Congratulations, you now own Kustom's KPM7200 Powered Mixer,
a 24-bit digital, portable and powerful 200 Watt PA mixer/amplifier.
The Kustom KPM7200 is easy to operate and easy to understand. Before operating your
KPM7200, please read and understand all setup and safety instructions.
ENGLISH FRENCH
Danger
Exposure to extremely high noise levels may cause a permanent hearing loss.
Individuals vary considerably to noise induced hearing loss but nearly everyone will
lose some hearing if exposed to sufficiently intense noise for a sufficient time.
The U.S. Government's Occupational Safety and Health Administration (OSHA) has
specified the following permissible noise level exposures:
Danger
L’exposition a des niveaux eleves de bruit peut provoquer une perte permanente
de l’audition. Chaque organisme humain reagit differemment quant a la perte de
l’audition, mais quasiment tout le monde subit une diminution de l’acuite auditive
lors d’une exposition suffisamment longue au bruit intense. Les autorites
competentes en reglementation de bruit ont defini les expositions tolerees aux
niveaux de bruits:
DURATION PER DAY (HOURS) 8 6 4 3 2 1
SOUND LEVEL (dB) 90 93 95 97 100 103
According to OSHA, any exposure in the above permissible limits could result in
some hearing loss. Ear plugs or protectors in the ear canal or over the ears must
be worn when operating this amplification system in order to prevent a permanent
hearing loss. If exposure in excess of the limits as put forth above, to insure against
potentially harmful exposure to high sound pressure levels, it is recommended that
all persons exposed to equipment capable of inducing high sound pressure levels,
such as this amplification system, be protected by hearing protectors while this unit
is in operation.
CAUTIO
RISK OF ELECTRIC
SHOCK
CAUTION:
TO REDUCE THE RISK O F ELECTRIC SHOCK,
DO NOT REMOVE CHASSIS. NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF NONINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT
MAY BE OF SUFFICIENT MAGNITUDE T O CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
DURE EN HEURES PAR JOUR 8 6 4 3 2 1
NIVEAU SONORE CONTINU EN dB 90 93 95 97 100 103
Selon les autorites, toute exposition dans les limites citees ci-dessus, peuvent
provoquer certaines pertes d’audition. Des bouchons ou protections dans
l’appareil auditif ou sur l’oreille doivent etre portes lors de l’utilisation de ce
systeme d’amplification afin de prevenir le risque de perte permanente de
l’audition. Dans le cas d’expositions superieures aux limites precitees il est
recommande, afin de se premunir contre les expositions aux pressions
acoustiques elevees potentiellement dangeureuses, aux personnes exposees
aux equipements capables de delivrer de telles puissances, tels ce systeme
d’amplification en fonctionnement, de proteger l’appareil auditif.
ATTE NTI
RISQUE DE CHOC
ELECTRIQUE
ATTENTI
CE SYMBOLE A POUR BUT D’AVERTIR L’UTILISATEUR DE LA
PRESENCE DE VOLTAGE DANGEREUX NON-ISOLE A L’INTERIEUR
DE CE PRODUIT QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT
IMPORTANTE POUR PROVOQUER UN CHOC ELECTRIQUE AUX
PERSONNES.
AFIN DE LIMITER LE RISQUE DE CHOC ELECTRIQUE,
NE PAS ENLEVER LE CHASSIS. NE CONTIENT PAS
DE PIECES POUVANT ETRE REPAREE PAR
L’UTILISATEUR. CONFIER LE SERVICE APRESVENTE AUX REPARATEURS AGREES.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
IMPORTANT
1. Read all safety and operating instructions before using this product.
2. All safety and operating instructions should be kept for future reference.
3. This product should not be used near water i.e. bathtub, sink, swimming
pool, wet basement, etc.
4. This product should be located so that its position does not interfere with
proper ventilation. It should not be placed flat against a wall or placed
in a built-in enclosure that will impede the flow of cooling air.
5. This product should not be placed near a source of heat, such as a
stove, radiator, or another heat producing amplifier.
