Kvaser USBcan Light 4xHS User’s Guide
Copyright 2015-2018 Kvaser AB, Mölndal, Sweden
http://www.kvaser.com
Printed Wednesday 16thMay, 2018
We believe that the information contained herein was accurate in all respects at the time of printing.
Kvaser AB cannot, however, assume any responsibility for errors or omissions in this text. Also note
that the information in this document is subject to change without notice and should not be construed
as a commitment by Kvaser AB.
Kvaser USBcan Light 4xHS User’s Guide 2 (20)
(This page is intentionally left blank.)
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 3 (20)
Contents
1 About this manual 4
2 Introduction 5
2.1 Welcome to Kvaser USBcan Light 4xHS . . . . . . . . . . . . . . . . 5
2.2 Major features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Additional software and documentation . . . . . . . . . . . . . . . . 6
3 Kvaser USBcan Light 4xHS hardware 7
3.1 Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 USB connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 CAN channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Appendices 10
4.1 Definitions of LED states and colors . . . . . . . . . . . . . . . . . . 10
4.2 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 CAN connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 CAN bus termination . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.5 Updating the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Disposal and Recycling Information 16
6 Legal acknowledgements 17
6.1 Usage warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.2 EU Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . 18
6.3 Patents, Copyrights and Trademarks . . . . . . . . . . . . . . . . . . 19
7 Document Revision History 20
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 4 (20)
1 About this manual
This manual is intended for Kvaser USBcan Light 4xHS users. This document
contains a description of the hardware’s properties and general instructions for
connecting the device to a computer.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 5 (20)
2 Introduction
This section will describe the functions and features of the Kvaser USBcan Light
4xHS.
2.1 Welcome to Kvaser USBcan Light 4xHS
Figure 1: Kvaser USBcan Light 4xHS
Kvaser USBcan Light 4xHS is a small, yet advanced, portable multi channel CAN
to USB real time interface that handles transmission and reception of standard and
extended CAN messages on the CAN bus with a high time stamp precision. The
Kvaser USBcan Light 4xHS is compatible with applications that use Kvaser‘s
CANlib.
This guide applies to Kvaser USBcan Light 4xHS devices listed in Table 1.
Device Product Number (EAN)
Kvaser USBcan Light 4xHS 73-30130-00831-1
Table 1: Kvaser USBcan Light 4xHS devices and their product numbers.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 6 (20)
2.2 Major features
• Low cost USB CAN interface.
• Quick and easy plug-and-play installation.
• Supports both 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers.
• Power is taken from the USB bus.
• 100% compatible with applications written for other Kvaser CAN hardware
with Kvaser CANlib.
• High-speed CAN connection (compliant with ISO 11898-2), up to 1 Mbit/s.
• Fully compatible with J1939, CANopen, NMEA 2000
R
and DeviceNet.
• Simultaneous operation of multiple devices.
• Includes 4 channel breakout cable.
2.3 Interface
Kvaser USBcan Light 4xHS provides a CAN bus interface through a standard USB
interface.
2.4 Additional software and documentation
The Kvaser CANlib SDK includes everything you need in order to develop software
for Kvaser CAN hardware. The SDK contains full documentation and many sample
programs, written in C, C++, C#, Delphi, Python and Visual Basic. All Kvaser CAN
interface hardware share a common software API. Programs written for one device
type will run without modification on other device types.
The latest versions of documentation, software and drivers can be downloaded for
free at www.kvaser.com/download.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 7 (20)
3 Kvaser USBcan Light 4xHS hardware
In this section you can read more about the CAN channels, power supply and LED
indicators.
3.1 Hardware installation
For the Kvaser USBcan Light 4xHS to communicate with the host computer, the
correct version of the Kvaser driver and firmware must be installed.
After the driver has been installed on the host computer, the firmware may then be
downloaded and installed on the Kvaser USBcan Light 4xHS.
The latest version of the driver and firmware can be downloaded from
www.kvaser.com/download.
