Kwikset SmartCode 909 Installation And User Manual

A

B

W

F

Parts in the box

Latch

“B” is not inc luded. If nee ded,

please cont act Kwikset to order

a drive-in latch fo r your lock.

Exterior
Assembly

Strike Adapter

ring

C D

E

Keys

Mounting
Plate

SmartKey
Too l

G

H

03809 46780

N

Q

S

P

Fasteners

48654 27526 64109

Interior
Assembly

K L M

T

U V

A

N or P

(2x)

NPSQ

A

A

B

B

B

A

B

If drilling a new door, use the supplied template and the comp lete
door drilling instructions available at ww w.kwikset.com/doorprep.

Note: Additiona l door preparation may be
required for doo rs with 11/2" (38 mm) h oles.
Consult the de adbolt drilling ins tructions at
www.kwikset.com/doorprep.

or

backset

Measure to conirm that the h ole in
the door is either 21/8" ( 54 mm) or
11/2" (38 mm).

Measure to conirm that the b ackset is
either 23/8" or 23/4" (60 or 70 mm).

23/8" or 23/4"

60 or 70 mm

13/8" – 13/4"*

35 – 44 mm*

Measure to conirm that the h ole in
the door edge is 1" ( 25 mm).

Measure to conirm that the d oor is
between 13/8" an d 13/4"* (35 mm
and 44 mm*) thick.

A

A B

C

D

B C D

Is the door edge chi seled?

Are the latch holes cente red in the door hole?

Which latch are you insta lling?Hold the latch in front of the do or hole, with the latch

face lush against th e door edge.

21/8"

54 mm

11/2"

38 mm

1"

25 mm

YES

YES

NO

NO

Use latch “A”. If the
latch bolt is not al ready
extended, ex tend the
latch bolt as shown .

No adjustmen t is required.
Proceed to next s tep.

Rotate latch face as
shown to extend latch .

wood
block

actual

size

Use latch “B” (n ot
included). If t he latch
bolt is not alrea dy
extended, ex tend the
latch bolt as shown .

Latch “A” Latch “B”

S (2x)

C

Q (2x)

Longer screws
install clos est to
the door jamb.

door frame

E

Install strike on the door fra me.

Make sure the hole in the doo r frame is drilled a

minimum of 1" (2 5 mm) deep.

or

chiseled

not
chiseled

or

or

1

Prepare the door and check dimensions

2

Install the latch and strike

*Service kit s for 21/4" (57 mm) thick doo rs
are available thro ugh Kwikset.

1 / 4

62888 / 01

Installation and User Guide

Kwik set

1-800-327-5625

www.kwikset.com

ENGLISH

Required too ls

Ruler4 AA Batterie s

Hammer Wood block

Phillips head screwdriver

Additional Tools (depending on application)

21/8"

54 mm

11/2"

38 mm

actual

size

T

What is the diameter of the ho le in the door?

Install exterior keypa d and mounting plate.Insert cylinder into keypad.

A

B

C

Diameter is 21/8"

(54 mm)

Diameter is 11/2"

(38 mm)

or

“D” is require d for installation.
Install “D ” on “F”.

“D” is not nee ded for
installatio n. Discard “D”.

Cable goes
underneath latch.

Locate screws
and keep them
within reach.

Support exte rior assembly

during mountin g plate installation .

Route cable throu gh
center hole, t hen push
cable into side h ole.

Insert key and
test latch. If latch
does not exten d or
retract smoothly,
adjust screws ( T).

Remove key when
inished and make
sure the latch bolt
is fully extende d.

Keep parallel to

edge of door.

Tighten

screws evenly.

a

d

b

c

e

D

D

F

F

T

G

T (2x)

W

F

T

E

Install the exterior keypad

Remove battery cover. Remove battery pack . Make sure the turnpiece is in th e vertical position.

A B C

vertical

M

L

K

L

Do not install

batteries

until step 5.

Note: Turnpiece
may not rotate
smoothly until
after step 5.

Connect cabl e. Ensure tight cable
connection.

Lay cable lat again st the interior
housing.

