OWNER'S MANUAL
KBA35X DFX
Congratulations on the purchase of your new Kustom amp! Your KBA35X DFX model
successfully draws on more than 30 years of amplifier design and manufacturing
experience at Kustom. This amp was planned from the ground up by our engineers to
offer top-notch tone and dependable performance. Inside this manual, you'll find useful
information about the amp's features and some suggested settings to illustrate its tonal
capabilities. We wish you many years of enjoyment with your Kustom amplifier.
Model
KBA35X
DFX
Power
30 W
Equalizer
4 Band
Channels
Impedance
One 8 Ohms
Effects
8 Preset
Digital EFX
Amplifier Type
MOS-FET Transistor
Dimensions Weight
11
//
15 ”x18 ”x12 ”
88
38.5x46x30.5 CM
34 Lbs.
15.5 Kg
EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A
PERMANENT HEARING LOSS. INDIVIDUALS VARY CONSIDERABLY TO
NOISE INDUCED HEARING LOSS BUT NEARLY EVERYONE WILL LOSE
SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A
SUFFICIENT TIME.
THE U.S. GOVERNMENT'S OCCUPATIONAL SAFETY AND HEALTH
ADMINISTRATION (OSHA) HAS SPECIFIED THE FOLLOWING PERMISSIBLE
NOISE LEVEL EXPOSURES:
DURATION PER DAY IN HOURS
8
6
4
3
2
1
1/2 HR. or LESS
ACCORDING TO OSHA, ANY EXPOSURE IN THE ABOVE PERMISSIBLE
LIMITS COULD RESULT IN SOME HEARING LOSS. EAR PLUGS OR
PROTECTORS IN THE EAR CANAL OR OVER THE EARS MUST BE WORN
WHEN OPERATING THIS AMPLIFICATION SYSTEM IN ORDER TO PREVENT A
PERMANENT HEARING LOSS. IF EXPOSURE IN EXCESS OF THE LIMITS AS
PUT FORTH ABOVE, TO INSURE AGAINST POTENTIALLY HARMFUL
EXPOSURE TO HIGH SOUND PRESSURE LEVELS. IT IS RECOMMENDED
THAT ALL PERSONS EXPOSED TO EQUIPMENT CAPABLE OF INDUCING
HIGH SOUND PRESSURE LEVELS, SUCH AS THIS AMPLIFICATION SYSTEM,
BE PROTECTED BY HEARING PROTECTORS WHILE THIS UNIT IS IN
OPERATION.
DANGER
SOUND LEVEL dB FLOW RESPONSE
90
93
95
97
100
103
110
WARNING!
! THIS APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING. NO OBJECTS FILLED WITH LIQUIDS SUCH AS
VASES SHALL BE PLACED ON THE APPARATUS.
! TO AVOID ELECTRICAL SHOCK, DO NOT DISASSEMBLE.
REFER SERVICING TO QUALIFIED PERSONAL ONLY!
IMPORTANT
1. Read all safety and operating instructions before using this product.
2. All safety and operating instructions should be kept for future reference.
3. Obey all cautions in the operating instructions and on the back of the unit.
4. All operating instructions should be followed.
5. This product should not be used near water i.e. bathtub, sink, swimming pool,
wet basement, etc.
6. This product should be located so that its position does not interfere with
proper ventilation. It should not be placed flat against a wall or placed in a
built-in enclosure that will impede the flow of cooling air.
7. This product should not be placed near a source of heat, such as a stove,
radiator, or another heat producing amplifier.
8. Connect only to a power supply of the type indicated on the back of the
amplifier near the power supply cord.
9. Do not break off the ground pin of the power supply cord.
10. Power supply cords should always handled carefully. Never walk or place
equipment on power supply cords. Periodically check cords for cuts or signs of
stress, especially at the point where the cord exits the unit.
11. The power supply cord should be unplugged when the unit is unused
for long periods of time.
12. If this product is to be mounted in an equipment rack, rear support should be
provided.
13. Metal parts and vinyl covering may be cleaned with a damp rag.
14. Care should be taken so that objects do not fall and liquids are not spilled into
the unit through the ventilation ports or any other openings.