The driver is installed by running the file
kvaser_drivers_setup.exe
.
The Kvaser USBcan Light 4xHS may be inserted in any free USB socket on the
host computer. You do not need to switch the power off before inserting or
removing the device.
For information on how to upgrade the firmware, see Section 4.5, Updating the
firmware, on Page 14.
3.2 USB connector
The Kvaser USBcan Light 4xHS has a standard USB type “A” connector.
Figure 2: A standard USB type “A” connector.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 8 (20)
Connect the device to your computer using any high quality USB 2.0 certified
cable. The maximum USB cable length is 5 m (∼ 16 ft). If you need a longer cable,
you can use USB hubs or USB extension cables with a built-in hub. By chaining up
to 5 hubs, you can achieve an effective cable length of up to 25 m (∼ 82 ft).
As USB cables become longer they are more sensitive to EMI,
because they make a longer antenna that can pick up more
noise. These issues can be mitigated by using higher quality
cables with better shielding. Thicker cables tend to be better than
thin ones, and braided shielding tends to be more reliable than
only foil. Furthermore, longer cables may introduce signal
degradation and timing issues that, if necessary, can be mitigated
using shorter cable segments combined with hubs that amplify
the signal and handle delays on a per-cable basis.
3.3 CAN channels
The Kvaser USBcan Light 4xHS has four CAN Hi-Speed channels in a single
26-pin HD D-SUB CAN connector (see Figure 3). See Section 4.3, CAN
connectors, on Page 12 for pinout information.
Figure 3: CAN connector on Kvaser USBcan Light 4xHS
3.4 Power supply
The Kvaser USBcan Light 4xHS is powered from the USB port.
3.5 LED Indicators
The Kvaser USBcan Light 4xHS has one power LED and one traffic LED for each
CAN channel as shown in Figure 4 on Page 9. Their functions are described in
Section 4.1, Definitions of LED states and colors, on Page 10.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 9 (20)
Figure 4: LEDs on the Kvaser USBcan Light 4xHS.
3.6 Troubleshooting
Use “Kvaser Device Guide” in the Control Panel to verify that the computer can
communicate with the Kvaser USBcan Light 4xHS. If the firmware version shown is
all zeros, there are communication problems. If the LEDs are not flashing or do not
light up at all, check the power supply.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 10 (20)
4 Appendices
In this section you will find technical information about the Kvaser USBcan Light
4xHS and its connectors.
4.1 Definitions of LED states and colors
A Kvaser device has two basic types of LEDs; Power and Traffic. These are dual
colored as shown in Table 2. A device with multiple CAN channels has one Traffic
LED for each CAN channel. When the device has more than one channel a space
and digit is added on the label, CAN 1, CAN 2 etc. Low cost products, such as
Kvaser USBcan Light 4xHS, are not equipped with any red Traffic LEDs.
LED Label Color
Power PWR Green/Yellow
Traffic CAN Yellow
Table 2: The different type of LEDs.
The following definitions is used to describe the state of an LED:
Off The LED is off and no light is emitted.
Flash The LED is lit up for a very short time. A single flash may be hard to see
and a continuous set of flashes will look the same as On.
Slow Blink The LED is repeatedly turned On and Off. The On and Off phase is
equal in time.
Fast Blink The LED is repeatedly turned On and Off but with a higher frequency
than Slow Blink. The On and Off time is still equal.
On The LED is constantly emitting light.
Slow Waver This is a variant of Slow Blink but instead of being Off, a second color
is On. This is only possible with a dual colored LED.
Fast Waver The LED is alternating between two colors as in Slow Waver but
using a higher frequency.
Running This means that all LEDs are lit, one at the time, in sequence with every
color available i.e. “Power green->Power yellow->Traffic 1 yellow->Traffic 2
yellow->. . .”
