Kwikset 61063/01 User Manual

61063 / 01

Parts in the Box

Latch and Strike Exterior Assembly Interior Assembly

M

ENGLISH

Installation and User Guide

Required Tools

Ruler

Additional Accessories
(depending on application)

Hammer Wood block

Prepare door and check dimensions

1

If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.

Phillips Head Screwdriver

You can view the
Kevo installation video
online by scanning
the code to the right
or by visiting
www.kwikset.com/
kevo/support

A

A2

B

E

F

K

L

C

D

G

N

P

H

Q

Kevo Fob

S

R

J

Measure to con rm that the hole in the door

A

is either 2-1/8" (54 mm) or 1-1/2" (38 mm).

2-1/8"

54 mm

or

1-1/2"

38 mm

Note: Additional door preparation may be
required for doors with 1-1/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep.

Install latch and strike

2

Measure to con rm that the backset is either

B

2-3/8" or 2-3/4" (60 or 70 mm).

2-3/8" or 2-3/4"

60 or 70 mm

Measure to con rm that the hole in the door

C

edge is 1" (25 mm).

1"

25 mm

Measure to con rm that the door is either

D

1-3/8" or 1-3/4" (35 mm or 44 mm) thick.

1-3/8" or 1-3/4"
35 mm or 44 mm

Is the door edge chiseled?

A

Use latch “A”. Extend
the latch bolt as shown.

YES NO

or

chiseled

Use latch “A2”. Extend
the latch bolt as shown.

A A2

not
chiseled

Hold the latch in front of the door hole, with the latch face  ush

B

against the door edge.

A2A

Are the latch holes centered in the door hole?

C

YES NO

or

No adjustment is required.
Proceed to next step.

Rotate latch face as
shown to extend latch.

A

180°

Which latch are you installing?

D

Latch “A” Latch “A2”

Install strike on the door frame.

E

or

A2

A

C (2x)

A2

wood
block

A2

D (2x)

180°

B

door frame

Install exterior assembly

3

What is the diameter of the hole in the door?

A

Diameter is 2-1/8" (54 mm). Diameter is 1-1/2" (38 mm).

2-1/8"
54 mm

“F” is required for installation.
Install “F” on “E”.

F

What is the thickness of your door?

B

Door is 1-3/8" (35 mm) thick. Door is 1-3/4" (44 mm) thick.

Use the shorter, silver screws.

E

1-3/8"
35 mm

or

or

1-1/2"

38 mm

“F” is not needed for installation.
Discard “F”.

F

1-3/4"
44 mm

Use the longer, gold screws.

Install exterior assembly and mounting plate.

C

a

Locate mounting plate (K).
Note: It may be on the back of
the interior assembly (L)

b

Cables go underneath latch.

c

d

L

K

K

E

Route cables
through center
hole, then
push cables
into side hole.

Keep parallel
to edge of door

side hole

center

hole

Q/R (2x)

Tighten
screws evenly

e

QR

Q/R

Insert key and test latch. If latch
does not extend or retract smoothly,
adjust screws (Q/R).

G

Remove key when nished and
make sure the latch bolt is fully
extended.

Install interior assembly

4

Remove battery cover and battery pack from interior assembly.

A

a

b

c

Connect the thinner cable.

B

CAUTION: Handle
cables with care
to avoid cable
damage. Do not

Make sure turnpiece is

L

in the vertical position.

pull or use force.

L

Remove

N

interior cover.

Connect the thicker cable.

C

Ensure tight cable connection.

L

M

Remove
battery pack

Properly route cables and install interior assembly.

D

a

d

Route the thinner cable
around the outside of the
thicker cable’s square
connector.

torque
blade

Do not install
batteries yet.

b

turnpiece
shaft

Tuck the thinner cable’s

Tuck cable here
Inserte el cable aquí
Insérez le câble ici

Push the turnpiece shaft
onto the torque blade.