15. This unit should be checked by a qualified service technician if:
A. The power supply cord or plug has been damaged.
B. Anything has fallen or been spilled into the unit.
C. The unit does not operate correctly.
D. The unit has been dropped or the enclosure damaged.
16. The user should not attempt to service this equipment. All service work
must be done by a qualified service technician for warranty repairs.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
NOT REMOVE CHASSIS. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE
PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THE UNIT.
Kustom Inc., 4940 Delhi Pike, Cincinnati, OH • USA
(800) 999-5558 Fax: (513) 347-2192 / www.kustom.com
THIS AMPLIFIER HAS BEEN DESIGNED AND CONSTRUCTED
CAUTION
TO PROVIDE ADEQUATE POWER RESERVE FOR PLAYING
MODERN MUSIC WHICH MAY REQUIRE OCCASIONAL PEAK
POWER. EXTENDED OPERATION AT ABSOLUTE MAXIMUM
POWER IS NOT RECOMMENDED SINCE THIS COULD
DAMAGE THE ASSOCIATED LOUDSPEAKER SYSTEM.
PLEASE BE AWARE THAT MAXIMUM POWER CAN BE
OBTAINED WITH VERY LOW SETTINGS OF THE MASTER
VOLUME CONTROLS IF THE INPUT SIGNAL IS VERY STRONG.
CD/TAPE
INPUT
GUITAR
INPUT
VOLUME
EQUALIZER
LOW HI-MID
LO-MID HIGHNOTCHLEVEL
DIGITAL EFFECTS
LEVEL PROGRAM
EFFECTS
ON
ON
OFF
OFF
1. LITE CHORUS 1
2. LITE CHORUS 2
5
1
3. MEDIUM CHORUS
6
4. HEAVY CHORUS
5. FLANGE 1
7
6. FLANGE 2
7. SLAPBACK
8
8. DELAY
4
3
2
KBA35X DFX
POWER
1 2
3
4
5
6
7
8
9
10
11
12
13
1.) CD/Tape Input - this 1/4" 3 conductor jack will allow you to plug in a CD player, tape or any other source
to practice along with. It sums the left and right signals into a mono signal and passes it through to the
amplifier section. To control the volume of the source, adjust the output volume of the device. We suggest
you turn the volume all the way down then plug in and adjust the volume according to your taste.
2.) Guitar Input - this is a 1/4" 2 conductor input jack for plugging in your instrument. It is intended for bass
guitar or Hi-Z microphones but will accept other instruments as well.
3.) Volume Level - this control is the output volume control for the bass guitar input. Slowly increase the
control to increase the volume. If you are using a bass guitar with an on-board preamp, set it's level for a
mid position before increasing this control otherwise distortion may occur.
4.) Notch - this control is a dramatic cut filter. It is "notched" at a rate of -15db. The width of the notch is set at
one octave and can be swept from 45 Hz to 1KHz. It will create a very precise subtraction of undesirable
overtones or allow you to fine tune your tone settings.
5.) Low - this control is the bass control. It is active and set to boost or cut frequencies at 60 Hz. This will
effect the low frequency signals. Turning it fully clockwise, the signal is boosted 15 db. Turning it
counterclockwise, the low will be rolled off -15db. Especially good for making low output, thin toned bass
guitars sound fuller.
6.) Lo Mid - this control is the Low Midrange control. It is active and set to boost or cut frequencies at 250Hz
This will effect the mid-low frequency signals. Turning it fully clockwise, the signal is boosted 10 db.
Turning it counterclockwise, the low-mids will be rolled off -10db. Especially good for "cleaning up" muddy
bass guitar overtones.
7.) Hi Mid - this control is the High Midrange control. It is active and set to boost or cut frequencies at
1.5KHz. This will effect the mid-high frequency signals. Turning it fully clockwise, the signal is boosted 10
db. Turning it counterclockwise, the low-mids will be rolled off -10db. Increasing this will add punch to a
bass guitars' sound.
8.) High - this is the high frequency control. It is active and set to boost or cut frequencies at 8KHz. This will
effect the high frequency signals. Turning it fully clockwise, the signal is boosted 15 db. Turning it
counterclockwise, the highs will be rolled off -15db. This will add or subtract the high end attack of
slapping style sounds or pick attack and clarity.
9.) Effects On/Off - this switch engages the digital effects section.
