Kwikset Aura Installation And User Manual

67375 002
Rev 02

Parts List

ENGLISH

Installation and User Guide

Required tools

Ruler

Additional Tools (depending on application)

Hammer Wood block Chisel

Prepare the door and check dimensions

1

Phillips head screwdriver

Kwikset

1-800-327-5625

www.kwikset.com

Mounting
Plate

Batteries

Latch A

Latch B

“B” is not i ncluded.
If needed, please contact
Kwikset to orde r a drive-in
latch for your l ock.

Adapter
Ring

Keys

Exterior Assembly

For Latch / Strike

Strike

46780

03809

If drilling a new door, use the supplied template and the complete

door drilling instructions available at kwikset.com/doorprep

Interior Assembly

For Lock

SmartKey

Too l

49191 64109 68611

48654

Make sure your door is compatible. If you have a standard deadbolt mounted

A

separately from the handle below it, your door is compatible.

Compatible Not Compatible

Rim
Lock

Measure to conirm that the hole in the door is either

C D E F

21/8" (54 mm) or 11/2" (38 mm).

21/8"

54 mm

or

11/2"

38 mm

Install the latch and strike

2

Note: Add itional door
prepara tion may be
require d for doors with
11/2" ( 38 mm) holes .
Consul t the deadbolt
drilling instructions at
kwikset.com/doorprep

For

Latch / Strike

Bag

Not CompatibleNot Compatible

Mortise
Lock

Measure to conirm that the backset is
either 23/8" or 23/4" (60 or 70 mm).

backset

23/8" o r 23/4"

60 or 70 mm

(2x) (2x)

(2x) (2x)

03809

Integrated
Interior

Measure to conirm that the hole
in the door edge is 1" ( 25 mm).

25 mm

actual size

46780

1"

Remove your existing deadbolt

B

from your door.

Measure to conirm that the door is between
13/8" and 2 " (35 mm and 51 mm) thick.

35 – 51 mm

13/8 " –2"

actual size

Is the door edge chiseled?

A B

YES

chiseled

Use latch “A”. If the
latch bolt is not already
extende d, extend the
latch bolt as shown.

A

or

NO

not
chiseled

Use latch “B” (not
included). If the latch
bolt is not already
extende d, extend the
latch bolt as shown.

B

face lush against the door edge.

A

Is the D-shaped hole centered in the door hole?

C

YES

or

D-shaped hole D-shaped hole

No adjustment is required.
Proceed to next step.

Rotate latch face as
shown to extend latch.

A

B

NO

Which latch are you installing?Hold the latch in front of the door hole, with the latch

D

Latch “A” Latch “B”

UP is

on top.

A

03809*

(2x)

*Use longer
screws if
holes are
worn out.

Install the strike on the door frame.

E

Make sure the hole in the door frame is drilled a

minimum of 1" (25 mm) deep.

or

B

or

or

UP is

on top.

wood
block

1 / 4

Longer screws
install closest to

B

the door jamb.

46780

(4x)

door frame

Install the exterior keypad

3

For

Lock

Bag

48654

(2x)

actual size

What is the diameter of the hole in the door?

A

Diameter is 21/8"

Diameter is 11/2"

(54 mm)

or

21/8"

54 mm

Adapter Ring is required
for installation. Install on
Exterior Assembly.

Locate the screws for step 3D and keep them within reach.

B

48654

(2x)

38 mm

Adapter Ring is not
needed for installation
and may be discarded.

(38 mm)

11/2"

Install the exterior keypad and mounting plate.

D

a

The cable goes
underneath the latch.

c

Keep parallel to the

edge of the door.

b

Suppor t the exterior
assembly during mounting
plate installation.

G

Route the cable
through the center
hole, then push it into
the bottom hole.

d

Remove the mounting plate from the interior assembly.

C

48654

(2x)

Tighten screws
eve nly. DO NOT ove r
tighten screws.

Install the interior assembly

4

Ensure the turnpiece shaft is pointing up, and remove the interior cover and

A B

battery pack from the interior assembly.

a

Remove the interior
cover from the
interior assembly.

b

Make sure turn
piece shaft is
rotated as shown.

Install the interior assembly onto the mounting plate.

a

b

Insert the key and
test the latch. If the
latch does not
extend or
retract
smoothly, adjust
the screws.

Remove the key
when inished,
and make sure
the latch bolt is
fully extended.