Avoid pinching the excess
thinner cable by pulling it
away from the torque blade.

connector behind the
backplate (as indicated
by the sticker on the
interior assembly).

L

c

e

Ensure tight cable connection.

Lay thicker cable
at against the
interior housing.

S (2x)

Note: Turnpiece may
not rotate smoothly
until after step 5.

Perform door handing process

5

This step will teach the lock the orientation of your door and is crucial for lock operation.

Install 4 AA batteries in the battery pack.

A

P (4x)

M

Ensure correct polarity. For best results,

use new, non-rechargeable Alkaline
batteries only.

Wake up and test Kevo fob

6

Make sure the door is open. Insert the

B

battery pack while pressing and holding the
Program button. Release the button when
the battery pack is all the way inside the lock
interior.

M

The Status LED will  ash red and green,

C

and the lock will beep. Press and release
the Program button again. The latch bolt will
retract and extend on its own.

status LED

Did the latch bolt bolt retract and extend on

D

its own?

YES NO

Door handing process
was successful!
Proceed to next step
after latch bolt stops
moving.

or

Remove battery pack,
wait 15 seconds,
then attempt the
process again.

Press and release the enroll button on the fob

A

with a ballpoint pen to wake it up. When the
fob’s LED  ashes green, the fob is awake and
ready for use.

LED

enroll button

Bring your fob and standard key outside with

B

you and close the door. Make sure there is a
clear line of sight between the lock and the
fob. Touch the deadbolt rose.

deadbolt rose

The light ring will spin blue, then  ash amber

C

once and you will hear one beep. The door
will lock.

J

Note: The deadbolt rose is the metallic
surface behind the light ring.

Download the app and set up your smartphone

7

Download the Kevo app at www.kwikset.com/

A B C

kevo/app or scan the QR code below.

Follow the instructions inside the app to create
an account, enroll your  rst smartphone and send
eKeys to family and friends.

When using your phone to lock and
unlock the door, make sure the phone is
on, Bluetooth is enabled, and the Kevo
app is running in the background.

You may hold the phone in your hand,
pocket, bag or purse as long as there
is a clear line of sight between the lock
and the phone.

Press the deadbolt rose to lock and
unlock the door.

Touch the deadbolt rose again. The light ring

D

will spin blue, then  ash green twice and you
will hear two beeps. The door will unlock.

If your fob is unable to communicate with the
lock, see the online Troubleshooting Guide at

www.kwikset.com/kevo/support.

Re-key the lock (if needed) and install the battery cover

8

Re-key the lock (if needed).

A

a

IMPORTANT: Remove battery
pack before re-keying.

M

b

Re-key the lock to work with
your existing key. See the
supplied SmartKey Re-key
instructions for more
information.

c

Reinstall battery pack.

H

L

M

Install battery cover.

D

N

L

Kevo Reference Guide

Kevo at a Glance

1. Deadbolt rose

2. SmartKey
tool hole

5. Reset button

6. Back panel

7. Program
button

8. Turnpiece

Switches

3. Light ring

4. Keyway

9. Calibrate
button

10. Switches

11. Status LED

Kevo-Compatible Devices

Smartphones and Smart Devices

1. Touch Kevo anywhere on the
metallic surface behind the
light ring to lock and unlock.

2. Insert your SmartKey tool
here when rekeying your lock
to work with your existing key.

3. Changes color to
communicate with you.

4. Insert your standard key here.

5. Only use to reset Kevo
to delete all eKeys and fobs.
See “System Reset” for more
information.

6. Where all the programming
features are located.

7. Use to enroll phones and fobs.

8. Use to manually lock and
unlock Kevo from the inside.
When the turnpiece is vertical,
Kevo is locked. When it is
horizontal, Kevo is unlocked.

9. Use to manually calibrate
phones and fobs.

10. Use to enable and disable the
Status LED, Triple Touch Lock
and Audio.

11. Communicates whether the
door is locked or unlocked
and  ashes red for a low
batter y alert. Can be turned
on and off by Switch #1.

