Kwikset 264 Contemporary User Manual
66882002
Rev 02
Parts in the box
264 Contemporary
Electronic Deadbolt
ENGLISH
Installation and User Guide
Required tools
Ruler4 AA Batt eries
Additional Tools (depending on application)
Hammer
Prepare the door and check dimensions
1
Phillips screwdriver
Wood
block
Pliers
Kwikset
Technical Support
1-800-327-5625
www.kwikset.com
Latch
A2
A
Exterior Assembly
Interior Cover
J K L M
E
Drive-In Collar
Keys
Latch and
Strike Screws
Strike Cylinder
B C D
Mounting Plate
Interior
Assembly
F G H
Interior Assembly
Screws
Mounting Plate
Screws
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep
Measure to conirm that the hole in
A
the door is either 21/8" (54 mm) or
11/2" (38 mm).
21/8"
54 mm
or
11/2"
38 mm
Note: Additional door preparation may be
required for doors with 11/2" (38 mm) holes.
Consult the deadbolt drilling instructions at
www.kwikset.com/doorprep
Install the latch and strike
2
Measure to conirm that the backset is
B C D
either 23/8" or 23/4" (60 or 70 mm).
23/8" or 23/4"
60 or 70 mm
backset
Measure to conirm that the hole in
the door edge is 1" (25 mm).
1"
25 mm
Measure to conirm that the
door is either 13/8" or 13/4"
(35 mm or 44 mm) thick.
13/8 " or 13/4"
35 mm or 44 mm
Hold the latch in front of the door hole, with
A B C
the latch face lush against the door edge.
A
Is the slotted hole centered in the door hole?
YES
NO
or
slotted hole
is centered
No adjustment is
required. Proceed
to next step.
Rotate latch face as
shown to extend latch.
slotted hole is
NOT centered
180°
Is the door edge chiseled?
YES
chiseled
Install latch in door with
supplied screws.
Optional: Remove square
corner face and replace with
round corner face (if needed).
A
Ensure A2 snaps into place.
Install latch in door with
supplied screws.
NO
or
Use a lathead screwdriver to
lift tabs on collar of rectangular
face to remove it from latch.
Install drive-in collar.
not
chiseled
A
A2
Align tabs with
holes in collar.
Ensure collar
snaps into place.
Pull collar to test
Install latch in door with
wood block and hammer.
B
for tight it.
D
A
Install strike on the door frame.
Make sure hole in door frame is drilled a
minimum of 1” (25 mm) deep.
C
K (2x)
door frame
IM PO RTAN T: Make sure the latch bolt is fully
retracted (in the unlocked position).
unlocked
A
Make sure
slotted hole is at
bottom of latch.
K (2x)
Make sure
slotted hole is at
bottom of latch.
1 / 4
Prepare keypad and mounting plate (only for doors with smaller holes)
3
What is the diameter of the hole in the door?
Diameter is 2-1/8" (54 mm) Diameter is 1-1/2" (38 mm)
21/8"
54 mm
No adjustment is required.
Proceed to step 4.
or
11/2"
38 mm
Remove adapter ring from exterior assembly:
A
E
1. Remove gasket. 2. Remove adapter
Use pliers to remove two tabs from mounting plate:
B
ring from gasket.
3. Reinstall gasket,
ensuring tight seal.
Install exterior assembly
4
Install the cylinder into the exterior assembly.
A
tabs
G
Route the cable below the latch.
B
exterior side
of door
IM PO RTAN T: Make sure the latch is fully
C
retracted (in the unlocked position).
E
unlocked
D
cable
IM PO RTAN T: Make sure the torque
D
blade is in the horizontal position.
horizontal
Secure the mounting plate with the supplied screws.
G
Keep
parallel to
door edge.
M (2x)
Insert the torque blade through the
E
horizontal slot in the latch.
horizontal
slot
Insert the key and test the latch for smooth operation.
H
If latch does
not operate
smoothly,
adjust screws.
Push the torque blade through the center
F
hole in the mounting plate and send the
cable through the bottom hole.
interior side of door
G
torque blade in
center hole
cable in
bottom hole
Remove the key and make sure the latch
I
bolt is still in the unlocked position.
F
unlocked
2 / 4
Loading...