For

Lock

Bag

49191

actual size

(2x)

c

If the turnpiece shaf t is pointing
down, place the cover back onto
the interior assembly and rotate the
turnpiece until you hear it click. You
may need to apply some force.
Once the turnpiece shaft is correctly
oriented, remove the cover again.

Incorrect:

If turnpiece shaft is not oriented
correctly, put the cover back on and
rotate the turnpiece as shown in step C .

d

Do not install

batteries

until step 5.

Ensure tight cable
connection.

c

align

Lay the excess cable
lat inside the bottom of
the interior housing.

d

49191

(2x)

bottom

hole

Ensure you are u sing

the correc t screws.

Using inco rrect

screws will d amage

the produc t.

2 / 4

Install the batteries and perform the door handing process

5

This step will teach your lock the orientation of your door and is crucial to lock operation.

Install 4 AA batteries in the battery pack. With the door open, install the battery

A B C

pack to initiate auto-handing.

D

Ensure correct polarity.

For best results, use
new, non-rechargeable
Alkaline batteries only.

The latch will retract and extend to learn the orientation of the door.

If the bolt does not move,
make sure the batteries
are correctly installed, and
perform step 5B again.

Note: The latch
bolt will only
retract half way.

The Status LED will indicate success or failure.

Green: Door handing was
successful. Proceed to next ste p.

Red: Door handing was
unsuccessful. Make sure the lock
interior and batteries are correctly
installed. Perform step 5B again.

If the door handing process is
still unsuccessful after a second
attempt , see the Manual Door
Handing section on page 4.

Test the lock and check door alignment

6

With the door open, insert the key to

A

extend the latch. Ensure that the latch
extends smoothly.

If your door does not lock and unlock smoothly, make sure you replaced your previous latch and strike with those supplied in the box.

If you still experience locking errors, call Kwikset Support to order a Warped Door Service Kit.

Kwikset Support: 18003275625

Turn the key 180° to retract the latch.

B C D

Ensure that the latch
retracts smoothly.

Close the door. Insert and rotate
the key to lock the door. Ensure
that the door locks smoothly.

Turn the key 180° to retract the latch.
Ensure that the door
unlocks smoothly.

Install the interior cover

7

Important Information about the interior cover

The window on
the interior cover
is unlocked by
default for easier
access to the
battery pack
and buttons.

window

For additional
security, you
may choose to
lock the window
by installing the
security screw.

68611

(1x)

Ensure you are u sing
the correc t screws.

Using inco rrect
screws will
damage the product.

Cover Installation Battery Pack Access

a

Install cover.

Note: You may
need to rotate
the turn piece
to align with the
turn piece shaft.

turn piece

turn piece

shaft

b

Install
screws.

64109 (3x)

Ensure you are u sing
the correc t screws.

Using inco rrect
screws will
damage the product.

If the window is
unlocked, slide
up the window
to access the
battery pack.

For

Lock

Bag

When the window
is locked, you will
need to remove
the entire interior
cover and screws to
access the battery
pack and buttons.

If the window
is locked,
remove the
interior cover
and screws
to access the
battery pack.

actual size

(1x)

(3x)

6410968611

actual size

8

Download the app and create an account

The Kwikset app is needed to use this lock. If
this lock was professionally installed (or installed
by someone other than the homeowner), make
sure this step is performed by the homeowner.

Download the

A

Kwikset app by scanning
the QR code or visiting
www.kwikset.com/app
on your smartphone.

3 / 4

Create your account and follow the setup

B

instructions in the Kwikset app.

Reference Guide

SmartCode at a Glance

Exterior

Lock

Keypad

SmartKey

tool hole

button

Keyway

Tip: To light up the keypad
while the door is locked,
press the Lock button before
entering your user code.
The keypad will not light up
if the door is unlocked.

Status LED colors

These features can be adjusted in some smart home apps.

Interior (cover removed)

Battery
pack

Button “A” Button “B”

Program
Button

Status

LED

Tur n
piece
shaft

System Alerts

Alert Reason Solution

Keypad lashes red once with
one beep*.

Keypad lashes red three
times with three beeps*.

Keypad lashes red 15 times
with 15 beeps*

Keypad lashes red with fast
beeping sound for three to
four seconds.

Keypad lashes red with
continuous beeping sound
for two seconds.

Lock beeps continuously.

*Beeping sounds will only be heard if Lock Sounds have not been disabled in the app.

One incorrect code entered. Re-enter code.