A Kevo-compatible smartphone (or other mobile
internet-connected device or tablet) must have
Bluetooth Smart Ready/ Bluetooth 4.0 and an app
speci c to the device must be installed. Find out if
your device is compatible at www.kwikset.com/

kevo/devices.

Kevo Fob

A Kevo Fob is a Bluetooth device that provides the same
touch-to-open convenience as a smar tphone.

Additional fobs can be purchased as needed. Up to eight
fobs can be enrolled in a single Kevo lock. A single fob
can be enrolled in up to 25 different Kevo locks.

Note: You may choose to use only Kevo fobs, only
smartphones or a mix of both in your Kevo system.

Standard Key

Always make sure you have access to your standard key.

Triple Touch Lock Advanced Features

1234

ON OFF

Switch 1

Status LED

Door lock status LED blinks every 6
seconds. ON position is factory default.

Switch 2

Triple Touch Lock

See “Triple Touch Lock.”
OFF position is factory default.

Switch 3

Audio

Beeping sound is heard during
programming and normal operation.
ON position is factory default.

Switch 4

Future Feature

This is a convenient feature that allows you to lock the door from the
outside without the use of a smar tphone or fob.

You might use Triple Touch Lock if you are using only a standard key in
your system but wish to lock the door by touch, if your smartphone or
fob is disabled, or if you have a visitor in your home that will leave and
lock the door behind them.

Note: This feature is OFF by default. To enable it,  ip Switch #2 to the
ON position, then lock or unlock the door by touching the deadbolt rose.

To lock the door with this feature, touch the deadbolt rose three times,
pausing brie y between each touch. The light ring will spin blue,  ash
amber, and you will hear one beep (if switch #3 is on).

CAUTION: With this feature enabled, it is possible to lock

yourself outside if you don’t have an enrolled smartphone,
Kevo fob or standard key with you.

Inside-Outside
Sensor

The Kevo lock features a sensor
that can tell if your device is
inside or outside your home to
help prevent your door from being
unlocked by unauthorized users
while your device is inside.

Each device in your Kevo system
will automatically calibrate
to enable this sensor as of
software version 1.2.3. For more
information on calibration, go
to www.kwikset.com/kevo/

support.

History Log

A history of the lock’s activity may
be viewed through the Kevo app
or by logging into the web portal:

www.mykevo.com.

Error Notifi cations System Reset

A complete audio/visual chart of all the lights and sounds in the Kevo system is available in the
online Troubleshooting Guide at www.kwikset.com/kevo/support.

Blue Spinning and Shutting Off: Kevo was unable to est ablish
a connection with your device, or Kevo detec ted the device on
the inside of the door. If this happens frequently, see the online
Troubleshooting Guide.

Top Two LEDs are Solid Red: The AA batteries in the Kevo
interior are low and need to be replaced.

WARNING: Reset ting your Kevo system will restore your

lock to factory default settings and delete all smartphones
and fobs from Kevo’s memory.

If you wish to perform a system reset, press and hold the Reset but ton on the
back panel for 10 seconds until the lock beeps and the light ring  ashes red.

Notifi cations

The Kevo app can send
noti cations when the door is
locked and unlocked by eKey
holders. You can choose to
receive the system’s default
noti cations or set up custom
noti cations to monitor a speci c
user or time frame.

Kevo App Passcode

Kevo features an optional,
added-security passcode that
you can enable inside the app to
be used in addition to the app’s
password. Enabling the passcode
will require you to enter a 4-digit
PIN whenever you access the app,
and it protects your Kevo account
against unauthorized changes
when your phone is unlocked.

Magenta Flash: Your device is outside of activation range.
Touch the deadbolt rose again. As of software version 1.2.3,
your device will automatically calibrate so that Kevo's inside­outside sensor adjusts to your device's new location. You may
need to touch the lock a few times for it to learn your device's
new location.

