Page 1
53733-001
Rev 01
9240
Parts in the box
ENGLISH
Installation and User Guide
Kwikset Technical Support | 1-800-327-5625 | www.kwikset.com
Required tools
Batteries
Additional Tools (dep ending on application)
1
Ruler
Hammer Wood block
Prepare the door and check dimensions
Screwdrive rs
Latch
Mounting
Plate
Collar
Key
Exterior AssemblyInterior Assembly
Contempo rary Traditional
For Latch / Strike For Lock
Strike
53648
52502
53646
Transitional
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.
A
the door is either 2-1/8 in (54 mm) or
1-1/2 in (38 mm).
2-1/8 in
54 mm
or
1-1/2 in
38 mm
Note: Additional door preparation may be
required for doors with 1-1/2 in (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep.
Install the latch and strike
2
B C D
either 2-3/8 or 2-3/4 in ( 60 or 70 mm).
2-3/8 or 2-3/4 in
60 or 70 mm
backset
the door edge is 1 in (25 mm).
25 mm
1 in
Measure to conrm that the door is
between 1-3/8 and 1-3/4 in (35 mm and
44 mm) thick.
1-3/8 – 1-3/4 in
35 – 44 mm
Note: Please contact customer service if door
thickness exceeds 1-3/4 in for a thick door kit.
(4x)
For Latch /
Strike Bag
53648
actual size
Hold the latch in front of the door hole, with the latch
A
Is the rectangular shaped hole centered in the
door hole?
YES NO
or
Rectangular shaped holeRectangular shaped hole
No adjustment is required.
Proceed to next step.
Rotate latch face as
shown to extend latch.
180°
Is the door edge chiselled?
B
YES NO
chiseled
Install l atch in door with
supplie d screws.
Make sure
slotted hole is at
bottom of latch.
or
Use a athead screwdriver to remove
latch face. Once removed, grip the
latch with one hand and with the
other hand twist collar o. Install
drive-in collar.
Align tabs with
holes in collar.
not
chiseled
Ensure colla r
snaps into place .
Pull collar to te st
for tight t.
Install l atch in
door with wood
block and
hammer.
Install strike on the door frame.
C
Make sure the hole in the door frame is drilled a
minimum of 1 in (25 mm) deep.
D
IMPORTANT: Make sure the latch bolt is fully
retracted (in the unlocked position).
53648
(2x)
(For Latch/
Strike Bag
)
C
door frame
unlocked
53648
(2x)
(For Latch/
Strike Bag
)
Make sure
slotted hole is at
bottom of latch.
1 / 4
Page 2
Install the exterior keypad
3
For Lock
Bag
53646
(2x)
actual size
What is the diameter of the hole in the door?
A
Diameter is 2-1/8 in
(54 mm)
or
2-1/8 in
54 mm
Adapter ring is required for
installation.
Locate screws for step 3C and keep them within reach.
B
53646
(2x)
(For Lock Bag)
Diameter is 1-1/2 in
(38 mm)
1-1/2 in
38 mm
Adapter ring is not needed
for installation.
Install exterior keypad and mounting plate.
C
a
Make sure bolt
is RETRACTED
c
Tighten screws
evenly.
over tighten screws.
(For Lock Bag)
Rotate the at blade to a
horizontal position to match
the latch orientation.
Cable goes
underneath latch.
TOP of the mounting plate
should be visible
Keep parallel to edge of door.
DO NOT
53646
(2x)
Make sure the flat
blade is centered in the
mounting plate hole.
b
d
Support exterior
assembly during
mounting plate
installation.
Route cable through
center hole, then push
cable into bottom hole.
Insert key and
test latch. If latch
does not extend or
retract smoothly,
adjust screws.
Remove key when
sure the latch bolt
is FULLY EXTENDED.
Install the interior assembly
4
Remove interior cover from interior assembly. Secure the interior assembly onto the mounting plate.
A B
a
Check to make sure the latch bolt
is in the extended/locked position
to install the interior assembly.
Remove the interior cover
c
from the interior assembly.
Make sure turnpie ce shaft
b
is rotated as shown.
