HDSWTH3D-4
Fast Switching HDMI 4X1 with HEAC
INSTRUCTION MANUAL
118 W. Streetsboro Street, Ste. 125 | Hudson, OH 44236 | Toll Free: (866) 865-7737
V.1.2
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fi re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
fl ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualifi ed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports fi rst, then remove the power cable; fi nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifi er service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
Introduction ........................................................................1
Package Contents .............................................................. 1
Features ............................................................................. 2
Specifi cations ..................................................................... 2
Panel Descriptions .............................................................. 3
Connection and Operation ................................................... 4
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
This a fast switching HDMI 4x1 with HEAC,3D function. It supports
4 HDMI inputs and 1 HDMI output. With Built-in HDCP engine for
Instant Port Switching(IPS), 4 Ports switching can be very fast
because there is no need to redo HDCP authentication when
port switching occurs. With the built-in HEC(HDMI Ethernet) and
ARC(Audio Return Channel) chips, it can split HEC which is from
HDTV to Ethernet signals, and can split ARC which is also from
HDTV to Coaxial, Toslink, Stereo audio signals which are also
from source device through ARC ON/OFF button on the Remote
Control.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for suffi cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging
and make sure the following items are contained in the shipping
carton:
• HDSWTH3D-4 HDMI Switcher
• Remote Control
• 5V/2A DC Power Supply
• Users Manual
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer fi le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 2011. All Rights Reserved.
Version 1.2 JUNE2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & SPECIFICATIONS
FEATURES
• Supports 4 HDMI inputs and 1 HDMI output.
• Built-in HDCP engine for Instant Port Switching(IPS), 4 Port switching can be very fast because there is no need to redo HDCP
authentication when port switching occurs.
• Supports Audio Return Channel (ARC) from (sink) device. Connect ARC port to Amplifi er Receiver. Supports HDMI Ethernet Channel
(HEC) from display (sink) device, connect Ethernet port to Ethernet devices, such as computer, Router, etc.
• Supports digital audio T oslink and COAX output simultaneously and Stereo audio output from source device. Connect these ports to
Amplifi er Receiver.
• Supports 3D all format, including 1080p@23.98/24Hz, 720p@59.94/60Hz/50Hz, bandwidth up to 225MHz.
• Supports Consumer Electronic Control (CEC).
• Supports highest video resolution 1080p.
• Supports 225MHz/2.25Gbps per channel (6.75Gbps all channel) bandwidth.
• Supports 12bit per channel (36bit all channel) deep color.
• Supports uncompressed audio such as LPCM.
• Supports compressed audio such as DTS Digital, Dolby Digital (including DTS-HD and Dolby True HD)
* ARC function only works if your display device supports ARC. Check you user’s guide.
NOTE: HEC also goes by the name HEAC (HDMI Ethernet Audio Control)
SPECIFICATIONS
Signal Inputs/Output:
• Input DDC Signal: 5 volts p-p (TTL)
• Input and Output Signal: HDMI(with HEAC,3D)
• Output Audio Signal: Toslink, Coaxial, Stereo
Operating Frequency:
• Vertical Frequency Range: 50/60Hz
• Video Amplifi er Bandwidth: 2.25Gbps/225MHz
Resolutions(HDTV):
• Interlaced (50&60Hz): 480i,576i,1080i
• Progressive (50&60Hz): 480p,576p,720p,1080p
Mechanical
• Size (LxWxH): 10.16 x 4.4 x 1 in (258 x 112 x 26mm)
• Weight (Net): 1.6 lbs /0.73KGs
Warranty
• Limited Warranty: 1 Year Parts and Labor
Environmental
• Operating Temperature: 32°F to 158°F / 0°C to +70°C
• Operating Humidity: 10% to 80 % RH (no condensation)
• Storage Temperature: 14°F to 176°F / -10°C to +80°C
• Storage Humidity: 5% to 90 % RH (no condensation)
Power Requirement
• External Power Supply: 5V DC @2A
• Power Consumption (max): 5 W
Regulatory Approvals
• Converter Unit: FCC,CE,UL
• Power Supply: UL,CE,FCC
Accessories Adapter
• AC Power Adapter: US standard
Note: Specifi cations are subject to change without notice.
2
FRONT PANEL
BACK PANEL
PANEL DESCRIPTIONS
Ethernet: Connect this port to PC. When HDTV with HEC enable HEC function, PC will be connected to Ethernet.