Red Flash: The lock has detected an unauthorized device
within activation range. Kevo will not unlock . If this happens
frequently, see the online Troubleshooting Guide.

Important Safeguards

1. Read all instructions in their entirety.

2. Familiarize yourself with all warning and caution
statements.

3. Remind all family members of safety precautions.

4. Always have access to your lock’s standard key.

5. If using the Triple Touch Lock feature, make sure
to have your smartphone, fob or standard key with
you to prevent locking yourself out.

6. Familiarize yourself with all light ring error
noti cations.

7. Replace low batteries immediately.

Preventing Inadvertent
Unlocking of Your Door

WARNIN G: Failure to follow these safeguar ds

could result in your lock opening inadvertently.

1. Avoid keeping and storing phones and fobs
unnecessarily close to the lock when inside the
home.

2. Restrict access to your Kevo lock’s back panel
and routinely check your settings to ensure they
have not been altered without your knowledge.

Bottom LED is Solid Red: The fob batter y is low and needs
to be replaced. See the online Troubleshooting Guide for
instructions.

Side LEDs Flashing Red: The deadbolt has jammed. Check
your door for alignment and make sure the latch bolt can
operate smoothly.

3. Protect the password to your Kevo app and web
portal accounts.

4. When sending an eKey, always double-check that
you are sending it to the correct recipient.

5. Protect and restrict access to your smartphone so
that your app settings cannot be altered without
your knowledge.

6. Enable the Kevo app’s security passcode so that
your app settings cannot be altered without your
knowledge.

7. When sending eKeys, be aware of the difference
between an Admin user and other users in the
system: an Admin user can send, disable and
delete eKeys.

8. If your smartphone is lost or stolen, use the Kevo
web portal (www.mykevo.com) to disable it.

9. If a fob in your Kevo system is lost or stolen, reset
your lock to delete it from memory.

CAUTION: Prevent unauthorized entry. Because

anyone with access to the back p anel can change your
Kevo lock’s settings, you mus t restrict access to the
back panel a nd routinely check your set tings to ensure
they have not been altered without your knowledge.

CAUTION: As wi th any radio-bas ed technology,

it should be noted tha t the accuracy and reliabilit y
of the Kevo lock’s inside -out side sens or canno t be
guaranteed. Users should not rely solely on the Kevo
lock’s s ensor for se curity pur poses and sh ould always
use caution. Kwikset assume s no responsibilit y for
incorre ct resul ts or damages resul ting from the use of
the Kevo lock’s sensor.

Cert ain home con gurations may impede the Kevo
lock’s sens or more than other s. Example: Your hom e

of ce is located next to your entryway, and part of
the of ce extends past the front door, jutting into the
front yard. If your device is being actively used in that
of ce extension, the Kevo lock’s sensor could possibly
detect the device as being outside of your home while
that device is in active use.

WARNIN G: This M anufac turer advises that no

lock can pr ovide complete security by itself. T his
lock may be defeated by f orcible or technica l means,
or evaded by en try elsewhere on the property.
No lock can substi tute for caution, awareness of
your environment, and common sense. Builder’s
hardware is availa ble in mult iple per formance grades
to suit the a pplication. In order to enhance security
and reduce risk, you should consult a quali ed
locksmith or other securit y professional.

Phones: After a sys tem reset, you will need to re-enroll and your Owner
phone. You will still be able to send eKeys at no charge to anyone who
previously had an active eKey at the time of reset.

Fobs: After a sys tem reset, all fobs will need to be re-enrolled. See the online
Troubleshooting guide for instructions.

Need Help?

If you have questions, our highly trained Kevo Support team can
provide you with the assistance you need:

1-800-327-5625

1-800-327-5625

1800 623 118

0800 736 776

www.kwikset.com/kevo/support

©2014 Kwikset Corporation