Push turnpiece shaf t onto
torque blade.

Secure interior assem bly with
supplied screws.

D E F G

turnpiece
shaft

torque
blade

L

U (2x)

actual

size

U

Install the interior assembly

YES NO

or

Door handin g process

was successfu l! Proceed

to next step after l atch

bolt stops movin g.

Remove battery

pack, wait 15 se conds,

then attempt th e

process again.

This step will teach your loc k the orientation of your door and is cruci al to lock operation.

Install 4 AA bat teries in battery pack. Press and HOLD the Lock button

while installing bat tery pack.

Hold button until the la tch bolt
starts moving on its own .

Did the latch bolt retrac t and extend on its
own when the battery pa ck was installed?

A B C

Ensure correc t polarity.

For best results , use
new, non-rechargeable
Alkaline batt eries only.

K

Install the batteries and perform the door handing process

2 / 4

3

4

5

1x

green

3x

red

3 / 4

Conirm that the code (s) added in previous step can unlock th e door.

Make sure the door is ope n. Press
the Program button the num ber of
times that correspon ds to the user
code position being p rogrammed.

Locking the Do or Unlocking t he Door

Enter user code. A tot al of 8 user
codes may be programm ed.

Press Lock button o nce.

A B C

What lights and soun ds does the lock produce?

D

Each user cod e

must be a unique

code betwee n 4

and 8 digits.

Example: If
programming
the third code,
press the but ton
three times.

Programming wa s successful. Programming wa s unsuccessful.

Make sure the user c ode is not a duplicate an d that it is

between 4 and 8 d igits during your next a ttempt.

Press Lock butto n once. Enter user code .

Programming Timeout

If no button is p ressed for ive secon ds, the system will time
out and you will ne ed to restart the proce dure.

*Beeping s ound will only be heard if sw itch #3 (on the lock interior) is in th e on positon. See “Sw itches and Status LED Col ors” on page 4.

Mastercode

For enhanced se curity, a mastercode may be u sed when adding an d deleting user code s. For more information a bout the mastercode , download the Program ming
and Troubleshooti ng Guide on the Smart Code 909 page at ww w.kwikset.com.

2x

One green la sh with one beep* Three red lash es with three beeps* Two beeps*

or or

Programming time out.

Make sure not to paus e for more

than 5 second s during programming .

Tip: You can press th e
Lock button befo re
entering your user
code to light up the
keypad at night .

Re-key the lock (if ne eded). Install the batter y cover.

A B

IMPORTANT:
Remove
battery
pack before
re-keying.

K

K

M

H

V (3x)

a a

b b

c

Re-key the lock
to work with your
existing key. See the
supplied SmartKey
Re-key instruction s
for more
information.

Reinstall
battery
pack.

actual

size

V

Re-key the lock (if needed) and install the battery cover

6

7

8

Add user codes (8 max)

Test the lock (review normal operation)

Alert Reason Solution

Keypad lashes red 1 time
with 1 beep*

Door jammed while
attempting to lock.

Manually re-lock door. If needed,
reposition strike.

Keypad lashes red 3 times
with 3 beeps*

Unsuccessful programming.

Attempt programming procedure
again.

One incorrect code entered. Re-enter code.

No user code programmed. Program at least one user code.

Keypad lashes red 10
times with 10 beeps*

Low battery. Replace batteries.

Lock beeps 2 times.

Programming timeout.

Attempt programming procedure
again, making sure not to pause for
more than 5 seconds.

Keypad lashes red 3 times.

Keypad lashes red 6 times
with 6 beeps*.

Keypad lashes red 15 times
with 15 beeps*

Three incorrect codes entered
within one minute.

Re-enter code after 60 second keypad
lockout.

*Beeping s ound will only be hea rd if switch #3 is on.

© 2015 Spectrum Brands, Inc.

1. Read all instruction s in their entirety.

2. Familiarize yourself with all warning an d caution statements.

3. Remind all family me mbers of safety precaution s.

4. Protect your user codes and mas tercode.

5. Dispose of use d batteries according to local law s and regulations.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel

can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete security

by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.