Audio Port: Connect the three ports to Amplifi er Receiver
When select ARC ON, audio output is from HDTV with ARC.
When select ARC OFF, audio output is from Source devices.
HDMI Output: Connect this port to HDTV
HDMI Input: Connect these ports to source devices
-
DC/5V: Connect this port to Power Supply
Power Switch: Turn on or off the power
Power LED: When the switching is working, LED turns blue; When it is standby, LED turns red;
IR: Receive the signal from Infrared Remote Control.
Input LED: LED will turn on when input port is selected.
-
2CH/5.1CH LED: LED will turn on when 5.1CH button is pressed; LED will turn off when 2CH button is pressed.
Select: Press this button to cycle through the inputs.
ARC ON/OFF LED: LED will turn on when ARC ON button is pressed, then this product will enable ARC function, and audio signal
will be from HDTV; LED will turn off when ARC OFF button is pressed, then ARC function will be turned off, and audio signal will be from
source devices.
Select: Press this button to select ARC on or off.
3
CONNECTION AND OPERA TION
CONNECTION
1. Connect HDMI input of the product to source devices.
2. Connect HDMI output of the product to HDTV.
3. Connect audio port to Amplifi er Receiver.
4. Connect Ethernet port to PC
5. Insert the DC side of 5V power supply into the unit and then connect the AC side of the power supply into the wall outlet.
6. Turn on the power.
OPERATION
1. Source Select: Press “Select” button or remote control to switch Input sources from Input 1 to Input 4 manually.
2. 2CH/5.1CH Audio Output Select
Note: Only when the source supports 5.1CH output (including CD), this function is effective and it realizes through the 2.1CH and 5.1CH
buttons on the remote control. Press “2CH” button, the product outputs 2CH audio and the LED turns off; press “5.1CH” button, the
product outputs 5.1CH audio and the LED turns on. When provided with power, it automatically selects 5.1CH audio output. If the source
can only support 2CH audio output, the “5.1CH” button will become invalid, that is, although you press “5.1CH” button, the product still
outputs 2CH audio and the LED is still on.
3. ARC ON/OFF
When select ARC ON, audio output is from HDTV display with ARC.
When select ARC OFF, audio output is from Source device.
Attention: Insert / Extract cable gently.
CONNECTION DIAGRAM
4
TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER KVM SWITCH TECH, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to KVM SWITCH TECH,
Inc. at the return address set forth on the Product’s packing label at your expense. KVM SWITCH TECH, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You
are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty
pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you
and you agree to indemnify and hold harmless KVM SWITCH TECH, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to KVM SWITCH TECH. Any intellectual property rights pertaining to the Product
are licensed to you by KVM SWITCH TECH, Inc. and/or its affi liates, including any manufacturers or distributors of the Product (collectively, “KVM SWITCH TECH”) for
your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by KVM SWITCH TECH for your personal use only. KVM
SWITCH TECH does not transfer either the title or the intellectual property rights to the Product and KVM SWITCH TECH retains full and complete title to the intellectual
property rights therein. All trademarks and logos are owned by KVM SWITCH TECH or its licensors and providers of the Product, and you may not copy or use them in
any manner without the prior written consent of KVM SWITCH TECH, which consent may be withheld at the sole discretion of KVM SWITCH TECH.
The functionality and usability of the Product is controlled by KVM SWITCH TECH, Inc. from its offi ces within the State of Texas, United States of America. KVM
SWITCH TECH makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address
you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
KVM SWITCH TECH may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT W ARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. KVM SWITCH TECH DOES NOT WARRANT
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESUL TS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
KVM SWITCH TECH has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not
be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies
or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, KVM SWITCH TECH DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED W ARRANTIES OF MERCHANTABILITY, FITNESS FOR A P ARTICULAR PURPOSE AND NON-INFRINGEMENT. KVM
SWITCH TECH DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT . KVM
SWITCH TECH DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
KVM SWITCH TECH WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT KVM SWITCH TECH) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
KVM SWITCH TECH.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL KVM SWITCH TECH BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF KVM SWITCH TECH OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL KVM
SWITCH TECH’S TOTAL LIABILITY T O YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED
THE AMOUNT YOU PAID TO KVM SWITCH TECH, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
5
Loading...