If the turnpiece is not pointing up,
rotate the turnpiece until you hear a click.
d
Do not install batterie s
until step 5.
a
Connect the cable.
Ensure a tight cable connection.
Insert the flat blade into
c
the turnpiece shaft.
For Lock
Bag
b
Route cable around the side
notch and bottom of the
interior assembly.
d
52502
(2X)
Ensure you a re using the correc t
screws. Using incorrect screws will
damage the product.
52502
(2x)
actual size
Install the batteries in the interior assembly
5
Install 4 AA batteries in interior assembly
A
Ensure your door is open while installing batteries.
Ensure the interior cover is o to install batteries.
Note: Batteries are not included
Ensure corr ect polarity.
For best resu lts, use
new, non-rechargeable
alkaline bat teries only.
Install interior cover for the interior assembly.
B
2 / 4
Page 3
Add user codes (12 max)
6
A C D E
During User Code programming,
a time out will occur if the keypad
is not pressed for 5 seconds and
you will need to restart the
procedure.
For security reasons, the
first 4 digits of each User
Code must be unique. For
example, you are unable to
program a user code 1-2-3-4-5
as well as user code 1-2-3-4-6.
Test the lock (review normal operation)
7
Before you can lock and unlock the door a User Code must be created. Refer to Step 6 for instructions how to create a User Code.
Conrm that the code(s) added in previous step can unlock the door.
Make sure the interior
cover is o. Press the
Program button once.
Press number .
B
Press button once. Enter user code. A total
of 12 user codes may
be programmed. User
codes should be 4 to 8
digits in length.
Press button
again.
Note: After the rst User Code is created, the latch
bolt will automatically retract and extend to learn
the locking and unlocking direction of the door.
The lock button will indicate success or failure.
GREEN: Success RED: Unsuccessful
To lock your door, press the lock button. The lock will beep twice and
the lock button will ash amber as the deadbolt extends.
BA
To unlock your door, enter the user code. The lock will beep twice and the
lock button will ash green and the deadbolt retracts.
Adding a One-time User Code
8
1.
Remove interior cover.
Press programming
button.
4.
Press the button.
Up to 2 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length.
The One-Time User Code will be deleted automatically after it is used. The same One-Time User
Code can be created again after it’s used.
10
Delete ALL User Codes
Note: Keypad locking function will be disabled when User Codes are deleted. The lock
can only be operated manually by a key during this time.
1.
Remove interior cover.
Press programming
button.
Press number .
2.
5.
Enter the one time
user code.
2.
Press number .
3.
Press number .
6.
Press the button
again.
3.
Press the
button.
Delete a Single User Code
9
1.
Remove interior cover.
Press programming
button.
5.
Press the
button again.
If a button is not pressed within 5 seconds, the system will time out, and you will need to
restart the procedure.
11
Enable/ Disable Audio
1.
Remove interior cover.
Press programming
button.
2. 4.
Press number .
6.
Enter the user code
being deleted again.
2.
Press number .
3.
Press the
button.
7.
Press the
button again.
If unsuccessful:
Make sure you entered the
same user code in steps 4
and 6.
Test code while the door
is open. Test the User Code
to make sure it no longer
unlocks the door.
Enter the user code
you want to delete.
3.
Press number
again.
4.
Press number .
5.
Press the button again.
3 / 4
4.
Press the
button.
Note: LED status indicator will still function once audio is disabled. Repeat the
programming steps to enable the audio.
Page 4
12
Enable/ Disable User Codes
Reference Guide
13
Enable/ Disable Auto-Lock
Note: When all User Codes are disabled, all electronic functions will be disabled as well.
The door must be locked or unlocked manually with the key. Repeat the programming
steps to enable the User Codes.
1.
Remove interior cover.
Press programming
button.
4.
Press the button.
14
Change Auto-Lock Time Delay
1.
Remove interior cover.
Press programming
button.
Press number .
2.
2.
Press number .
Press number .
3.
Press number .
3.
1.
Remove interior cover.
Press programming
button.
4.
Press the button.
Repeat the programming steps to disable the auto-lock.
