Page 1
1
2
1 / 4Kwikset Technical Support: 18668 636584 • www.kwikset.com
Installation and User Guide
ENGLISH
66452001
Rev 01
914C
ZWa ve® P lus
View interactive, animated
instructions online at
http://kwik.st/convert-zw
or continue to use the
paper instructions.
Tools needed
4 AA batterie s Optional: M asking tapeExisting keyPhillips head screwdriver Ruler
Online interactive instructions
Kit "A" Kit "B" Kit "C "
Mounting
plate screws
Mounting
plate screws
Mounting
plate screws
Black mount ing
plate
Interior
cover
Interior
assembly
Battery
pack
Silver mounting
plate
Gold mounting
plate
Black adapt er
Gold adapter
Gold adapterBlack adapt er
Silver adapter
Interior assembly
screws
Interior assembly
screws
Interior assembly
screws
Interior cover
screws
Interior cover
screws
Interior cover
screws
Prepare your door
Determine the parts needed for your door
Make sure your exist ing deadbolt is comp atible. If you have a stan dard deadbolt moun ted
separately from th e handle below it, it is c ompatible with Kwikset Co nvert.
Make sure your doo r is aligned before
proceeding with installation.
A B
Look into the hole in your d oor.
What shape is your torque b lade (the part sticking out throug h the latch)?
For a list of compatible deadb olt
models, plea se see the Kwikset
Convert page at ww w.kwikset.com
Mortise
Lock
Not CompatibleNot Compatible
Rim
Lock
Integrated
Interior
Not CompatibleCompatible
D-shape
Kwikset and Weiser deadbolts:
Use kit “A” for your door.
Baldwin Reserve and
Baldwin Prestige deadbolts:
Use kit “B” for your doo r.
You will need the black adapte r
and the thicker gold screw s.
thicker
screws
Vertical rectangle
Baldwin Estate deadbolts:
Use kit “B” for your doo r.
You will need the gold adapte r
and the thinner gol d screws.
thinner
screws
Slanted rectangle
Schlage deadbolts:
Use kit “C” for your door.
You will need the silver adapter.
Horizontal rectangle
Schlage deadbolts:
Use kit “C” for your door.
You will need the gold adapter.
Make sure your doo r is open and
extend your latch b olt. Make sure your
key is NOT in the deadbo lt exterior.
extended
Remove all existing d eadbolt hardware
from the interior s ide of your door.
D
Optional: S ecure your deadbolt
exterior with mas king tape.
E
Measure to con irm that your door is eith er
13/8" or 13/4" (35 m m or 44 mm) thick.
13/8"or 13/4"
35 or 44 mm
C F
You should be abl e to lock and
unlock your door smoothly
without any res istance, and
without pushing, pulling
or lifting you r door.
If your door is no t aligned, you
may need to orde r a Warped
Door Servi ce Kit, available
through Kwikset S upport:
18668636584
Page 2
2 / 4Kwikset Technical Support: 18668 636584 • www.kwikset.com
3
Install the mounting plate and test your latch
torque blade
Note: A D-shap ed torque blade is shown, but in stallation is the same for all mod els.
A
C D
Place the mounting plate on th e door so that the torque
blade insert s through the center hole.
Kwikset & Weiser On ly:
To determine which mounting
screws to use, test o ne of
the thicker screws irst .
If the thicker screw its , continue
installing the thicker s crews.
If the thicker screw doesn' t it,
install the thinne r screws.
Remove the masking tape fro m the exterior deadbolt, and i nsert
your key and test the latch for smo oth operation.
Remove your key and make sure the bolt is fu lly extended.
fully
extended
If the latch does n ot
extend or retract
smoothly, adjust t he
mounting screws.
B
Keep parallel to th e
edge of the doo r.
Tighten
screws evenly.
Secure the mounting plate with th e mounting screws.
4
Install the interior assembly
D
Secure with two (2) inte rior assembly screws.
bottom
hole
Remove the interior cover and bat tery pack.