Important Safeguards

4 / 4

SmartCode at a Glance

Deleting a user code

In order to delete a u ser code, you must over ride the code by adding a d i erent u ser code in the same
position. For e xample, if you want to del ete the third code, add a di  erent us er code in position th ree.

Test the old user cod e to make sure it can no longe r unlock the door.

If you cannot rem ember the user cod e position, you may wish to p erform a factory res et to delete all
codes assoc iated with the lock.

Reference Guide

Exterior

Back

panel

Program

button

Status

LED

Switches

Turn pi ec e

Interior (cover removed)

Switches and Status LED colors Troubleshooting

Switch Function

1

Door lock status LED blinks every 6
seconds

2

Lock automatically re-locks door 30
seconds after unlocking. Disabled if no
codes are programmed.

3 Audio

4 Not used

Color Lock Status

Blinking green Unlocked

Blinking amber Locked

Blinking red Low battery

Solid red

Door handing process
did not work properly.
See the online
Programing and
Troubleshooting Guide.

1 2 3 4

On

Switches

Status

LED

O

System Alerts

Factory Reset

A factory reset w ill delete all codes as sociated with the lock .

Status
LED

1 Remove

battery pac k.

2 Press and H OLD the Program

button while rei nserting
the battery p ack.

Keep holding th e button for 30

seconds unti l the lock beeps
and the status LED  lashes red.

Keypad

Lock
button

Keyway

SmartKey

tool hole

3 Press the P rogram button

once more. Whe n the LED
lashes gre en and you
hear one bee p, the lock
has been rese t.

4 Perform the do or handing process a gain

to teach the lock th e orientation of the
door, and add use r codes to your lock.

A complete Smar tCode 909 Program ming and

Troubleshooting G uide is available at ww w.kwikset.com.

23/8" (60 mm)

23/4" (70 mm)

Backset • Distancia al centro

Centerline

Linea central

13/8" (35 mm)

13/4" (44 mm)

21/4" (57 mm)

Face of the door

Frente de la puerta

Edge of the door

Borde de la puer ta

Fold

Doble

Installation Guide

Guía de instalación

18003275625 • www.kwikset.com

If drilling a n ew door, use
the supplie d template and
the complete d oor drilling
instructio ns available at
kwikset.com/doorprep

Si va a perforar u na
puerta nueva , utilice la
plantilla sum inistrada y las
instruccion es completas para
la perforaci ón de la puerta
en kwikset.com/doorprep

Parts in the box

Piezas en la caj a

Required tool s

Herramientas necesarias

*Passage knobs only: Call
Kwikset to order a s ervice kit
for 21/4" (57 mm) thi ck doors.

*Perillas de paso s olamente:
Llame a Kwikset para pe dir un
kit de servicio p ara puertas
gruesas con un esp esor
de entre 57 mm (21/4" ).

Latch

Pestillo

Passage Kno bs

Perillas de paso

Screws

Torn il los

Strike

Placa

Privacy
Knobs

Perillas de
privacidad

Emergency Unlock tool
(privacy locks only)

Herramienta pa ra el
desbloqueo de emergencia
(las cerraduras de
privacidad solamente)

Not required fo r all applicatio ns

No se requiere para to das

las aplicaciones

23/8" (60 mm)

or • o

23/4" (70 mm)

13/8"–13/4" *

35 mm–44 mm*

21/8"

54 mm

1"

25 mm

Do not remove
screws!

¡No retire los
tornillos!

Hold the latch i n front of the door ho le, with
the latch face l ush against the d oor edge.

Sostenga el p estillo en frente del ori icio
de la p uerta, con la cara d el pestillo
al ras con el borde de la puerta.

If the latch hol es are centered i n the door hole,
no adjustm ent is required . Proceed to step 4.

If the latch hol es are NOT centere d, adjust
latch. See “Latch Adjustmen t” (step 3C).

Si los oriic ios del pestillo es tán centrados con el o riicio
de la puerta , no se requiere ajusta rlo. Vaya al paso 4.