6. Connect only to a power supply of the type indicated on the back of the
amplifier near the power supply cord.
7. Do not break off the ground pin of the power supply cord.
8. Power supply cords should always handled carefully. Never walk or place
equipment on power supply cords.
9. The power supply cord should be unplugged when the unit is unused
for long periods of time.
10. Care should be taken so that objects do not fall and liquids are not spilled
into the unit through the ventilation ports or any other openings.
CE SYMBOLE A POUR BUT D’AVERTIR L’UTILISATEUR DE LA
PRESENCE D’INSTRUCTIONS D’UTILISATION ET DE MAINTENANCE
DANS LES DOCUMENTS FOURNIS AVEC CE PRODUIT.
IMPORTANT
1. Lisez toutes les instructions d’utilisation et de sécurité avant d’utiliser
ce produit.
2. Toutes les instructions d’utilisation et de sécurité doivent être conservées
afin de pouvoir s’y référer à tout moment.
3. Cet appareil ne doit pas être utilisé à proximité d’eau ou baignoire, évier,
piscine, sous-sol humide, etc.
4. Cet appareil doit être placé de telle sorte que sa position ne l’empêche
pas d’être ventilé. Il ne doit pas être placé à plat contre un mur ou dans
un espace encastré qui empêcherait la ventilation.
5. Cet appareil ne doit pas être place près d’une source de chaleur tel un
forneau, radiateur ou tout autre appareil produisant de la chaleur.
6. Branchez uniquement une alimentation électrique du type indiqué sur
l’arrière de l’amplificateur, près du cordon d’alimentation électrique.
7. Ne coupez pas la borne de terre du cordon d’alimentation électrique.
8. Les cordons d’alimention électrique doivent toujours être manipulés avec
précaution. Ne jamais marcher ni poser un équipement sur des cordons
d’alimentation électrique.
9. Le cordon d’alimentation électrique doit être débranché en cas de période
de non-utilisation prolongée.
10. Il faut prendre les précautions nécessaires afin de ne pas faire tomber d’objet
ni renverser du liquide dans l’appareil par les trous d’aération ou toute
autre ouvertune.
1
SETUP DIAGRAM A
MIXER FRONT
15 16 17 18 19
1
2
3
4
5
6
7 8 10 12 14139 11
20
21
22
23
24
25
26
SETUP DIAGRAM B
MIXER REAR
28
27
29
30
2
EXPLANATION OF CONTROLS
FRONT PANEL
1) Effects Controls: Adjusts the amount of signal that is sent to the digital effects processor.
2) Monitor Controls: Adjusts the amount of signal that is sent to the Master Monitor control.
3) Tone Controls: Adjusts the balance of bass and treble from the individual channels.
4) Main Controls: Adjusts the volume of the individual channel.
5) Line Input: Input connection for 1/4" line level sources (Keyboards, drum machines, etc.)
6) Microphone Input: Input connection for balanced Low-Z signals (Microphones, etc.)
7-8) Instrument Inputs: Input connection for instruments (Acoustic Guitars, Electric Guitars, etc.)
9) Effects Send: Output connector used to send a line level signal from the KPM7200 to an
outboard effect. This connector takes a signal feed from the individual channel's Effects controls.
10) Aux Return: Input connector used to receive a signal from an outboard effect or signal source. The signal from
this connector is fed to the effect Master (16) control. The Effect Master control (16) will adjust the volume of this signal
source.
11) Preamp Output: Line level output for the preamp. This control takes a signal feed from the Main Master control.
12) Power Amp Input: Input connector for the Power Amp. NOTE: When a line level signal source is inserted into
this connector, the signal from the Kustom KPM7200's individual channels are disconnected and will not function. Only
the outboard signal source will be amplified.
13) Monitor Output: Output connector to send a line level signal to a monitor amplifier or powered monitor.
14) Footswitch: Standard Tip-Ring-Sleeve wired footswitch to turn digital effects on and mute the channels of the
KPM7200. Tip connection turns the Effects on and off. The Ring connection will mute the individual channels.