As an example, "Slow Waver (Green/Yellow)" means that the LED is slowly blinking
by alternating between green and yellow.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 11 (20)
4.1.1 Interface mode
The device is in Interface mode when connected to the PC via USB. If the Power
LED is showing a steady green light, the device is in Interface mode and working
correctly. When connected to the computer for the first time, the Power LED will
blink slowly in yellow until the driver is installed and the device has received a USB
configuration.
When in Interface mode, if the Power LED is yellow for an extended period,
something is wrong. Please see Table 3.
The power should never be removed when firmware update is in
progress.
Power LED Traffic LED Description
Slow Blink (Yellow) All off (-) Waiting for USB configuration
Slow Waver (Green/Yellow) Slow Blink(Yellow) Firmware configuration error
1
Slow Waver (Green/Yellow) All Slow Blink (Yellow) Power problem
2
Table 3: Yellow Power LED shows problems in Interface mode.
Traffic LED Description
Off (-) Idle, no CAN traffic
Flash (Yellow) CAN message received or sent
All Fast Blink (Yellow) Firmware update is in progress
Table 4: Traffic LED shows CAN bus status in Interface mode .
4.2 Technical data
In Table 5 on Page 12 you will find the Kvaser USBcan Light 4xHS’s technical
specifications.
1
This should not normally happen. If it does, please contact Kvaser support.
2
This indicates low power supply, such as using an unpowered USB hub.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 12 (20)
CAN Channels 4
CAN Transceivers TJA1051T (Compliant with ISO 11898-2)
CAN Controller Kvaser CAN IP in FPGA
Galvanic isolation Yes
CAN Bit Rate 50 kbit/s to 1 Mbit/s
Time stamp resolution 100 µs
Max message rate 8000 msg/s per channel
Error Frame Detection Yes
Error Frame Generation No
Silent mode No
Kvaser MagiSync No
PC interface USB Hi-Speed
Power consumption max 280 mA
Hardware configuration Done by software (Plug & Play).
Software requirements Windows Vista or later. (For other operating systems, contact Kvaser
support.)
Dimensions 50 x 170 x 20 mm for body incl. strain relief
Weight 150 g (300g including HD26-4DS9 Splitter)
Operating temperature −20◦C to +70◦C
Storage temperature −20◦C to +70◦C
Relative humidity 0 % to 85 % (non-condensing.)
Table 5: Technical Specifications.
4.3 CAN connectors
Kvaser USBcan Light 4xHS devices that use the 26-pin HD D-SUB connector (see
Figure 5) have the pinning described in Table 6 on Page 13. This table also
describes how the HD26-4xDS9 splitter (see Figure 7 on Page 14) connects to four
seperate 9-pin D-SUB connectors, CAN 1 to CAN 4.
Figure 5: The male 26 pin HD D-SUB connector pin numbers
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 13 (20)
Figure 6: The male D-SUB 9 connector pin numbers
HD D-SUB CAN 1 CAN 2 CAN 3 CAN 4 Function
1 2 CAN_L channel 1
2 2 CAN_L channel 2
3 2 CAN_L channel 3
4 2 CAN_L channel 4
5 Not connected
6 Not connected
7 Not connected
8 4 Not used
9 Not connected
10 9 Not used
11 7 CAN_H channel 1
12 7 CAN_H channel 2
13 7 CAN_H channel 3
14 7 CAN_H channel 4
15 Not connected
16 Not connected
17 Not connected
18 4 Not used
19 3 GND channel 1
20 3 GND channel 2
21 3 GND channel 3
22 3 GND channel 4
23 Not connected
24 Not connected
25 Not connected
26 Not connected
Table 6: Pin configuration of the 26-pin HD D-SUB (and HD26-4xDS9 splitter)
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 14 (20)
Figure 7: The HD26-4xDS9 Splitter
4.4 CAN bus termination
Every CAN bus must be terminated with a 120 Ohm resistor at each end of the
bus. The Kvaser USBcan Light 4xHS does not contain any CAN bus termination,
because their inclusion could cause severe disturbance in a system which is
already correctly terminated.