A
align tabs
Gold adapter:
Keep slot vertical.
Press adapter irm ly onto
the interior assemb ly.
Install the adapte r on the interior assembly.
back view
of interior
assembly
B
Silver adapter:
Tab is on bottom.
Black adapter:
Curve is on top.
a
b d
Make sure the
turnpiece is in th e
vertical po sition.
Remove the
interior cover.
Remove the batter y pack.
Do not
install
batteries
yet.
vertical
c
Make sure shaft i s oriented
as shown. If nee ded, rotate
the shaft to this p osition.
Stripe should
be vertical.
C
Align the adapter with the torq ue blade and push the interior as sembly
onto the mounting plate.
Schlage Deadbolts Only:
You may need to rotate
the adapter to align with
the torque blade.
actual
size
Page 3
3 / 4Kwikset Technical Support: 1866 8636584 • www.kwikset .com
Add the lock to your smart home system
window
If you wish to unlock
the window, you can
slide it up for more
convenient access
to the programming
buttons while the
cover is installed.
To unlock the
window, remove
the security screw.
The window
on the interior
cover is locked
by default to
prevent someone
from tampering
with your lock's
settings.
Important Information about th e interior cover
Cover Installation:
Install cover.
Note: You may need to
rotate the turnpie ce to align
with the turnpie ce shaft.
turnpiece
shaft
Install screws .
a
b
Install the interior cover
Note: The interior cover an d
screws must be remove d
for battery pack a ccess.
actual
size
Check the Status LED
This step will teach the loc k the orientation of your door and is crucia l for lock operation.
Perform the door handing process
5
6
7
8
The Status LED blinks every s ix seconds to communicate
whether the door is lo cked or unlocked.
Use your key to lock and unlo ck your door, and verify
that the Status LED is communicatin g correctly.
If the Status LED is displaying the wro ng door
lock status, lip switch # 4 to the ON position.
A B C
A B C D
Install 4 AA ba tteries
in the battery p ack.
Ensure correc t polarity.
For best resul ts, use new,
non-rechargeable Alkaline
batteries o nly.
Make sure the door i s open. Insert th e battery pack
while PRESSI NG AND HOLD ING the Program but ton.
Keep pressing th e button for three seco nds after the
battery pac k is installed, the n release the button .
The Status LED will lash red and
green, and th e lock will beep.
Press and re lease the Prog ram
button again.
The latch bolt will re tract and extend on its own
to learn the orien tation of the door. Did the
Status LED turn gree n or red?
If the bolt doe s not move, make sure
the batterie s are installed correc tly,
and perform ste ps 5A5D again.
status LED
Metal
contacts
at bottom,
facing out.
BALDWIN ESTATE DEADBOLTS:
If your latch bolt is to the RIGH T of your interior assembly, and the
Status LED is solid red af ter door handing, press a nd release the
Program button again. The door handing process wi ll restart.
If you are unsure if your lock i s Baldwin Estate, see
chart on page 1 or com patible deadbolt list online.
Red Status LED
Green: Door handing
successful . Continue
to step 6.
Red: See “Red Status
LED” below.
Right
OTHER DEAD BOLTS:
If the Status LED is solid red a fter door handing, make sure
the batteries are inst alled correctly and the lock interio r
is correctly install ed. Perform steps 5A5D again.
Amber:
Locked
Green:
Unlocked
Switch #4
Initiate the process to ad d the
lock to your system at your smar t
home controller. Refer to your
smart home system in structions
for more inform ation.
When prompted by your sm art home system to add the
lock, press but ton “A” on the lock interior one tim e. The
red LED will illuminate when th e lock enters Add Mode.
If successful, re -name the lock in your system
(if applicable).
If unsuccessful , follow your system's instructions to
remove the lock from the control ler and any other
network, then pres s button “A” on the lock one time.
Perform steps 7A7C again.
If still unsucces sful, see "Troubleshooting: Addi ng
the Lock to a Smart Ho me System" on page 4.