15) Digital Effects Indicators: These LED's show what digital effects have been chose. NOTE: No LED's are lit
when the Effects are muted via footswitch.
16) Effects Master: Controls the volume of digital effect signal to the Main Master control.
17-18) Effect Select: These two push buttons will scroll through the digital effect options. Pressing the UP button will
advance the digital effect selection to the next selection higher than the present selection. Pressing the DOWN
button will advance the digital effect selection to the next selection lower than the present selection. NOTE: When
scrolling past the top or bottom of the effects selection, the effects selection will automatically go to the opposite end
of the selections.
19) Equalizer: These controls adjust overall tone of the mixer. Each slide control adjusts the amount of specific
frequencies + or
– 12dB.
20) Main Master: Controls the total volume on the individual channels. NOTE: The playback volume is not affected
by the Main Master control.
21) Power On Indicator: Power is on when LED is lit.
22) Monitor Master: Controls the total volume of the individual channel's monitor sends.
NOTE: The Monitor output is still active when Main channels are muted via footswitch.
3
23) Channels On Indicator: Channels are active when LED is lit.
24) Playback Volume: Controls the volume from the Playback RCA input jacks (25).
NOTE: The Playback feature is not affected by the Main Master control and will remain
active even when the mute function is active via the footswitch.
25) Playback RCA Jacks: Input connector CD, Tape or any line level stereo signal source.
Allows you to play recorded music through the mixer.
26) Record RCA Jacks: Output connectors to send line level signal to a record device such as a tape recorder or
computer.
REAR PANEL
27) AC Cord Connector: Insert the AC cord (supplied) firmly into the AC connector.NOTE: Replace the AC power
cord if protective jacket is damaged or round ground pin is damaged or removed.
28) Power Switch: The KPM7200 is turned ON when the switch is in the UP position.
Press the switch to the DOWN position when not in use.
29-30) Speaker: Connectors for 8 Ohm speaker cabinets each.
NOTES: #1 do not connect more than two 8 Ohm speaker cabinets to the output of the KPM7200 mixer/amplifier.
Total load must not go below 4 Ohms.
#2. It is not necessary to use both A & B output jacks.
The KPM7200 will operate at 8-16 Ohms.
QUICK-START SETUP INSTRUCTIONS
Making Connections:
• Connect 1/4" non-shielded speaker cables to the speaker out jacks on the rear of the KPM7200 (29 & 30),
then connect the opposite end of each speaker cable to the speaker enclosures.
• Connect instruments and microphones into the appropriate input connectors located on the front of the mixer.
Low Impedance Microphones (6), Line Level (5), High Impedance Instruments (7 &8), tape/CD (25).
• Make sure the power switch is turned to the off position and attach the AC power cable into the fused AC
input (27) located on the rear of the mixer.
Master Section:
• Turn the Main Master control (20), and Playback Master (24) counter clockwise.
• Adjust the master equalizer slide controls (19) to the center 0dB position.
Input Section:
• Turn all channel volume controls (4) counter clockwise.
• Turn all tone controls (3) to the 12 O'clock position.
4
PLAYING
• Press the Power switch (28) to the ON position.
• Turn the Main Master control (20) to the 12 O'clock position.
• Turn the Main control (4) clockwise on each channel to achieve the desired volume. (One channel at a time)
• After you are satisfied with the basic mix of the individual channels, use the Main Master control (20) to adjust
the overall volume of the mixer.
• Use the Graphic Equalizer slide controls (19) to control feedback and contour the audio to the overall desired
sound.
• Select a digital effect (if desired). The KPM7200 offers a choice of eight 24-bit
digital effects.
STAGE EFFECTS STUDIO EFFECTS
Large Room Chorus
Small Room Chorus / Reverb
Small Hall Slap-back Echo
Large Hall Delay
• Adjust the effects controls on the individual channels (1) to desired volume.
Adjust the effects Master control to achieve the total desired amount of effects
in the mix.