For laboratory or testing use, the exact value of the termination resistors is not
always critical. Sometimes a single terminator is sufficient. For production, proper
termination is essential. If you see error frames on the bus, you should check the
termination.
To save yourself a lot of trouble, always terminate the CAN
bus properly.
4.5 Updating the firmware
For the Kvaser USBcan Light 4xHS to communicate with the host computer,
compatible versions of the Kvaser CANlib (including driver) and firmware must be
installed.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 15 (20)
The latest versions of firmware and drivers can be downloaded for free at
www.kvaser.com/download.
Connect the Kvaser USBcan Light 4xHS to your PC with the USB cable and start
the update.exe application. A window opens showing the Firmware Update
Instructions, read and follow those carefully.
To check the current firmware version, open “Kvaser Device Guide” which can be
found in the Control Panel. Select “Kvaser USBcan Light 4xHS” in the tree view to
the left, and click on the channel. The firmware revision information now appears in
the right half of the window.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 16 (20)
5 Disposal and Recycling Information
When this product reaches its end of life, please dispose of it
according to your local environmental laws and guidelines.
For information about Kvaser’s recycling programs, visit:
http://www.kvaser.com/en/kvaser/recycling-policy.html
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 17 (20)
6 Legal acknowledgements
6.1 Usage warning
WARNING FOR ALL USERS
WARNING! - YOUR USE OF THIS DEVICE MUST BE DONE WITH CAUTION AND A FULL
UNDERSTANDING OF THE RISKS!
THIS WARNING IS PRESENTED TO INFORM YOU THAT THE OPERATION OF THIS DEVICE
MAY BE DANGEROUS. YOUR ACTIONS CAN INFLUENCE THE BEHAVIOR OF A CAN-BASED
DISTRIBUTED EMBEDDED SYSTEM, AND DEPENDING ON THE APPLICATION, THE
CONSEQUENCES OF YOUR IMPROPER ACTIONS COULD CAUSE SERIOUS OPERATIONAL
MALFUNCTION, LOSS OF INFORMATION, DAMAGE TO EQUIPMENT, AND PHYSICAL
INJURY TO YOURSELF AND OTHERS. A POTENTIALLY HAZARDOUS OPERATING
CONDITION IS PRESENT WHEN THE FOLLOWING TWO CONDITIONS ARE
CONCURRENTLY TRUE: THE PRODUCT IS PHYSICALLY INTERCONNECTED TO A REAL
DISTRIBUTED EMBEDDED SYSTEM; AND THE FUNCTIONS AND OPERATIONS OF THE
REAL DISTRIBUTED EMBEDDED SYSTEM ARE CONTROLLABLE OR INFLUENCED BY THE
USE OF THE CAN NETWORK. A POTENTIALLY HAZARDOUS OPERATING CONDITION MAY
RESULT FROM THE ACTIVITY OR NON-ACTIVITY OF SOME DISTRIBUTED EMBEDDED
SYSTEM FUNCTIONS AND OPERATIONS, WHICH MAY RESULT IN SERIOUS PHYSICAL
HARM OR DEATH OR CAUSE DAMAGE TO EQUIPMENT, DEVICES, OR THE SURROUNDING
ENVIRONMENT.
WITH THIS DEVICE, YOU MAY POTENTIALLY:
• CAUSE A CHANGE IN THE OPERATION OF THE SYSTEM, MODULE, DEVICE,
CIRCUIT, OR OUTPUT.
• TURN ON OR ACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR FUNCTION.
• TURN OFF OR DEACTIVATE A MODULE, DEVICE, CIRCUIT, OUTPUT, OR
FUNCTION.
• INHIBIT, TURN OFF, OR DEACTIVATE NORMAL OPERATION.
• MODIFY THE BEHAVIOR OF A DISTRIBUTED PRODUCT.
• ACTIVATE AN UNINTENDED OPERATION.
