Page 1
IP AutoSwitch
Figure 1: IP AutoSwitch
Figure 2: Serial Number and Master Select Button
Installation Instructions
Technical Su pp or t
If you need technical assistance, please contact KVH Technical Support:
North/South America, Australia, New Zealand:
Phone: +1 401 847-3327
E-mail: support@kvh.com
These instructions explain how to add an
IP AutoSwitch to a TracVision® TV-series system.
Step 1 - Inspect Parts
Follow these steps to inspect the kit contents.
a. Unpack the box and ensure it contains one each
of the following items:
• 3 ft (1 m) Ethernet cable
• 2 ft (60 cm) RF cable
• Adhesive-backed Velcro strip
b. Carefully examine all of the supplied parts to
ensure nothing was damaged in shipment.
c. Locate the serial number on the bottom of the
IP AutoSwitch (see Figure 2) and record it in the
space below. You will need this number later.
S/N
Europe, Middle East, Asia, Africa:
Phone: +45 45 160 180
E-mail: support@emea.kvh.com
Bottom View
Step 2 - Choose a Mounting Location
Choose a mounting location that meets the
following requirements:
• Dry, well-ventilated, and away from heat
sources
•Provides a clear view of and easy access to the
Master Select button (see Figure 2)
•Provides adequate clearance for running the
cables and allows for service loops and strain
relief
• Within 2 ft (60 cm) of the associated receiver in
order to use the supplied cable
•Either a horizontal or vertical surface
KVH and TracVision are registered trademarks of KVH Industries, Inc.
All other trademarks are property of their respective companies. The information in this document is subject to change without notice.
No company shall be liable for errors contained herein. © 2014 KVH Industries, Inc., All rights reserved. 54-1023 Rev. B
Serial Number
Master Select Button
1
Page 2
Step 3 - Wire the IP AutoSwitch
Figure 3: IP AutoSwitch Connections
Connect up to 3 IP AutoSwitches
4 3 2 18 7 6 5
POE
48V
+
Switch
** Network Connections
Using the supplied Ethernet cable, connect the IP AutoSwitch
to the onboard network. If you do not have a network, install
a router or router and switch as shown below.
Connect up to 7 IP AutoSwitches
OR
Router
12VDC
POWER
ResetEthernet Internet4321
AC Power
Connect up to 2 IP AutoSwitches
Router
12VDC
POWER
ResetEthernet Internet4321
To TV-Hub
AC Power
AC Power
TV-Hub
Receiver
AC Power
Satellite In
IP AutoSwitch
To R e ce i ve r
RF In
Network
* Varies depending on your system configuration
(see your TV-Series Installation Guide for details)
To N e tw o rk * *
RF Input*
The wiring of the IP AutoSwitch depends on the
specific configuration. Refer to the Installation
Guide for complete wiring diagrams, while
following the general wiring steps below:
a. Disconnect the RF input cable from the receiver
and connect it to the RF In jack on the IP
AutoSwitch. Then tighten the hex nut to 15 in.lbs of torque.
b. Connect the supplied 2 ft (60 cm) RF cable from
the To Receiver port on the IP AutoSwitch to
the receiver’s satellite input and tighten the hex
nut to 15 in.-lbs of torque.
c. Using the supplied Ethernet cable, connect the
Network port of the IP AutoSwitch to the
onboard network. If a network is not available,
install a router as shown in Figure 3.
d. If not already connected, connect the TV-Hub to
the onboard network (see Figure 3).
e. Using the supplied Velcro strip, secure the
IP AutoSwitch to the mounting surface.
2
Page 3
Step 4 - Connect to the Web Interface
Figure 4: Add IP AutoSwitch Screen
Figure 5: IP AutoSwitch LED Status Indications
LED Color Indication
Orange Registered with the system but
not currently the master
Orange,
flashing
Initializing
Red Error:
•unable to communicate with
the system,
•network is not detected, or
•unable to register
Green Registered with the system
and currently the master
Choose one of the following methods to connect to
the TV-Hub’s web interface:
•Using any Wi-Fi-enabled mobile device (such as
a smartphone, tablet, or laptop), select the
TV-Hub-<TV-Hub serial number> network
from your device’s Wi-Fi settings. Then start
your web browser and enter http://tvhub.kvh.
•Connect your computer to the onboard network
and enter the TV-Hub’s IP address in your web
browser. (The IP address can be found on the
Settings page of the web interface.)
Step 5 - Configure the IP AutoSwitch
Follow these steps to configure the IP AutoSwitch.
NOTE: KVH recommends that you run the Setup
Wizard in the web interface whenever you change your
system’s configuration by adding or removing devices.
a. At the AutoSwitch page of the web interface,
select Add IP AutoSwitch (Figure 4).
b. Enter the serial number and a friendly name for
the IP AutoSwitch (for example, “Salon”).
c. Select Save to save changes.
Step 6 - Select a Master Receiver
Any receiver connected to an IP AutoSwitch can
become the master receiver for the system. The
master receiver controls satellite selection.
Important!
The TV-Hub has a built-in IP AutoSwitch. Any
receiver connected directly to the TV-Hub can
therefore be selected as a master receiver through
the web interface.
a. To choose a master receiver, select it at the
Home page of the web interface, or press the
Master Select button on the associated
IP AutoSwitch.
b. Verify that the LED in the Master Select button
on the IP AutoSwitch is lit green (see Figure 5).
The LEDs for any other IP AutoSwitches should
be lit orange.
The installation procedure is complete!
3
Loading...