15
Door Rehanding
1.
Remove interior cover.
Press programming
button.
Press number .
2.
Press number .
2.
3.
Press number .
3.
Press the button.
4.
Press the button.
16
Factory Reset
Note: Lock must be in a unlocked position to factory reset.
1.
Remove interior cover.
PRESS and HOLD
programming button for
15 seconds.
A factory reset will delete all User Codes and change all programming to factory settings. At
this time, the lock can only be locked or unlocked manually with the key.
5.
Choose and press button
for delay.
30 seconds
1 minute
3 minutes
The lock will have a long
2.
beep.
5 minutes
10 minutes
3.
5.
Press the
button again.
Press programming
button once more.
The latch bolt will extend and retract to learn the orientation of the door.
Note: Perform this process for the lock to learn the locking and unlocking direction of the door.
This feature is used for the lock to learn the orientation of your door (left- or right-handed). If
stuck/jammed bolt error continues to occur after performing this step, please make sure there is
no obstruction from strike or door jamb to prevent the bolt from extending.
17
Add/ Change Programming Code
1.
Remove interior cover.
Press programming
button.
4.
Enter Programming Code.
2.
Press number .
3.
Press the
button.
5.
Press the button again.
Enable/ Disable Programming Code:
Optional: A Programming Code enables you to make programming changes without needing
to access the Programming Button. This is ideal for landlords to program the lock without
access to the interior programming button.
Note: Once Programming Code is enabled, the Programming Button is disabled and can
only be used to factory reset the lock.
One Programming Code between 4 to 8 digits can be saved and cannot be the same as any
User Code and cannot be used as a User Code to unlock the lock.
To program the lock with Programming Code:
Programming
Code
Follow the programming steps WITHOUT
PRESSING the PROGRAMMING BUTTON
To disable Programming Code:
Programming
Code
Programming
Code
Powerbolt at a Glance
Exterior
Lock
Button
Interior
Battery
Holder
Programming
Button
Turnpiece
Number
Buttons
Key
Cylinder
Interior
Cover
System Alerts
Exceed 3 incorrect
User Code attempts
Factory Reset
Successful
Factory Reset
Unsuccessful
Programming
Successful
Programming
Unsuccessful
Lights SoundsAction Troubleshoot
Flashes GREEN x2 2 beepsSuccessful Unlock
Flashes AMBER x2 2 beepsSuccessful Lock
Flashes RED x10 10 beepsLow battery Install fresh new batteries
Flashes RED x 3 3 beepsIncorrect User Code Check code, and retry
Flashes RED x15 15 beeps
Alternate RED/
WHITE Flash x5
Flashes GREEN x1 1 beep
Flashes RED x3 3 beeps
Flashes GREEN x1 1 beep
Flashes RED x3 3 beeps
5 beepsStuck/Jammed bolt Clear jam and try again
Wait 1 minute, check code,
and retry
Retry factory reset steps.
Make sure to press the
Programming Button one
more time within 10 seconds
after the long beep.
Review Programming steps
Important Safeguards
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution
statements.
3. Remind all family members of safety precautions.
4. Always have access to your lock’s standard key.
5. If using the Auto-Lock features, make sure you have your
standard key with you to prevent locking
yourself out.
6. Familiarize yourself with the system alerts.
7. Replace low batteries immediately.
8. Dispose of used batteries according to local laws and
regulations.
WARNING:
This Manufacturer advises that no lock can provide complete
security by itself. This lock may be defeated by forcible or technical
means, or evaded by entry elsewhere on the property. No lock can
substitute for caution, awareness of your environment, and common
sense. Builder’s hardware is available in multiple performance grades
to suit the application. In order to enhance security and reduce risk, you
should consult a qualified locksmith or other security professional.
CAUTION:
Prevent unauthorized entry. Since anyone with access to the back panel
can change the User Codes, you must restrict access to the back panel
and routinely check the User Codes to ensure they have not been altered
without your knowledge. The use of a programming code can help
protect your system’s settings.
4 / 4
© 2022 Spectrum Brands, Inc.
Loading...