No user code programmed. Program at least one user code.

Three incorrect codes entered.

Low battery. Replace batteries.

Door jammed while attempting
to lock.

Interior assembly is
disconnected from exterior.

Re-enter code after 60 second keypad
lockout.

Manually re-lock door. If needed,
reposition strike.

Remove battery pack, reconnect the interior
to the exterior, then reinstall battery pack.

Manual Door Handing

If needed, the door handing process can be initiated manually. This is useful if the lock is being
moved to a diere nt door.

Color Lock Status

Green (solid) Action successful

Green (blinking) Unlocked

Red (solid) Door handing process unsuccessful

Action unsuccessful or incomplete

Low battery

Status
LED

Red (blinking)

Blue (solid) Bluetooth Pairing successful

Blue (blinking) Bluetooth Pairing Mode

Amber (solid) Entering Network Reset mode

Network or System Reset mode.

Amber (blinking)

Action required.

Locked

Network Reset

Network Re set will delete all Bluetooth pairings, user associations,
and remove the lock from the account.

1 Press and HOLD

“A” for 10 seconds.
You will hear 1 short
beep and see an
amber LED.

Note: After 3

seconds, you will
hear 1 short beep
and see a blue
LED. You should
continue to hold “A”
to enter network
reset mode.

3 Press and release the

Program button to
conirm network reset.

Program

button

The Progr am button must be
presse d within 10 secon ds of
releas ing "A" or the function
will time o ut.

2 Release “A.”

You will see a
blinking amber

10s

LED to indicate
it is in network
reset mode.

4 If successful, you will hear 1 long

beep and see a green LED. If
unsuccessful, you will hear 5 rapid
beeps and see a blinking red LED. If
unsuccessful, repeat from step 1.

Successful:

green
LED

Unsuccessful:

Status
LED

red
LED

1 Remove batte ry pack. 2 Press and HOLD

3 Press the Program button once more. 4 The latch bolt will extend and retract to

System Reset

System Reset will delete all access codes and lock settings including
lock handing. The lock will run the handing process at the end of the
System Reset.

1 Press “A” 10

times. You will
hear 1 short
beep and see a
blinking amber
LED to indicate
it is in system
reset mode.

3 If successful, you will hear 1

long beep and see a green
LED, and the reset process
will begin. During the reset
process , the LED will blink
green/red a few times and
will beep when complete.

If unsuccessful, you will
hear 5 rapid beeps and
see a blinking red LED. If
unsuccessful, repeat from
step 1.

2 Press and release

the Program
button to conirm
system reset.

Program

button

Successful: Unsuccessful:

green
LED

red
LED

the Program button
while reinserting
the battery pack.
Release the
Program button
after 3 seconds.
The status LED will
lash red and green.

learn the orientation of the door. The LED
will lash green if handing is successful
or red if handing is unsuccessful.

Status
LED

Factory Reset

Factory Reset will delete all Bluetooth pairings, user associations,
remove the lock from the account and reset all lock settings
including handing.

1 Remove

battery pack.

3 Press the Program button

once more. The LED will
lash green and red, and
the auto-handing process
will begin.

2 Press and HOLD

the Program button
while reinserting
the battery pack.

Keep holding

the button for
30 seconds until
the lock beeps
and the status
LED lashes red.

4 The latch will retract and

extend to learn the orientation
of the door. The LED will
lash green if auto- handing
is successful or red if auto­handing is unsuccessful.

Status
LED

Troubleshooting

A complete Aura Bluetooth Keypad

Programming and Troubleshooting Guide is available at

www.kwikset.com/aura/support

SmartKey Re-Keying

Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.

Note: If Auto -Lock is enabled, remove the battery pack before
re-keying your lock.

4 / 4

Important Safeguards

1. Read all instructions in their entirety.

2. Familiarize yourself with all warning
and caution statements.

3. Remind all family members of safety precautions.

4. Protect your user codes.

5. Dispose of used batteries according to local laws and
regulations.

WARNING: This Manufacturer advises that no lock

can provide complete security by itself. This lock may
be defeated by forcible or technical means, or evaded
by entry elsewhere on the property. No lock can
substitute for caution, awareness of your environment,
and common sense. Builder’s hardware is available in
multiple performance grades to suit the application.
In order to enhance security and reduce risk, you
should consult a qualiied locksmith or other security
professional.

© 2019 Spectrum Brands, Inc.