Si los oriici os del pestillo NO es tán centrados, aju ste
el pestillo. C onsulte “Ajuste del pest illo” (el paso 3C).

Latch Adjustm ent (only if neede d)

Ajuste del pes tillo (si es necesa rio)

Drilling Template

Plantilla de pe rforación

Move the pin to
extend the latch .

Mueva el pasado r
para extender
el pestillo.

Template is only need ed if a new hole must be dri lled in the door.

La plantilla sol o se necesita en caso de q ue deba

perforarse un n uevo oriicio en la puer ta.

62820 / 01

Additional tools
(if needed)

Herramientas adicionales
(si es nece sario)

wood block

bloque de madera

not centered

no centrado

centered

centrado

Instructions continue on reverse

Las instrucci ones continúan en e l reverso de la hoja

Twist the side
with the holes.

Gire el lado con
los oriicios.

counter-clockwise

sentido antiho rario

Pull to

separate

knobs.

Tire para

separar las

perillas.

A

C D

H

F

K

E

J

G

B

A

A

B

C

Set knobs aside until step 5.

Deje a un lado la s perillas hasta el p aso 5.

A

B

C

or • o

Prepare door and check dimensions

Prepare la puerta y revise las dimensiones

1

Disconnect knobs (if pre-assembled)

Desconecte las perillas (si previamente ensambladas)

2

Adjust the backset of the latch (if needed)

Ajuste la distancia al centro del pestillo (si es necesario)

3

Door edge N OT
chiseled

La puerta si n el
borde cincela do

Door edge chiseled

La puerta co n el
borde cincela do

align

alinear

G

A

E / J

Press latch bolt
to install knob.

Presione el pern o
de retención
para instalar la
perilla exterior.

Push up on knob while tightening
screws to keep latch horizontal
and centered.

Empuje hacia arrib a la perilla
mientras ajusta l os tornillos para
mantener el pestillo en forma
horizontal y centrada.

Close door an d test latch operati on. If latch is
loose in the s trike, adjust st rike tab so it grips
the latch bolt b etter when the do or is closed.

Cierre la puert a y pruebe el funcion amiento
del pestill o. Si el pestillo qued a suelto
en la cerradura ti po hembra, ajuste la
lengueta de l a cerradura tipo hemb ra para
que sujete mejo r el perno de retención
cuando la puerta se encuentre cerrada.

H

D (2x)

Save the bedroom/bathroom emergency
unlock tool (G) for future use.

Guarde la herra mienta (G) para abrir
la recámara o el baño en casos de
emergencia para utilizarla en el futuro.

tab

lengueta

IM PORTANT: If installing a pas sage lock on an

entry door, make s ure the knob with the s crew
holes is on th e interior side of th e door.

slant of latch bol t faces door fram e

la in clinación del perno qu eda

enfrentada al marco d e la puerta

door frame

marco

C (2x)

wood block

bloque de madera

slant of latch bol t faces door fram e

la in clinación del perno qu eda

enfrentada al marco d e la puerta

door frame

marco

Remove plates

Elimine las placas

Install drive -in collar

Instale el aro de emp uje

A

B

Register your pro duct at www.kwiks et.com/productre gistration

Rate your produc t at www.kwikset.c om/reviews

Registre su producto en ww w.kwikset. com/product registration

Clasiique su produc to en www.kwikset.com/reviews

©2015 Spectrum Brands, Inc.

IMP ORTANTE: En caso de instalar una

cerradura de pas o en la entrada de una puer ta,
asegúrese de que l a perilla con los oriici os de
los tornillos est á en el lado interior de la pu erta.

F / K

A

A

B C

D

B

or

o

Align round edges.

Alinee los borde s
redondos .

To catch screws:

Para atrapar tornillos:

1. Twist counter- clockwise

Gire sentido ant ihorario

2. Push while twisting

Empuje mientras gira

3. Twist clockwise

Gire sentido ho rario

Install latch

Instale el pestillo

4

Install knobs

Instale las perillas

5

Install strike on door frame

Instale la placa en el marco de la puerta

6

Privacy locks only

Cerraduras de privacidad solamente

!