A B C
D
button “A”
Please allow time for the con troller to add the lock.
Page 4
4 / 4Kwikset Technical Support : 18668636584 • w ww.kwikset.com
© 2017 Spectrum Brands, Inc.
Reference Guide
These features c an be adjusted in som e smart home apps .
Factory Reset
A factory reset will re move your lock from your smart home system .
Some ZWave® systems require that the lock be with in 12" of the controller during the addin g
process. If this is th e case, follow the steps below to rem ove the lock interior from the door
to perform the proce ss closer to the controller:
1. Remove the small screws that se cure the
interior assembly to th e mounting plate.
2. Rem ove the interior assembly from the door. 3. H old the interior assembly a maximum of 12 " (305 mm) from
your smart home contro ller for the rest of this process.
Status
LED
1 Remove
battery pack .
2 Press and HOLD the
Program button while
reinserting th e battery pack.
Keep holding the but ton
for 30 seconds until
the lock beeps an d the
status LED lashes re d.
3 Press the Program
button once more . When
the LED lashes gree n
and you hear one be ep,
the lock has bee n reset.
4 Per form the door handing process
again to teach the lock th e
orientation of the door a nd pair the
lock to your smarthom e system.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Always have access to your lock’s standard key.
5. If using the Auto-Lock feature, make sure to have your
standard key with you to prevent locking yourself out.
6. Replace low batteries immediately.
CAUTION: Prevent unauthorized entry. Restrict access to your lock’s back panel and
routinely check your settings to ensure they have not been altered without your
knowledge.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.
Important Safeguards
Kwikset Convert at a Glance
AB
Button “A”
Back panel
Program button
Tur npi ece sha ft
Switches
Button “B”
Status LED
Switche s
1. Status LED
Door lock status LED blinks every 6
seconds. ON position is factory default.
2. Auto-Lock
Automatically re-locks door 30
seconds after unlocking. OFF
position is factory default.
CAUTION: With this feature
enabled, it is possible to lock
yourself outside.
on o
3. Audio
Beeping sound is heard during
programming and normal operation.
ON position is factory default.
4. Invert
Only used if the Status LED is
communicating the opposite
door lock status.
1234
Status LED Notiications
Troubleshooting: Adding the Lock to a Smart Home System
Amber las h
Door is locked.
Green lash
Door is unlocked .
Red lash
The 4 AA batterie s in
the interior are low and
need to be replaced.
Network Information
ZWave System Notes
This product i s a security enable d ZWave Plus product and must be u sed with a Security
Enabled ZWave controlle r to be fully utilized. ZWave is a “Wire less mesh networ k,” and
results may vary b ased on building co nstruction and comm unication path.
To assure interoperabi lity, each ZWave product must pass a s tringent conformance te st to
assure that it me ets the ZWave standard for comple te compliance with all oth er devices and
controls. The ZWave iden tity mark assures cons umers, integrators , dealers and manuf acturers
that their produ cts will reliably per form with any other ZWave device. And , regardless of the
vendor, always powered n odes may act as a repeate r for Kwikset/Weiser/Ba ldwin products.
ZWave Coniguration an d Association Param eters are available on
the Kwikset Conver t page at www.kwikset .com.
Removing the lock from the network
Follow your smart h ome system’s instructi ons
to remove the lock from t he network. When
prompted by the sys tem, press button A” on the
lock interior once.
Please allow time for the con troller to add the lock.
ZWa ve
Controller
12"
305 mm
4. Initiate the proc ess to add the lock to your system
at your smart home co ntroller. Refer to your smart
home system instruct ions for more information.
5. Whe n prompted by your smart home syste m to add the
lock, press but ton “A” on the lock interior one tim e. The
red LED will illuminate when th e lock enters Add Mode.
6. Once succes sful, re-name the lock in your
system (if applica ble). Then, reinstall the
lock interior on the inte rior assembly.
ZWa ve
Controller
12"
305 mm
Loading...