ab out the
mastercode, c onsult the online Pro gramming and Troublesho oting Guide.

1 Keep door ope n.

Press Program
button once.

5 Re-ente r user code. 6 Press Lock

2 Press Lock

button once.

button once.

If no button is pre ssed for ive secon ds, the system will time o ut, and

you will need to res tart the procedure .

3 Enter use r code

to be deleted.

If unsuccessful

Make sure to enter
the same valid co de
in steps 3 and 5.

4 Press Lock

button once.

Test co de

While the door i s
open, test the u ser
code to make sure
it no longer unl ocks
the door.

Important Safeguards

1. Read all instruction s in their entirety.

2. Familia rize yourself with all warning and caution st atements.

3. Remind all family mem bers of safety precautions .

4. Protect your u ser codes and mastercode.

5. D ispose of used batterie s according to local laws and regulatio ns.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel

can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete security

by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.

Factory Reset

A factory reset wi ll delete all codes as sociated with the lock .

1 Remove

battery pac k.

3 Press the Pro gram button

once more. In 20 se conds,
when the LED las hes green
and you hear one b eep, the
lock has been re set.

2 Press and H OLD the Program

button while rein serting
the battery pa ck.

Keep holding th e button for 30

seconds until t he lock beeps
and the status LED  lashes red.

4 Perform the doo r handing process a gain

Status
LED

to teach the lock the o rientation of the
door and add us er codes to your lock .