10.) Effects Level - this control adds the digital effects section and mixes it into the main signal buss. Several
different effects are available.
11.) Program Select - this switch will select any of eight different effects. 4- Chorus, 2- Flanges, 2- Chorus,
and 2- delay.
12.) Jewel Light - this jewel light lets you know that the amplifier is on.
13.) Power - this switch turns on and off the AC power to the amp.
Back Panel - (not pictured)
Speaker Out - this is a 2 conductor 1/4" speaker output jack. This will disconnect the internal speaker and
allow an external speaker cabinet to be employed. Rating is 8 ohms.
Line Output - this is a 2 conductor 1/4" line output jack. This will allow an external amplifier or mixing
board to be supplied with the signal from this amp. This is output is attenuated and comes from the power
amp signal.
Headphone Jack - this is a 1/4" 3 conductor jack for plugging headphones. It will sum the signal and put
the sound in both ears, thereby creating a pseudo-stereo sound. Volume will be determined by the volume
control on the channel you are on. It will disconnect the internal speaker when plugged into. This will allow
quiet practicing.
Footswitch- this is a mono 1/4” jack. Plug a single non LED type footswitch (optional) into this jack to
turn the digital effects on and off.
Suggested Settings
(These settings are general starting points. They
are designed to get you close to the sound you
are looking for. If the control is not shown, then it
doesn't apply to this particular sound. )
VOLUME
EQUALIZER
LOW HI-MID
LO-MID HIGHNOTCHLEVEL
DIGITAL EFFECTS
LEVEL PROGRAM
EFFECTS
ON
ON
OFF
OFF
1. LITE CHORUS 1
2. LITE CHORUS 2
5
1
3. MEDIUM CHORUS
6
4. HEAVY CHORUS
5. FLANGE 1
7
6. FLANGE 2
7. SLAPBACK
8
8. DELAY
4
3
2
Traditional Electric Bass Setting - in this setting the amplifier will deliver a standard electric bass
sound. Whether you are playing rock, country, blues or gospel, this setting will get you close.
Because of the Active EQ, you will be able to dial in your preferences from here. If you play with a
pick and want less top end attack on the notes, roll off a bit of the High control. If it's deeper bottom
your looking for, add more low and low mid. The key is to experiment to achieve your own personal
sound.
VOLUME
EQUALIZER
LOW HI-MID
LO-MID HIGHNOTCHLEVEL
DIGITAL EFFECTS
LEVEL PROGRAM
EFFECTS
ON
ON
OFF
OFF
1. LITE CHORUS 1
2. LITE CHORUS 2
5
1
3. MEDIUM CHORUS
6
4. HEAVY CHORUS
5. FLANGE 1
7
6. FLANGE 2
7. SLAPBACK
8
8. DELAY
4
3
2
Funk "Slap" Sounds - this style of music needs a good strong attack sound with lots of top end.
Usually a hollowed out middle will produce the extra top end necessary for the punch needed for this
style of music. If you are using a more thumb style, a bit more low end and volume might be needed
for your particular style of playing. Or less if you really hit it hard. Even though this is a practice or
rehearsal level amplifier, it will deliver the punch and clarity that you require. Remember to try this
amp with an additional speaker plugged in. You'll be nicely surprised.
VOLUME
EQUALIZER
LOW HI-MID
LO-MID HIGHNOTCHLEVEL
DIGITAL EFFECTS
LEVEL PROGRAM
EFFECTS
ON
ON
OFF
OFF
1. LITE CHORUS 1
2. LITE CHORUS 2
5
1
3. MEDIUM CHORUS
6
4. HEAVY CHORUS
5. FLANGE 1
7
6. FLANGE 2
7. SLAPBACK
8
8. DELAY
4
3
2
Alternative Style - this setting is designed for a upper end punch and edge that will cut through most
any sound. This style will work well with pick or fingers and will add a touch of distortion to the sound
as well. Make sure your instrument's volume control is up all the way. Since you are adding volume,
you need to be careful with the actual amount of e.q.. you use as it also can add distortion to the
sound. Also, you may want to use a compressor pedal in the signal chain before the amp to give it a
smoother sound but still "edgy". As in all the settings above, it is strictly a matter of personal taste in a
achieving the sound you are looking for.....experiment.
Loading...