• PLACE THE SYSTEM, MODULE, DEVICE, CIRCUIT, OR OUTPUT INTO AN
UNINTENDED MODE.
ONLY THOSE PERSONS WHO:
(A) ARE PROPERLY TRAINED AND QUALIFIED WITH RESPECT TO THE USE OF THE
DEVICE,
(B) UNDERSTAND THE WARNINGS ABOVE, AND
(C) UNDERSTAND HOW THIS DEVICE INTERACTS WITH AND IMPACTS THE FUNCTION
AND SAFETY OF OTHER PRODUCTS IN A DISTRIBUTED SYSTEM AND THE APPLICATION
FOR WHICH THIS DEVICE WILL BE APPLIED, MAY USE THE DEVICE.
PLEASE NOTE THAT YOU CAN INTEGRATE THIS PRODUCT AS A SUBSYSTEM INTO
HIGHER-LEVEL SYSTEMS. IN CASE YOU DO SO, KVASER AB HEREBY DECLARES THAT
KVASER AB’S WARRANTY SHALL BE LIMITED TO THE CORRECTION OF DEFECTS, AND
KVASER AB HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY OVER AND ABOVE THE
REFUNDING OF THE PRICE PAID FOR THIS DEVICE, SINCE KVASER AB DOES NOT HAVE
ANY INFLUENCE ON THE IMPLEMENTATIONS OF THE HIGHER-LEVEL SYSTEM, WHICH
MAY BE DEFECTIVE.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 18 (20)
6.2 EU Regulatory Compliance
Company Name:
Postal address:
Postcode:
City:
Telephone number:
E-mail address:
Product:
EU Declaration of Conformity (DoC)
We
Kvaser AB
Aminogatan 25
431 53
M¨olndal
+46 31 886344
sales@kvaser.com
declare that the DoC is issued under our sole responsibility and belongs to the following product:
Kvaser USBcan Light 4xHS
Object of the declaration (identification of apparatus allowing traceability):
Product: Kvaser USBcan Light 4xHS
Type: 73-30130-00831-1
The object of the declaration described above is in conformity with the relevant Union harmoni-
sation legislation:
Chemical substances (REACH) Regulation (EC) No 1907/2006
Electromagnetic Compatibility (EMC) Directive 2014/30/EU
RoHS recast Directive 2011/65/EU
Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU
The following harmonised standards and technical specifications have been applied:
Title, Date of standard/specification:
EN 55022 (2010) EN 55024 (2010)
EN 61000-6-3 (2007 + A1:2011) EN 50581 (2012)
EN 50419 (2005)
Signed for and on behalf of:
M¨olndal
Place of issue
2017-08-25
Date of issue Claes Haglund, Supply Chain and Quality director
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 19 (20)
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his/her own expense.
6.3 Patents, Copyrights and Trademarks
All trademarks are the property of their respective owner. Windows is a registered
trademark of Microsoft Corporation in the United States and other countries.
Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks
of Adobe Systems Incorporated in the United States and/or other countries.
MagiSync is a trademark of Kvaser AB.
DeviceNet is a trademark of Open DeviceNet Vendor Association, Inc.
NMEA 2000 is the registered trademark of the National Marine Electronics
Association, Inc.
For information about Kvaser related CAN patents, see www.kvaser.com/patent.
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Kvaser USBcan Light 4xHS User’s Guide 20 (20)
7 Document Revision History
Version history for document UG_98176_usbcan_light:
Revision Date Changes
1.0 2015-09-02 Initial version
1.1 2015-10-29 Minor textual changes
1.2 2016-02-04 Minor textual changes
1.3 2017-01-09 Updated compliance text, added link to patents
2.0 2017-08-25 Updated EU Declaration of Conformity
3.0 2018-01-29 Corrected power consumptions, “Kvaser Device
Guide” has replaced “Kvaser Hardware”
3.1 2018-05-07 Minor textual changes
Kvaser AB, Mölndal, Sweden — www.kvaser.com
Loading...