• Reset the Main master control (20) to desired volume.
That's it. Enjoy...
Servicing: The AC Fuse is accessible underneath the AC cable connector. No user serviceable parts inside. Please contact
your nearest Authorized Kustom Service Center or Kustom Inc. directly for service.
Kustom Inc. Customer Service can be reached at (513) 451-5000 ext. 504, service@kustom.com or locate an Authorized
Service Center from the World Wide Web at www.kustom.com.
5
6
KPM7200
Specifications
Model KPM7200 KPM7200 Powered Mixer
Output Power 200W 4 ohms @ 5% THD
160W 4 ohms @ 0.4% THD
Frequency Response 20Hz-20kHz Actual response is tailored to speaker cabinet for
accurate acoustical response.
Total Harmonic Distortion less than 0.4% Measured at 1VRMS (0dBv) at record output,
effects send, or insert output
Hum & Noise -115dB Mic Input, Rs=150 ohm, 20-20kHz
-60dB Residual N oise, all level controls 0% (minimum)
-50dB Nominal System Noise, all level controls at 50%
System Gain All measurements made at 1kHz
77dB Mic to Power Amp Out (Ch 1 - Ch 5)
60dB Line to Power Amp Out (Ch 1 - Ch 7)
70dB Instrument to Power Amp (Ch 6 - Ch 7)
36dB Playback to Power Amp
50dB Mic to Record Output
44dB Mic to Effects Send
50dB Mic to Preamp Output
50dB Mic to Monitor Output
Crosstalk 80dB Channel to channel, 1kHz
Input Channel Equalization Special curve that adjusts bass, mid, and treble frequencies
Master Equalization 100 to 10Khz, 7 Band, 1 Octave Graphic, all ±12dB
Digital Effects 24 bit DSP, 8 effects; small room, large room, small hall, large hall,
chorus, chorus reverb, slap back (delay), echo
Phantom Power +15V Applied to all Mic Inputs thru 3.3K resistors
Footswitch Digital effects ON/OFF and Channel ON/OFF (playback remains active)
Power Requirements USA/Canada 120VAC/60Hz, 160W nominal
Europe 230VAC/50Hz, 160W nominal
UK 230VAC/50Hz, 160W nominal
Australia 240VAC/50Hz, 160W nominal
Japan 100VAC/50-60Hz, 160W nominal
Dimensions mm/kg 210 (Height) x 480 (Width) x 270 (Depth), 11 kg
inches/pounds 8 1/4 (Height) x 19 (Width) x 10 5/8 (Depth), 24 lbs
7
EC Declaration of Conformity
We: Kustom Musical Amplification Inc.
4940 Delhi Pike
Cincinnati, OH 45238
Tel: 1-513-451-5000 Fax: 1-513-347-2298
www.kustom.com
Declare that the product
Product name: Kustom
Product model number: KPM7200, Contains one KPM7200
to which this declaration relates is in conformity with the following standards;
EN55013 (A12) : 1995 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and
associated equipment.
EN55020: 1995 Electromagnetic immunity of broadcast receivers and associated equipment.
EN61000-3-2: 1995 Limits for harmonic current emissions (equipment input current < 16A per phase).
EN61000-3-3: 1995 Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated
currents < 16A.
EN55103-1: 1995 Electromagnetic Compatibility - Product family standard for Audio, Video Audio-visual and
entertainment Lighting Control Apparatus.
EN60065: 1994 Safety requirements for main operated electronic and related apparatus for household and similar
general use.
Following the provisions of EU Council Directive(s): 72/73 EEC and 89/336/EEC.
We the undersigned, hereby declare that the equipment specified above conforms to the aforementioned directive(s).
Name of authorized person: Rick Kukulies, VP Engineering
Signature:______________________ Date: 05 June 2001
8
Kustom Inc., 4940 Delhi Pike, Cincinnati, OH • USA
(800) 999-5558 Fax: (513) 347-2192 / www.kustom.com
Loading...